Name: concrete wear tests and surface durability
Uploaded: 2024-11-07T14:48:31.000Z
Duration: 1 min 23 s
Channel: JoVE

K12 Standards

Alabama Course of Study Science

9-12

Earth and Space Science

Earth's Systems

9-12.ESS.2.4.b

Abrasion Resistance of Concrete

コンクリートの摩耗は、表面の車両摩耗や水中の研磨性固体から発生する可能性があり、運河の内張りを侵食します。
ショットブラスト試験では、コンクリートサンプルから4インチの90psiの0.25インチノズルから、それぞれASTM No.20サイズに等しい2000個のスチールショットをブラストすることにより、水性固体からのコンクリート侵食を評価します。
回転ディスク試験では、3枚の平板が毎秒0.2サイクルの頻度で円を描くように回転し、各プレートも毎秒4.7サイクルで軸を中心に回転します。炭化ケイ素は、プレートとコンクリートの間の研磨剤として機能します。
鋼球摩耗試験は、回転する頭部に力が加わり、鋼球によってコンクリートから分離され、循環水を用いて摩耗した材料を除去させる試験です。
ドレッシングホイール試験では、サンプルと接触する7つの回転ホイールの3セットに力を加え、駆動ヘッドを毎秒0.93サイクルの周波数で30分間回転させる改造ドリルプレスを使用します。
コンクリート表面の摩耗量は、これらのテストで観察された摩耗の深さによって定量化されます。

コンクリートの耐摩耗性

耐摩耗性はコンクリートの重要な特性であり、さまざまな摩耗条件下での耐久性と寿命を決定します。コンクリート表面は、さまざまな種類の摩耗に対して脆弱です。たとえば、コンクリート運河のライニングに見られるように、表面は車両の絶え間ない移動によって摩耗したり、水中に運ばれた固形物によって侵食されたりすることがあります。コンクリートの耐摩耗性を測定するために、特定の試験が行​​われます。


 こうした試験の 1 つに回転ディスク試験があります。この試験では、研磨材として炭化ケイ素を使用し、3 つのプレートをコンクリートに対して回転させます。もう 1 つは鋼球摩耗試験で、回転する鋼球と水を使用して摩耗プロセスをシミュレートします。3 つ目の試験であるドレッシングホイール試験では、改造したドリルプレスを使用して回転するホイールをコンクリートに押し付けます。これらの試験では、コンクリートの表面の摩耗の深さを測定することで、コンクリートの耐摩耗性を評価します。


 これらの試験の結果は、道路や油圧設備など、日常的な構造物によくある条件下でコンクリートがどの程度耐えられるかを理解するために重要です。耐摩耗性の程度は、一般的にコンクリートの水セメント比と圧縮強度に相関します。耐摩耗性が高いのは、表面層が強く耐久性のあるコンクリートの場合です。最適な耐摩耗性を得るには、適切なコンクリートの仕上げと養生方法が不可欠です。

コンクリートの摩耗は、表面の車両摩耗や水中の研磨性固体から発生する可能性があり、運河の内張りを侵食します。
ショットブラスト試験では、...

Education

JoVE Core

Civil Engineering

土木工学

Unit 1

ユニット1

Strength of Concrete

コンクリートの強度

KEY TERMS AND CONCEPTS

主要用語と概念

concrete wear tests and surface durability

Concrete wear tests show how well a surface can stand up to abrasion and long-term use. Abrasion is the wearing away of a material by rubbing, scraping, or contact with moving solids. This property matters because concrete surfaces can lose material under vehicle traffic or when solids carried in water brush against them.

The transcript describes three tests used to measure concrete abrasion resistance. In the revolving disc test, three plates rotate against the concrete, and silicon carbide acts as the abrasive material. The steel ball abrasion test uses rotating steel balls and water to mimic wear. The dressing wheel test uses a modified drill press that presses rotating wheels against the concrete surface.

These tests measure wear resistance by checking how deep the abrasion reaches into the concrete. The results help show how concrete may perform in roads and hydraulic installations, such as canal linings. Abrasion resistance is often linked with the water-to-cement ratio and compressive strength, and a strong, durable surface layer usually gives better resistance. Proper finishing and curing are important for achieving that kind of surface.

