Name: static and kinetic dry friction
Uploaded: 2023-09-22T11:49:28.000Z
Duration: 1 min 21 s
Channel: JoVE

정원사가 손수레를 밀고 있다고 생각해 보십시오. 카트를 움직이기 위해 힘이 가해지면 바퀴와 지면 사이에 건조 마찰이 발생합니다.
정적 마찰력은 접촉면에 접선으로 작용하며, 움직임을 일으키려는 힘과 반대입니다.
수레가 미끄러지려고 할 때 계면의 최대 정적 마찰력은 수직력에 비례합니다. 여기서 정적 마찰 계수는 접촉하는 재료의 유형과 표면의 거칠기에 따라 달라집니다.
정적 마찰력은 정상 압력이 접촉면에 변형이나 손상을 일으키지 않는 특정 범위 내에 있을 때만 접촉 영역과 무관합니다.
수레가 미끄러지기 시작하면 개발된 운동 마찰력은 수직력에 비례합니다.
일반적으로 최대 정적 마찰력보다 낮습니다. 그러나 카트가 표면 위에서 매우 낮은 속도로 움직이면 거의 같아집니다.
운동 마찰 계수는 일반적으로 재료의 표면 특성과 주변 환경에 따라 달라집니다.

<ol>
	<li>히벨러, R.C. (2016). 엔지니어링 역학: 정적. 14판, 뉴저지: 피어슨. 405쪽.</li>
	<li>Meriam, J.L., Kraige, L.G. 및 Bolten, J.N.(2016). Engineering Mechanics: Statics and Dynamics(정역학 및 동역학). 여덟 번째 판, 싱가포르 : John Wiley & Sons. 336쪽.</li>
</ol>

건마찰의 특성

Characteristics of Dry Friction

건마찰은 윤활이나 유체가 전혀 없는 상태에서 두 고체 표면이 서로 미끄러질 때 발생합니다. 마치 정원사가 손수레를 밀듯이 표면을 따라 물체를 밀 때 저항을 일으킵니다. 수레를 움직이기 위해 가해지는 힘은 바퀴와 지면 사이에 건마찰을 일으킵니다. 
바퀴살이 움직이기 시작하기 전에 정지 마찰력은 접촉면에 접선으로 작용하여 운동을 유도하려는 힘과 반대로 작용합니다. 이 마찰력은 바퀴살이 미끄러지는 것을 방지하고 안정성을 유지하는 데 도움이 됩니다. 두 표면 사이에 상대적인 움직임이 없을 때만 정지 마찰력이 존재한다는 점에 유의해야 합니다.
손수레가 미끄러지려고 할 때, 접점에서의 최대 정적 마찰력은 수직력에 정비례합니다. 이 관계는 접촉하는 물질의 종류와 표면의 거칠기에 따라 결정되는 정지 마찰 계수에 의해 정의됩니다.
흥미롭게도 정상압력이 접촉면의 변형이나 손상을 피할 수 있는 특정 범위 내에 있을 때 정지 마찰력은 접촉 면적과 무관합니다. 이는 바퀴와 지면의 접촉 면적이 변하더라도 정상압력이 이 특정 범위 내에 유지되는 한 정적 마찰력은 일정하게 유지된다는 것을 의미합니다.
일단 손수레가 미끄러지기 시작하고 움직임이 발생하면 개발된 운동 마찰력이 작용합니다. 이 힘도 정상적인 힘에 비례하지만 일반적으로 최대 정지 마찰력보다 낮습니다. 두 힘의 차이는 상대 운동을 하는 표면이 서로 맞물려 저항을 만드는 시간이 적기 때문이라고 할 수 있습니다.
하지만 손수레가 표면 위에서 매우 낮은 속도로 움직이면 운동 마찰력은 최대 정적 마찰력과 거의 같아집니다. 느린 움직임은 표면 사이의 상호 작용을 더 많이 허용하여 저항을 증가시키기 때문입니다.
운동마찰계수는 주로 물질의 표면 특성과 주변 환경에 따라 결정됩니다. 온도, 습도, 표면 오염 등의 요인이 운동마찰력에 큰 영향을 미칠 수 있습니다.
정지마찰과 운동마찰의 계수에 영향을 미치는 요인을 조사함으로써 접촉하는 물질과 표면의 거칠기, 주변 환경 사이의 관계를 더 잘 이해할 수 있습니다. 이러한 이해를 통해 특정 응용 분야의 물질을 설계하고 선택할 때 개인이 정보에 입각한 결정을 내릴 수 있으며, 궁극적으로 다양한 시스템과 장치의 성능과 기능을 향상시킵니다.

건조 마찰은 두 개의 단단한 표면이 윤활제나 유체가 없는 상태에서 서로 미끄러질 때 발생합니다. 물체를 밀 때 저항을 일으킵니다 ...

Education

교육

JoVE Core

Mechanical Engineering

기계공학

Unit 1

제1단원

Friction

마찰

KEY TERMS AND CONCEPTS

주요 용어 및 개념

static and kinetic dry friction

Dry friction is the resistance between two solid surfaces that move against each other without lubrication or any fluid. A common example is a gardener pushing a wheelbarrow across the ground. The wheel and the ground create dry friction that slows the motion.

