Name: bjt frequency limits and gain drop
Uploaded: 2024-07-08T13:20:34.000Z
Duration: 1 min 17 s
Channel: JoVE

コモンベース構成の電流ゲインは、入力信号の低周波数では一定ですが、カットオフ周波数と呼ばれる特定の周波数を過ぎると減衰します。
アルファのカットオフ周波数は、電流ゲインが低周波電流ゲインの0.707倍になる周波数です。
同様に、ベータカットオフ周波数は、共通のエミッタ構成に対して定義されます。このカットオフ周波数は、アルファ カットオフ周波数よりもはるかに小さくなります。
共通のエミッタ・ゲインの大きさがユニティになる周波数は、トランジション・カットオフ周波数と呼ばれます。トランジションのカットオフ周波数は、アルファのカットオフ周波数よりもわずかに低くなっています。
遷移周波数は、キャリアがエミッタからコレクタに到達するのにかかる時間の合計時間で表すこともできます。これには、エミッタ遅延時間、基本通過時間、およびコレクタ通過時間が含まれます。
最も重要な遅延時間は、マイノリティの運送業者が基地を横断するために必要な期間である基本通過時間です。
この通過時間を短縮するために、高周波トランジスタは狭いベース幅で設計されています。

bjt のカットオフ周波数

バイポーラ接合トランジスタ (BJT) のカットオフ周波数は、信号の通過帯域と阻止帯域の間の遷移を示し、周波数の増幅または減衰におけるパフォーマンスに影響します。これらの周波数は、電子回路の特定の動作要件を満たすように BJT を設計する上で重要です。

αカットオフ周波数: 共通ベース構成に関連するαカットオフ周波数は、電流ゲインαが安定する上限周波数を定義します。周波数がこの臨界点を超えて増加すると、αが減少し、トランジスタの信号増幅効率が低下します。
βカットオフ周波数: 共通エミッタ構成でより関連性の高いβカットオフ周波数は、αカットオフ周波数よりも大幅に低くなります。これは、共通エミッタ電流ゲインβが低下し始め、アンプのパフォーマンスに悪影響を与える周波数を表します。
遷移周波数: この周波数はβカットオフ周波数よりわずかに低く、BJT のゲイン帯域幅積を表します。これはアンプのゲインが 1 になる周波数であり、トランジスタがアンプとして効果的に機能できる最高周波数を示します。
キャリア通過時間: 遷移周波数は、キャリアがエミッタからコレクタに移動する合計時間も反映し、エミッタ遅延時間、ベース通過時間、コレクタ通過時間を組み込んでいます。ベース通過時間は特に重要です。ベース幅を狭くしてベース通過時間を最小限に抑えると、BJT の高周波応答が向上します。
これらのカットオフ周波数は、特に高周波アプリケーションで BJT の周波数動作を理解して最適化し、有効範囲内で動作するようにするために不可欠です。

BJT のカットオフ周波数

コモンベース構成の電流ゲインは、入力信号の低周波数では一定ですが、特定の周波数と呼ばれる周波数を超えると減衰します。

Education

JoVE Core

Electrical Engineering

電気工学

Unit 1

ユニット1

Transistors

トランジスタ

KEY TERMS AND CONCEPTS

主要用語と概念

Cut-off Frequency of BJT

bjt frequency limits and gain drop

BJT frequency limits show when a bipolar junction transistor stops keeping a steady gain. These limits matter because they mark the shift from the pass band to the stop band in an electronic signal. They help explain why a transistor may amplify one range of frequencies well and weaken signals at higher frequencies.

The alpha cut-off frequency applies to the common-base configuration. At low frequencies, the current gain alpha stays stable. Beyond this upper-frequency limit, alpha drops and the transistor becomes less effective at amplifying the signal.

The beta cut-off frequency is more important in the common-emitter configuration. It is much lower than the alpha cut-off frequency. At this point, the common-emitter current gain beta begins to fall, and amplifier performance starts to decline.

The transition frequency comes slightly below the beta cut-off frequency. It shows the gain-bandwidth product of the BJT. At this frequency, the amplifier gain equals one, so it is the highest frequency at which the transistor can still work effectively as an amplifier.

Carrier transit times also help explain this high-frequency behavior. The transition frequency reflects the time carriers take to move from the emitter to the collector. That total time includes emitter delay time, base transit time, and collector transit time. Base transit time is especially important, and a narrower base can reduce it and improve high-frequency response.