Concrete Wear Tests and Surface Durability

concrete-wear-tests-and-surface-durability

tensile strength considerations of concrete

tensile-strength-considerations-of-concrete

How Cracks Limit Concrete Strength

Concrete tensile strength is limited by tiny cracks inside the material. The cement paste itself can be much stronger in theory than it is in practice. In real concrete, the measured strength can be up to a thousand times lower than the theoretical value. These small cracks help explain that gap. When a load is applied, stress rises at the crack tips. This idea is described by Griffith's theory of brittle fracture. In brittle materials, cracks can grow quickly once the stress at their tips...

behavior of concrete under compressive load

behavior-of-concrete-under-compressive-load

Concrete Failure Patterns Under Compression

Concrete failure patterns under compression show how the material responds to different kinds of direct stress. These patterns help explain concrete’s structural integrity. Under uniaxial compression, where force acts in one direction, cracks often form parallel to the load. These parallel cracks come from local tensile stress, which is pulling stress that appears perpendicular to the compression direction. As uniaxial loading continues, angled cracks may also appear. These cracks are linked...

porosity in cement paste

How Cement Curing Changes Porosity

Cement curing changes porosity in the hardened paste. Porosity means the void spaces inside concrete. These spaces affect both strength and durability. When water and cement react, hydration forms a semi-solid paste that traps water in different ways. Some of that water becomes combined water. It makes up about 23% of the cement's dry mass. Other water stays as gel water, which fills very small voids called gel pores. Gel pores account for about 28% of the cement gel volume. The...

total voids in concrete

Concrete Voids and Strength

Concrete voids affect both strength and permeability. They include gel water, capillary pores, and entrapped air. In hydrated cement paste, gel water is held within the cement hydration products. Physically entrapped or adsorbed water also supports the hydration process. As cement hydrates, the space needed for the products from a cubic centimeter of cement is estimated to double. Capillary pores are the open spaces left inside the hydrated paste. Their size depends mainly on the...

pore size distribution

Concrete Porosity and Durability

Concrete porosity and durability depend strongly on pore size distribution in hardened cement paste. Capillary pores are much larger than gel pores, and in partially hydrated cement paste they form a connected network that lowers strength and raises permeability. Higher permeability makes concrete more vulnerable to freeze-thaw damage and chemical attack. The risk also depends on the water-to-cement ratio. A higher ratio can leave more space for capillary pores to remain open. As cement...

microcracking in concrete

How Concrete Cracks Before Failure

Concrete can develop tiny cracks before any outside load is applied. These microcracks usually form at the boundary between coarse aggregate and hydrated cement paste. They often result from small volume changes caused by stress-strain differences, heat, and moisture movement. At first, these microcracks stay stable. They usually do not grow much until the concrete reaches about 30 percent of its ultimate strength. As the load rises, the material can begin to change more quickly. When...

water cement ratio

Concrete Strength and Water Balance

Concrete strength depends on the balance between water and cement in the mix. This water-cement ratio is the weight of water compared with the weight of cement. It affects strength, durability, and how well concrete resists environmental stress. Abrams’ law shows that less water usually makes stronger concrete. Water is still needed for hydration, which is the chemical process that binds water and cement. It also helps the mix stay workable and compactable. Some water must be absorbed into the...

aggregate cement ratio

How Mix Ratio Changes Concrete Strength

The aggregate cement ratio changes how concrete performs. It is the weight of aggregate divided by the weight of cement in a concrete mix. This ratio affects strength, workability, and durability, so it is an important part of concrete design. A higher aggregate cement ratio makes the mix leaner. Lean mixes have less cement paste to coat and lubricate the aggregate, so they can be harder to work with. At the same time, they may increase strength because the concrete has less total porosity, or...

transition zone

Concrete Transition Zone and Its Porosity

The concrete transition zone is the thin region where aggregate meets cement paste. It has more pores than the surrounding material, so it is usually weaker at first. The bond around the aggregate comes mainly from Van der Waals forces, which are weak attraction forces between particles. When concrete is compacted, this zone often has a higher water-cement ratio near the aggregate. That extra water can form thin water films around the coarse aggregate. These films increase porosity and help...

relation between tensile strength and compressive strength of concrete

relation-between-tensile-strength-and-compressive-strength-of-concrete

Concrete Strength Testing: Tension vs. Compression

Concrete strength testing compares tensile strength and compressive strength. These two properties are related, but they do not rise at the same rate. Tensile strength usually grows more slowly than compressive strength, so the balance between them changes as concrete gets stronger. Several factors affect tensile strength measurements. The test method, specimen size and shape, aggregate texture, and moisture content can all change the result. Direct tension tests are difficult to perform...

fatigue strength of concrete

Concrete Fatigue Under Repeated Loads

Concrete fatigue describes how concrete can weaken or fail when loads are applied again and again, even when each load is below the material’s strength limit. This property matters because it affects the durability and service life of concrete structures. In materials science and engineering, fatigue is a key reason concrete may not last as long as expected under real use. Concrete can fail in two main ways through fatigue. Static fatigue, also called creep rupture, happens under a constant...

