Name: torsion formula for circular shafts
Uploaded: 2024-05-23T12:59:40.000Z
Duration: 1 min 13 s
Channel: JoVE

円形シャフトに加えられるトルクがフックの法則制限内にあるため、永久的な変形がない場合を考えてみましょう。
ここで、せん断ひずみの表現を思い出してください。これに剛性係数を掛け、せん断応力とひずみにフックの法則を使用すると、シャフトのせん断応力の式を決定できます。
シャフトの任意の断面に加えられる基本力のモーメントの合計は、シャフトに加えられるトルクの大きさに等しくなければならないことを思い出してください。
せん断応力を代入し、項を並べ替えると、積分項を持つ式が得られ、これはその中心に対する断面の極性慣性モーメントを表します。
さらに再配置し、最大せん断応力を置換すると、剛性のある均一な円形シャフトのせん断応力の弾性ねじり式が得られます。
ただし、内側半径と外側半径がr1とr2である中空シャフトの場合、極慣性モーメントは2つの半径の4乗の差として表されます。

円形シャフト - 線形範囲の応力

Circular Shaft - Stresses in Linear Range

円形シャフトがフックの法則の範囲内に留まるトルクを受け、永久変形を回避するシナリオを考えてみましょう。 そこで、せん断ひずみの公式を再考します。 この式に剛性係数を乗じて、せん断応力とひずみのフックの法則が適用されます。 その結果、シャフト内のせん断応力の方程式を導くことができます。

<img alt="Equation 1" src="/files/ftp_upload/15614/15614_Equation_1.svg" style="height: 28px;">

さらに、シャフトの任意の断面に作用する基本力のモーメントの合計は、そのシャフトに加えられるトルクと同一でなければならないことを覚えておくことが重要です。 せん断応力を置き換えるように方程式を調整すると、積分項が現れます。 この項は、断面の中心に関する極慣性モーメントを意味します。 最大せん断応力をさらに調整および代入した後、均一に剛性のある円形シャフトのせん断応力について弾性ねじり公式を導き出すことができます。

<img alt="Equation 2" src="/files/ftp_upload/15614/15614_Equation_2.svg" style="height:40px;">

ただし、r_1 と r_2 が内半径と外半径として表される中空シャフトではシナリオが異なります。 この場合、極慣性モーメントは両方の半径の 4 乗の差として表されます。

円形シャフトに加えられるトルクがフックの法則制限内にあるため、永久的な変形がない場合を考えてみましょう。
さて、思い出してください...

Education

JoVE Core

Mechanical Engineering

機械工学

Unit 1

ユニット1

Torsion

ねじれ

KEY TERMS AND CONCEPTS

主要用語と概念

torsion formula for circular shafts

Torsion in a circular shaft is analyzed when the applied torque stays within Hooke's law. In this linear range, the shaft does not undergo permanent deformation. The discussion uses shearing strain, shearing stress, and the modulus of rigidity to build the stress equation.

The derivation also requires the moments of the small forces on a cross-section to equal the applied torque. When the shearing stress expression is rewritten, an integral term appears. This term represents the polar moment of inertia, which measures how the cross-section resists twisting about its center.

After the maximum shearing stress is substituted, the elastic torsion formula is obtained for a uniformly rigid circular shaft. The same idea is then applied to a hollow shaft. For that case, the polar moment of inertia depends on the inner radius r1 and outer radius r2, and it is given by the difference of their fourth powers.

Torsion Formula for Circular Shafts

stresses in a shaft

Torque and Shear in a Twisted Shaft

A shaft under torque develops internal shear forces as it twists. In this setup, equal and opposite torques act on the shaft PQ. To study the effect, a section is cut perpendicular to the shaft axis at an arbitrary point R. The free-body diagram of the QR segment shows the shearing forces applied by the PR portion. These forces act as the shaft resists twisting. Using equilibrium on the QR segment links the internal shear forces in the cut section to the internal torque. Here, r is the...

deformation in a circular shaft

Shear Strain in a Circular Shaft

Shear strain in a circular shaft describes how the shaft’s surface changes shape under torsion. A circular shaft keeps each cross-section flat and undistorted as it twists. Each section behaves like a rigid slab that rotates in place. To study the strain inside the shaft, consider a cylindrical section with length L and radius R. One end of this section is fixed. The radius at a point inside the section is labeled r. Before the load is applied, a small square element lies on the surface of...

circular shaft - stresses in linear range

Torsion in a circular shaft is analyzed when the applied torque stays within Hooke's law. In this linear range, the shaft does not undergo permanent deformation. The discussion uses shearing strain, shearing stress, and the modulus of rigidity to build the stress equation. The derivation also requires the moments of the small forces on a cross-section to equal the applied torque. When the shearing stress expression is rewritten, an integral term appears. This term represents the polar moment...