BJT Frequency Limits and Gain Drop

bipolar junction transistor

BJT Structure and Carrier Flow

Bipolar junction transistors are important parts of electronic circuits. They help make amplifiers, memories, and microprocessors work. A BJT can be built as either NPN or PNP, depending on its doping pattern, which means the type of impurities added to the material. A BJT has three layers: the emitter, base, and collector. It also has two p-n junctions, so the device has a sandwich-like structure. The emitter is heavily doped so it can inject charge carriers into the base. The base is very...

configurations of bjt

BJT Amplifier Modes and Uses

Bipolar Junction Transistor (BJT) configurations are defined by which terminal is shared by the input and output circuits. The shared terminal can be the base, emitter, or collector. Each setup has different electrical behavior and fits different circuit needs. In the common base configuration, the base is the common terminal. This setup has high voltage gain, so it can work well in single-stage amplifier circuits such as microphone pre-amplifiers. It also reduces the input current signal...

working principle of bjt

PNP BJT Current Flow in Active Mode

PNP bipolar junction transistors control current flow by moving charge carriers between the emitter, base, and collector. In a common-base setup, the transistor can amplify or switch electronic signals when it operates in active mode. In a PNP transistor, the emitter is heavily doped with holes, which are positive charge carriers. The base is lightly doped with electrons, which are negative carriers. A forward bias across the emitter-base junction lowers the potential barrier and lets holes...

characteristics of bjt

BJT Current-Voltage Curves in Common Emitter

The Bipolar Junction Transistor (BJT) in a common-emitter setup is studied by measuring its current-voltage curves. These measurements show how the transistor responds when voltage and current are changed in a controlled way. They are key to understanding how a BJT works in electronic circuits. The input characteristics are found by varying the base-emitter voltage while keeping the collector-emitter voltage constant. This test shows a Shockley-type relationship between the collector current...

modes of operations of bjt

BJT Biasing: Active to Inverted Mode

A bipolar junction transistor (BJT) works in four modes that depend on how its two junctions are biased. Those modes are active, saturation, cut-off, and inverted. The biasing pattern controls whether the transistor amplifies current or acts like a switch. Active mode is the most common mode for amplification. In this mode, the emitter-base junction is forward-biased and the base-collector junction is reverse-biased. Electrons move from the emitter into the base, while the collector blocks...

frequency response of bjt

BJT Amplifier Response at Low and High Freq

A BJT amplifier’s response changes with frequency in a common-emitter circuit. Its behavior at low frequencies and high frequencies depends on the circuit’s equivalent model. These models help explain how the transistor handles AC signals. At low frequencies, the DC bias point sets the transistor’s operation. The emitter-base voltage, base current, and collector current define this bias point. The load line also shapes how the amplifier works, using the applied voltage and load resistance. <br...

cut-off frequency of bjt

BJT frequency limits show when a bipolar junction transistor stops keeping a steady gain. These limits matter because they mark the shift from the pass band to the stop band in an electronic signal. They help explain why a transistor may amplify one range of frequencies well and weaken signals at higher frequencies. The alpha cut-off frequency applies to the common-base configuration. At low frequencies, the current gain alpha stays stable. Beyond this upper-frequency limit, alpha drops and...

switching of bjt

BJT as a Digital On-Off Switch

Bipolar junction transistors (BJTs) can work as digital on-off switches in electronic circuits. In this mode, the transistor moves between cut-off and saturation. These two states match the off and on positions of an ideal switch. In cut-off mode, both the emitter-base junction and the collector-base junction are reverse-biased. This blocks current flow through the transistor and keeps it off. Circuits use this state when no signal transmission is needed, which helps maintain a low-power...

bjt amplifiers

Common-Emitter BJT Voltage Gain

Bipolar junction transistors, or BJTs, can act as amplifier parts when they work in the active region. In this mode, a small change in base-emitter voltage controls a larger collector current. That makes the transistor act like a voltage-controlled current source and lets it boost a weak signal into a stronger one. A common-emitter BJT amplifier uses that current change to create voltage gain. The output current flows through a load resistor, and the voltage drop across that resistor sets the...

small-signal analysis of bjt amplifiers

BJT Amplifier Gain and Input Resistance

BJT amplifier gain and input resistance can be analyzed with a small-signal model. In the active region, a bipolar junction transistor is used for linear amplification. Its base-emitter voltage includes a DC bias and a small AC signal. That input produces a collector current with both DC and AC parts. When the AC input signal is much smaller than the thermal voltage VT, the small-signal approximation applies. This makes it possible to find the AC collector current from the DC collector current...

field effect transistor

Field Effect Transistor Types and Uses

Field-effect transistors, or FETs, are important parts of electronic circuits. They have three terminals: gate, drain, and source. FETs are unipolar devices, which means they use either electrons or holes as charge carriers. That is different from bipolar transistors, which use both types of carriers. A FET controls the flow of charge from the source to the drain through a channel. The voltage difference between the gate and source controls how well that channel conducts. This makes the device...