Before the wheelbarrow starts to move, static friction acts at the contact surface. Static friction is the force that opposes motion before slipping begins, and it helps keep the wheelbarrow stable. It is present only when there is no relative motion between the two surfaces.

As the wheelbarrow is about to slip, the maximum static friction depends on the normal force. The normal force is the push that surfaces exert on each other at the contact point. This maximum static friction is described by the coefficient of static friction, which depends on the materials in contact and on how rough their surfaces are.

Static friction also does not depend on contact area when the normal pressure stays within a range that avoids deformation or damage. So, even if the wheel and the ground touch over a larger or smaller area, the static friction can stay the same under those conditions. Once the wheelbarrow begins to slide, kinetic friction takes over.

Kinetic friction is the friction force during motion. It is also proportional to the normal force, but it is usually smaller than the maximum static friction. At very low speed, however, kinetic friction can become nearly equal to the maximum static friction because the surfaces have more time to interact.

The coefficient of kinetic friction mainly depends on surface properties and the surrounding environment. Temperature, humidity, and surface contamination can change its value. Knowing how static and kinetic friction respond to material type, surface roughness, and environmental conditions helps in choosing the right materials for different uses.

Static and Kinetic Dry Friction

dry friction

Dry Friction in Crates and Everyday Motion

Dry friction appears when two solid surfaces touch and try to move past each other. Students can see it when they walk, slide a box across a table, or rub their hands together. Even though it is common, the forces behind it are not easy to see. A simple crate on a rough horizontal floor helps explain the idea. When an external force pushes the crate sideways, two main forces act on it. The normal force acts perpendicular to the surface and helps balance the crate’s weight, while the frictional...

static friction

Static Friction at the Point of Slip

Static friction is the force that keeps two surfaces from starting to slide past each other. It acts when there is a tendency for motion, but not yet actual slipping. This force helps explain everyday actions like walking on the ground and driving a car. A towing example shows how static friction changes as force is applied. A truck pulls a car with a rope, and the car stays still at first. The car is in static equilibrium, which means the forces on it are balanced. Gravity and the normal...

kinetic friction

Sliding Friction Between Moving Surfaces

Kinetic friction is the sliding friction that acts when two surfaces move against each other. It opposes relative motion and acts parallel to the contact surface, in the opposite direction of travel. In the truck and car example, the car first stays still because static friction holds it in place. When the truck’s force becomes greater than the limiting static frictional force, the friction at the contact surface drops to a lower value. The car then begins to slide, and its speed increases. At...

characteristics of dry friction

Dry friction is the resistance between two solid surfaces that move against each other without lubrication or any fluid. A common example is a gardener pushing a wheelbarrow across the ground. The wheel and the ground create dry friction that slows the motion. Before the wheelbarrow starts to move, static friction acts at the contact surface. Static friction is the force that opposes motion before slipping begins, and it helps keep the wheelbarrow stable. It is present only when there is no...

types of friction problems

Dry Friction in Crate, Ladder, and Frame Problems

Dry friction problems often focus on crates, ladders, and frames that are close to slipping. Dry friction is the force that resists relative motion, or the tendency for motion, between two surfaces in contact. In many physics and engineering problems, this force helps keep an object still or defines the point where motion is about to begin. One common case has no clear impending motion. A force may be applied to a crate, but the crate stays at rest. The friction force between the floor and the...

friction: problem solving

Friction on a Banked Road

Friction on a banked road affects whether a bus stays steady while it moves at constant speed. In this problem, a bus with a mass of three megagrams travels on a sloped road. The coefficient of static friction between the tires and the road is 0.5. The goal is to find the maximum bank angle where the bus will not slip or tip. To solve the motion part, the forces on the bus must be shown first. These include gravity, the normal force, and friction. The normal force is the push from the road,...

wedges

Wedges and Self-Locking Stability

A wedge is a simple machine that can lift, support, and split heavy objects. It can also change the height of structural or mechanical parts. Because it amplifies force, a wedge makes it easier to move or hold large loads with less effort. One example is lifting a heavy slab. In that case, the wedge turns the applied force into a much larger force that acts almost perpendicular to the original push. That force change helps raise the load without requiring a large input force. To analyze wedge...

frictional forces on screws

Square-Thread Screw Mechanics and Friction

Square-threaded screws use a helical thread to turn force into lifting motion. They are common fasteners, but they are also useful for transmitting power and motion in machines. A jack with a square-threaded screw lifts heavy loads when force is applied at the handle and the screw turns. A screw can be viewed as a cylindrical shaft with an inclined square ridge wrapped around it. The distance between two neighboring threads is called the pitch. The lead is the distance the screw advances in...

upward impending motion

Screw Jack Force and Friction Analysis

A square-threaded screw jack lifts heavy loads by turning handle force into a twisting moment. Its upward motion depends on overcoming static friction between the screw threads and the jack. To study this motion, the thread can be treated as if it were a block on the groove of the jack after the thread is completely unraveled. A free-body diagram helps show the forces acting on this simplified system. The force at the handle creates a horizontal force that pushes the movable thread up the...