angle of twist - elastic range

Elastic Twist in a Circular Shaft

Elastic twist in a circular shaft describes how a cylindrical shaft rotates when torque is applied. The shaft has a length L and a uniform radius r. A torque at the free end creates shearing strain, which is greatest at points farther from the shaft axis. When the shaft stays within the elastic range, the shearing strain can be written in terms of the applied torque, radial distance, polar moment of inertia, and modulus of rigidity. The polar moment of inertia is a geometric measure of how the...

angle of twist: problem solving

Shaft Torsion Between Pulleys B and C

Shaft torsion between pulleys B and C is found by analyzing how torque twists an aluminum shaft. An electric motor applies 700 N·m of torque and produces stable rotation. The shaft carries pulleys B and C, which experience torques of 300 N·m and 400 N·m. The calculation starts with a section cut between pulleys B and C. A free-body diagram is used to study the cut cross-section. Because pulley B has an anticlockwise torque, the torque at the cut must balance it in the opposite direction. The...

design of transmission shafts

Sizing a Transmission Shaft by Torque

A transmission shaft is sized from the power it must carry and the speed it rotates at. These two design limits guide the choice of shaft material and cross-sectional size. The goal is to keep the maximum shearing stress within the elastic limit while still transmitting the needed power. Power is directly linked to torque, which is the twisting force applied to the shaft. By rearranging the power relation, the torque can be found from the required power and the shaft speed. That torque value...

stress concentrations in circular shafts

Why Shafts Develop Local Stress Peaks

Circular shafts can develop local stress peaks when torque is applied through real machine parts. The elastic torsion formula works best for a circular shaft with a uniform cross-section and rigid plates fixed to its ends. In practice, torque is often passed through flange couplings or gears, and these parts use keys in keyways to connect to the shaft. That loading method changes the stress pattern near the point where torque enters the shaft. The stress distribution no longer matches the...

plastic deformation in circular shafts

Torsional Failure and Plastic Strain in Shafts

Plastic deformation in circular shafts happens when torsional force pushes the material past its yield strength. At that point, the shaft does not return to its original shape. Instead, it keeps a permanent strain. To measure this change, the stress pattern inside the shaft must be understood. The maximum shearing stress is calculated first. Then a shearing-stress-strain diagram can be drawn to find the maximum shearing strain. Shearing strain changes linearly with the distance from the shaft...

circular shafts - elastoplastic materials

Torsion Limits in Circular Shafts

Circular shafts under torsion show a clear change from elastic behavior to plastic deformation as torque increases. In the elastic limit, stress rises in direct proportion to the distance from the shaft’s center. The outer material carries the highest stress first, and the shaft can still return to its original shape. At a critical stress level, the shaft begins to yield. This marks the maximum torque the shaft can carry without permanent deformation. Beyond this point, a plastic region forms...

residual stresses in circular shafts

Residual Stress After Shaft Torsion

Residual stress can remain in a circular shaft after torque causes plastic deformation. This happens in elastoplastic materials, which show both elastic and plastic behavior. The plastic change can come from high shearing stress or large strain. Residual stress is the internal stress that stays in the material after the external force is removed. In a shaft under torque, the angle of twist does not return fully to its original value. That lasting change shows that residual stress is still...

torsion of noncircular members

Torsion in Square and Rectangular Bars

Torsion in square and rectangular bars shows how shape changes the way a material twists. Circular shafts keep their cross-sections nearly unchanged because they are axis-symmetric. That symmetry helps the stress spread evenly, so the shaft can resist torsion without distorting. Square bars behave differently because they do not have the same axial symmetry. When twisted, their cross-sections distort, although the diagonals and the lines connecting the midpoints stay as exceptions. This means...

thin-walled hollow shafts

Shear Flow in Thin-Walled Shafts

Shear flow in a thin-walled hollow shaft describes how torsional force is carried through the wall. When a small segment of width dx is isolated, it is still in equilibrium, but it experiences torsional shearing forces at its ends. These forces come from the longitudinal shearing stress on the segment's minor surface multiplied by that surface area. The result is a uniform shear flow through the structure. To study the wall more closely, a small section with length ds is considered. The force...

key terms and concepts

Learn how torque, shearing stress, and polar moment of inertia lead to the elastic torsion formula for solid and hollow circular shafts in the linear range.

Torsion Formula for Circular Shafts | JoVE K12

JoVE Core 機械工学は、平衡、力、トラス解析、構造力学などの重要なトピックをカバーする簡潔でわかりやすいアニメーション ビデオを提供します。実際のアプリケーションを探索し、科学者主導の実験を通じてこれらのコンセプトが実際に動作しているのを目撃してください。

mechanical engineering

Torsion Formula for Circular Shafts

Description

Transcript