impact strength of concrete

Concrete Impact Resistance in Real Use

Concrete impact resistance matters when a material must handle repeated blows and sudden loads. It is important during pile driving, where concrete piles are driven into the ground. It also matters for machinery foundations that experience impulsive loads and for precast concrete parts that can be damaged during handling. Impact strength is measured by checking how well concrete absorbs energy from repeated impacts. A major sign of serious damage is when the concrete does not rebound after...

abrasion resistance of concrete

Concrete wear tests show how well a surface can stand up to abrasion and long-term use. Abrasion is the wearing away of a material by rubbing, scraping, or contact with moving solids. This property matters because concrete surfaces can lose material under vehicle traffic or when solids carried in water brush against them. The transcript describes three tests used to measure concrete abrasion resistance. In the revolving disc test, three plates rotate against the concrete, and silicon carbide...

reinforcements in concrete

Steel Bars in Concrete Structures

Steel bars in concrete structures help the material carry both compression and tension. Concrete is strong when it is squeezed, but it is weak when pulled. Rebar, or reinforcing steel bars, is placed inside the concrete to handle those tensile forces. Steel is a practical choice because it has a similar coefficient of thermal expansion to concrete. That means both materials expand and contract in a similar way as temperature changes. The steel used for reinforcement is usually made by a...

fiber reinforced concrete

Concrete Strength with Added Fibers

Fiber-reinforced concrete is concrete that includes added fibers to improve strength and durability. It uses hydraulic cement with fine or coarse aggregates, plus separated, non-continuous fibers mixed through the material. These fibers can come from steel, glass, and polymers, as well as natural sources such as sisal and cellulose or manufactured sources such as polypropylene and Kevlar. Steel fibers are often preferred because they are strong and tough. They help concrete resist cracking and...

prestressed concrete

How Concrete Is Preloaded for Strength

Prestressed concrete is a construction method that preloads concrete so it can handle more stress. High-strength steel strands are stretched before or after the concrete is loaded in service. The goal is to put the concrete into compression. That compression helps balance the tension the structure will face later. By reducing tension, prestressing helps limit cracks in the concrete. It can also let a structure carry greater loads or span longer distances than conventional reinforced concrete.

ferrocement

Ferrocement Mesh and Mortar Design

Ferrocement is a construction material made from dense layers of mesh or fine rods covered fully in cement mortar. It is a form of reinforced concrete, but it uses mesh instead of the larger steel bars found in standard reinforced concrete. This structure gives ferrocement its thin, flexible form. The material is built from wire meshes and a mortar made of cement and sand. The mortar is usually mixed in a 1:2 or 1:3 ratio. The water-to-cement ratio is kept between 0.40 and 0.45. This helps the...

non-destructive tests for concrete strength

non-destructive-tests-for-concrete-strength

Concrete Strength Checks Without Breaking It

Concrete strength can be checked without fully breaking the material. Two common methods are the rebound hammer test, also called the Schmidt hammer test, and the penetration resistance test, also called the Windsor Probe test. Both are used to estimate the strength of existing concrete. The rebound hammer test measures the hardness of the concrete surface and gives an indirect clue about strength. A spring-driven mass moves inside a tubular housing and strikes a plunger against the concrete.

key terms and concepts

Learn how concrete abrasion resistance is measured with revolving disc, steel ball, and dressing wheel tests, and why surface durability matters in roads and canal linings.

Concrete Wear Tests and Surface Durability | JoVE K12

JoVE Core Civil Engineering provides a foundational exploration of essential construction materials in civil engineering, focusing on bricks, stones, steel, wood, and concrete through easy-to-understand animated videos. This collection covers the properties, manufacturing processes, and practical applications of these materials. Additionally, the accompanied science-in-action videos demonstrate the research experiments performed in laboratories.

civil engineering

physical-properties-of-minerals-i-crystals-and-cleavage

Physical Properties Of Minerals I: Crystals and Cleavage

Source: Laboratory of Alan Lester - University of Colorado Boulder
The physical properties of minerals comprise various measurable and discernible ...

physical-properties-of-minerals-ii-polymineralic-analysis

Physical Properties Of Minerals II: Polymineralic Analysis

Source: Laboratory of Alan Lester - University of Colorado Boulder
The physical properties of minerals include various measurable and discernible ...

Types of Building Stone

Building stones are sourced by extracting rock from natural rock deposits and shaping it into the specific forms and dimensions needed for building ...

4. Obtain, evaluate, and communicate information about the geologic conditions and processes that form different Earth materials.