self-locking screw

Screw Jack Self-Locking Behavior

A square-threaded screw jack can hold a heavy load because of its self-locking behavior. This feature makes the device more reliable when it is used to lift large weights or apply a strong force. If the screw keeps its position after the turning moment is removed, the jack is self-locking. Self-locking happens because friction changes the way the forces act on the thread. The friction force reverses direction, and the reaction force moves to the other side of the thread’s normal. In this case,...

screw: problem solving

Screw Torque and Self-Locking

Screw torque and self-locking are analyzed by looking at a threaded screw shaft and a plate gear. The shaft has a mean radius and a lead. The plate gear also has a mean radius. The coefficient of static friction between the screw and the gear is part of the setup. The first step is to find the static friction angle, φ. This angle is defined by the coefficient of static friction. Next, the lead angle is calculated from the lead and the mean radius of the shaft. It gives the screw geometry...

frictional forces on flat belts

Flat Belt Tension and Friction

Flat belt tension and friction control how power moves from one pulley to another. Flat belts are used in many industrial systems to transmit power between pulleys. As the belt wraps around the pulleys, the tension changes because of friction between the belt and the pulley surface. When a pulley turns counterclockwise, the belt side moving away from the pulley has the higher tension, called T2. The side moving toward the pulley has the lower tension, called T1. To estimate these tensions, the...

flat belts: problem solving

Flat Belt Forces and Pulley Moment

Flat belts transmit power from one pulley to another, and the forces on the belt help determine the moment on a pulley. In this example, a belt wraps around pulleys A and B, with radii of 30 cm and 10 cm. The belt meets the pulleys at a 20 degree angle from the horizontal, which sets up the force balance in the system. As pulley B rotates clockwise, it drives pulley A. That motion creates tension T2 on one side of the belt and tension T1 on the other side. The belt-to-surface contact angle, β,...

pivot bearings

Axial Load Support in Pivot Bearings

Pivot bearings support axial loads on a rotating shaft. A bearing helps two parts move relative to each other while reducing friction and wear. In this design, the pivot is placed at the end of the shaft to carry the axial thrust. The pivot surface can be flat, conical, or truncated, depending on the application. In a flat pivot bearing, the axial load is spread over the bearing area. The pressure is uniform and can be found by dividing the load by the area. To study the forces more closely,...

collar bearings

Friction Torque in Collar Bearings

Collar bearings support axial loads on rotating shafts, and their friction helps determine the torque needed to start motion. They are used in many machines and may have a single collar or multiple collars, depending on the application and load needs. For a single collar bearing under an axial load, the contact area is the ring-shaped region between the external radius and the internal radius of the collar. If the bearing is assumed to support the load evenly, the uniform normal pressure is...

journal bearings

Friction Moment in Journal Bearings

Journal bearings support rotating shafts and axles while helping keep them stable. They are used in machines such as engines, turbines, and pumps. Their job is to reduce friction, wear, and vibration. A journal bearing works by keeping a thin film of lubricant between the bearing surface and the rotating shaft. This film limits direct contact and lowers frictional force. The video uses a rope winch with dry or only partly lubricated journal bearings to show the idea. As the spool turns...

bearings: problem solving

Double-Collar Bearing Torque Calculations

Double-collar bearing torque calculations show how friction and axial force affect bearing performance. Engineers use these calculations to test whether the bearing can handle the forces and moments it experiences during operation. This helps them choose and design bearings for specific applications and setups. For a double-collar bearing with set dimensions and an axial force applied, the maximum frictional moment can be found with a standard expression. The equation is rearranged, and the...

rolling resistance

Tire Deformation and Rolling Resistance

Tire deformation and rolling resistance explain why a rolling wheel still needs a driving force. When a solid cylinder or tire rolls on a rigid surface, the normal force is perpendicular to the surface at the contact point. But real materials are not perfectly rigid, so the surface pushes back with a spread of normal pressures instead of one single force. A hard cylinder on a softer surface compresses the material under it. As the cylinder moves forward, the material in front of the contact...

rolling resistance: problem solving

Lawn Roller Force Calculation

Rolling resistance is the force that makes a rolling object harder to move across a surface. It is also called rolling friction. It comes from deformation in the object and the surface that touch each other. Internal friction, hysteresis, and other energy losses in the materials also play a role. Because of this force, extra energy is needed to keep a wheel, tire, or ball moving. The video applies this idea to a lawn roller. The roller has a mass of 100 kg, a radius of 25 cm, and a coefficient...

key terms and concepts

Explore dry friction in high school physics, including static friction, kinetic friction, normal force, material roughness, and how environment affects motion.

Static and Kinetic Dry Friction | JoVE K12

JoVE Core Mechanical Engineering offers concise, easy-to-understand animated videos covering key topics such as equilibrium, forces, truss analysis, and structural mechanics. Explore their real-world applications, and witness these concepts in action through scientist-led experiments.

mechanical engineering

Static and Kinetic Dry Friction

Description

Transcript