characteristics of jfet

JFET Output Regions and Current Control

JFET output characteristics show how drain current changes with drain-source voltage and gate-source voltage. In a junction field effect transistor, the gate-source voltage controls the drain current. When the drain and gate voltages are set to zero, the device is in equilibrium and no net current flows. With the gate voltage held at zero, the drain current rises linearly as the source-drain voltage increases. This linear part is called the Ohmic region. In this region, the JFET acts like a...

biasing of fet

JFET Gate-Source Bias and Current Control

JFET gate-source bias controls current flow in a junction field effect transistor. A JFET uses one carrier type and comes in N-channel or P-channel forms. In both cases, the channel is surrounded by PN junctions, and those junctions help control how current moves through the device. In an N-channel JFET, N-type material forms the channel on a P-type substrate. The gate is made of P-type material. Biasing this device means applying a negative voltage to the gate relative to the source. That...

mos capacitor

MOS Capacitor Voltage and Charge

A MOS capacitor uses voltage to control charge in a semiconductor. It is a key structure in semiconductor device technology and in the fabrication of integrated circuits and MOSFETs, or metal-oxide-semiconductor field-effect transistors. The structure has three layers. A metal gate sits on top and is usually made from a highly conductive material such as aluminum or polysilicon. Below it is a thin insulating oxide layer, usually silicon dioxide (SiO2), and below that is a semiconductor...

mosfet

MOSFET Current Control in Electronics

The MOSFET is a semiconductor device that controls electrical current in modern electronics. It is also called an IGFET or MISFET. The three main terminals are the source, drain, and gate. MOSFETs are classified as n-channel or p-channel devices. The type depends on the doping of the substrate and the source or drain regions. In an n-MOSFET, the source and drain are n-type regions separated from a p-type substrate by reverse-biased p-n diodes. The gate is built from a metal plate over an...

characteristics of mosfet

MOSFET Structure and Operating Regions

MOSFETs, or metal-oxide-semiconductor field-effect transistors, are important parts of electronic circuits. They are used to amplify and switch signals. Their behavior depends on several design features, including channel size, oxide thickness, junction depth, and substrate doping. Channel length and channel width shape how much current a MOSFET can carry and how fast it can switch. Shorter channels usually allow faster operation. The oxide thickness also matters. This silicon dioxide layer...

mosfet: enhancement mode

MOSFET Switching in Enhancement Mode

Enhancement-mode MOSFETs are MOSFETs that work as controlled electronic switches. They belong to the metal-oxide semiconductor field-effect transistor family. These devices come in two forms: n-channel and p-channel, and each one is used for a different polarity of operation. At zero gate-source voltage, or Vgs, an enhancement-mode MOSFET is usually non-conductive. In that default off state, no current flows between the drain and source terminals. When a positive Vgs is applied, it creates an...

mosfet: depletion mode

Depletion MOSFET Channel Control

Depletion-mode MOSFETs are normally on transistors with a built-in channel that conducts current without gate bias. They work differently from enhancement-mode MOSFETs, which need a positive gate-source voltage, or V gs, to turn on. In a depletion device, the channel is already open because the channel doping creates a low-resistance path between the drain and source. These devices behave much like junction field-effect transistors, or JFETs. The channel conductivity is set by the material...

mosfet amplifiers

MOSFET Gain and Biasing

MOSFET gain and biasing shape how a MOSFET amplifier works. When a MOSFET operates in its active region, it acts like a voltage-controlled current source. The gate-to-source voltage sets the drain current, and that behavior supports transconductance amplification. The output current then flows through a load resistor. That load resistor turns the circuit into a voltage amplifier. The output voltage is found by subtracting the voltage drop across the load resistor from the supply voltage, so...

small-signal analysis of mosfet amplifiers

small-signal-analysis-of-mosfet-amplifiers

MOSFET Amplifier Gain and Signal Distortion

MOSFET amplifiers can be treated as linear circuits when they operate in the saturation region. The gate-to-source voltage, or VGS, is the sum of a DC bias voltage and a small time-varying input signal. That bias sets the operating point and controls the drain current that flows from drain to source. When a small AC signal is added at the gate, the drain current has three parts. One part is the DC bias current, ID0, which is the quiescent current with no signal applied. A second part changes...

key terms and concepts

Learn how BJT alpha and beta cut-off frequencies, plus transition frequency, show when transistor gain drops and why high-frequency response changes.

BJT Frequency Limits and Gain Drop | JoVE K12

JoVE Core 電気工学 は、電気回路の基本概念と回路解析テクニックを網羅したアニメーションビデオシリーズです。オペアンプと回路変換および 1 次・ 2 次回路の概念を網羅しています。実験を撮影した実写動画では、設計例や現代社会での応用が含まれており、複雑な概念も分かりやすく学習いただけます。

electrical engineering

BJT Frequency Limits and Gain Drop

Description

Transcript

Tags