9-12.ESS.2.4

Igneous Intrusive Rock

Source: Laboratory of Alan Lester - University of Colorado Boulder
Igneous rocks are products of the cooling and crystallization of high temperature ...

Igneous Volcanic Rock

Source: Laboratory of Alan Lester - University of Colorado Boulder
Igneous rocks are the products of cooling and crystallization of magma. Volcanic rocks ...

Quarrying of Stone

Quarrying involves the meticulous extraction of stone from a quarry by either using controlled explosions or precision cutting techniques to remove the ...

a. Plan and carry out investigations to explore the processes that form plutonic (intrusive) and volcanic (extrusive) igneous rocks of differing compositions and textures. Example: Conduct a crystallization experiment to determine how speed of cooling affects crystal size.

9-12.ESS.2.4.a

Acid Attack on Concrete

Acids interacting with concrete dissolve the hydrated cement paste, leading to a softened and structurally weakened material.
Acidity breaks down the ...

Concrete abrasion can occur from vehicular wear on surfaces or abrasive solids in water, which erodes canal linings.
The shot-blast test evaluates ...

turbidity-and-total-solids-in-surface-water

Turbidity and Total Solids in Surface Water

Source: Laboratories of Margaret Workman and Kimberly Frye - Depaul University
Turbidity and total solids are related measurements addressing clarity of ...

b. Analyze and interpret data to explain the effects of mechanical and chemical weathering and erosion on Earth's materials by wind, water, ice, and gravity.

Making a Geologic Cross Section

Source: Laboratory of Alan Lester - University of Colorado Boulder
Geologic maps were first made and utilized in Europe, in the mid-to-late 18th century. ...

c. Construct an explanation using evidence from experiments, models, or data of the processes that create and transform igneous, sedimentary, and metamorphic rocks.

9-12.ESS.2.4.c

Pore Size Distribution

Capillary pores are considerably larger than gel pores, and various pore sizes exist within the hardened cement paste.
In conditions of partial hydration, ...

determination-of-moisture-content-in-soil

Determination of Moisture Content in Soil

Source: Laboratories of Dr. Ian Pepper and Dr. Charles Gerba - The University of Arizona
Demonstrating Author: Bradley Schmitz
Soils normally contain a ...

Non-destructive Tests for Concrete Strength

Non-destructive tests, such as the rebound hammer test and penetration resistance test, can be used to determine the strength of concrete in an existing ...

d. Plan and conduct an investigation on water's effect on surface and subsurface processes. Examples: Use particles of varying sizes to determine how the speed of water impacts particle distribution. Use the porosity and permeability of particles of various sizes to determine how the size and sorting of particles affects water movement.

9-12.ESS.2.4.d

gis-software-hardware-and-sources-of-gis-data

GIS Software, Hardware, and Sources of GIS Data

A Geographic Information System (GIS) combines specialized software and hardware to effectively manage, analyze, and present spatial and related data. GIS ...

Manipulation and Analysis

GIS manipulation and analysis functions are vital for decision-making and planning. These activities range from data retrieval tasks, such as selecting ...

Using GIS to Investigate Urban Forestry

Source: Laboratories of Margaret Workman and Kimberly Frye - Depaul University
Urban forests broadly include urban parks, street trees, landscaped ...

e. Obtain and communicate information about significant geologic characteristics in Alabama and the southeastern United States. Examples: types of rocks, caves, sinkholes, minerals, energy resources

9-12.ESS.2.4.e

The Fossil Record

The fossil record documents only a small fraction of all organisms that have ever inhabited Earth. Fossilization is a rare process, and most organisms ...

The Evidence for Evolution

Genetic variations accumulating within populations over generations give rise to biological evolution. Evolutionary changes can result in the formation of ...

5. Obtain, evaluate, and communicate information about major events in Earth's history.

9-12.ESS.2.5

Radioactive Decay and Radiometric Dating

Radioactivity is a spontaneous disintegration of an unstable nuclide and is a random process, as all the nuclei in the sample do not decay simultaneously. ...

Isotopes

Elements have a set number of protons that determines their atomic number (Z). For example, all atoms with eight protons are oxygen; however, the number ...

a. Analyze and interpret data to sequence events in Earth's history, including relative and absolute dating techniques, principles of superposition and crosscutting relationships, igneous intrusions, radiometric dating, and the fossil record.

9-12.ESS.2.5.a

Extinction

The History of Life on Earth
Fossils of organisms that were different from anything alive today had been documented as early as the 17th century, but it ...

b. Construct an explanation based on evidence of how catastrophic and long-term events have impacted life on Earth, including mass extinctions.

9-12.ESS.2.5.b

The Colonization of Land

Changes in the environment of the early Earth drove the evolution of organisms. As prokaryotic organisms in the oceans began to photosynthesize, they ...

The Carbon Cycle

Carbon is the basis of all organic matter on Earth, and is recycled through the ecosystem in two primary processes: one in which carbon is exchanged among ...

What is Photosynthesis?

Photosynthesis is a multipart, biochemical process that occurs in plants as well as in some bacteria. It captures carbon dioxide and solar energy to ...

c. Construct explanations from evidence of how the flow of energy through Earth's systems has changed over time. Example: Earth's oxygen level was lowest during the Cryptozoic Eon (Precambrian) and highest in the Carboniferous.

9-12.ESS.2.5.c

an-overview-of-bgdgt-biomarker-analysis-for-paleoclimatology

An Overview of bGDGT Biomarker Analysis for Paleoclimatology

Source: Laboratory of Jeff Salacup&#160;- University of Massachusetts Amherst
Throughout this series of videos, natural samples were extracted and ...

an-overview-of-alkenone-biomarker-analysis-for-paleothermometry

An Overview of Alkenone Biomarker Analysis for Paleothermometry

d. Obtain, evaluate, and communicate information about important tectonic and geologic events that have occurred in Alabama over geologic time. Examples: geologic ages and types of rocks, fluctuations in sea levels, temperature changes

9-12.ESS.2.5.d

determining-spatial-orientation-rock-layers-with-brunton

Determining Spatial Orientation of Rock Layers with the Brunton Compass

Source: Laboratory of Alan Lester - University of Colorado Boulder
Most rock units exhibit some form of planar surfaces or linear features. Examples ...

Properties of Transition Metals

Transition metals are defined as those elements that have partially filled d orbitals. As shown in Figure 1, the d-block elements in groups 3&#8211;12 are ...

6. Obtain, evaluate, and communicate information about the theory of plate tectonics.

9-12.ESS.2.6

a. Construct an evidence-based explanation of continental drift, basing conclusions on comparisons of coastlines, fossils, ages of rocks, climate, and magnetic patterns.

9-12.ESS.2.6.a

b. Construct an explanation, based on evidence, of tectonic plate movement, types of plate boundaries, and how boundary type relates to specific tectonic features, including mountain ranges, earthquakes, volcanism, volcanic islands, hotspots, mid-ocean ridges, and faults.

9-12.ESS.2.6.b

c. Develop and interpret a model of Earth's internal structure and composition, including inner core, outer core, asthenosphere, lithosphere, mantle, and crust.

9-12.ESS.2.6.c

d. Analyze data to interpret seismic activity and assess the risk of volcanic eruptions and earthquakes in Alabama and other areas in the United States.

9-12.ESS.2.6.d

applications-of-gis-disaster-management-and-emergency-response

Applications of GIS: Disaster Management and Emergency Response

Geographic Information System (GIS) technology is essential for risk identification, action prioritization, and resource optimization in critical ...

Coordinates and Map Projections

Coordinates and map projections are essential tools in accurately representing the Earth's surface for various applications, ranging from navigation to ...

Mechanisms of Heat Transfer I

Just as interesting as the effects of heat transfer on a system are the methods by which the heat transfer occur. Whenever there is a temperature ...

Mechanisms of Heat Transfer II

In convection, thermal energy is carried by the large-scale flow of matter. Ocean currents and large-scale atmospheric circulation, which result from the ...

Heat Flow and Specific Heat

Heat is a type of energy transfer that is caused by a temperature difference, and it can change the temperature of an object. Since heat is a form of ...

conduction-convection-and-radiation-problem-solving

Conduction, Convection and Radiation: Problem Solving

There are three methods by which heat transfer can take place: conduction, convection, and radiation. Each method has unique and interesting ...

The Water Cycle

The Earth&rsquo;s hydrosphere includes all of the areas where the storage and movement of water occurs. Since water is the basis of all living processes, ...

phase-transitions-vaporization-and-condensation

Phase Transitions: Vaporization and Condensation

The physical form of a substance changes on changing its temperature. For example, raising the temperature of a liquid causes the liquid to vaporize ...

Phase Changes

Phase transitions play an important theoretical and practical role in the study of heat flow. In melting or fusion, a solid turns into a liquid; the ...

7. Obtain, evaluate, and communicate information about the role of energy transfer in wind, precipitation, cloud formation, and front formation.

9-12.ESS.2.7

Concrete Wear Tests and Surface Durability

Description

Transcript

More videos by Standards