Name: preparing samples by state and form
Uploaded: 2024-12-05T18:31:54.000Z
Duration: 1 min 21 s
Channel: JoVE

샘플 준비는 정확한 분석 결과를 얻기 위한 중요한 단계입니다. 이는 추출, 정제 및 농축의 세 가지 주요 목표로 구성됩니다.
첫째, 추출에는 샘플 매트릭스에서 관심 분석물과의 혼합물을 분리하는 작업이 포함됩니다. 둘째, 간섭 물질이 존재하는 경우 순수한 샘플을 얻기 위해 제거합니다. 셋째, 추출된 분석물의 농도가 낮으면 정확하게 검출할 수 있는 수준으로 농축됩니다.
샘플의 일반적인 형태는 고체, 액체 및 기체입니다. 너무 커서 직접 분석할 수 없는 고체 덩어리는 연삭, 분쇄 및 밀링과 같은 물리적 방법으로 분말화됩니다.
이 혼합물을 체질하고 혼합하면 균일한 미세 분말이 생성되며, 이 분말은 건조되고 적절한 용매에 용해되어 분석물을 용액으로 추출합니다. 
고체와 달리, 액체 현탁액은 불순한 고체 입자를 제거하기 위해 분석 전에 여과되거나 원심분리됩니다.
고체 흡착제는 기체 분석물을 선택적으로 흡착하기 때문에 기체에 대한 시료 전처리가 필요하지 않습니다.

분석을 위한 표본 준비: 개요

표본 준비는 분석 과정에서 필수적인 단계입니다. 여기에는 표본을 준비하여 정확하게 분석할 수 있도록 하는 것이 포함됩니다. 목표는 분석을 방해할 수 있는 모든 구성 요소를 제거하는 동시에 표본에서 측정하려는 물질인 분석물을 추출하는 것입니다. 표본 준비 기술은 표본의 물리적 상태에 따라 다릅니다.

대량 또는 대형 고체 표본은 일반적으로 분쇄, 파쇄 또는 밀링 기술을 사용하여 크기를 줄여 표본 표면적을 늘리고 보다 효율적인 분석을 제공합니다. 분쇄 후 표본을 체질하고 혼합하여 균일한 구성을 보장합니다. 그런 다음 분말 표본을 적절한 용매에 용해하여 고체 매트릭스에서 분석물을 추출합니다. 용매 선택은 분석물의 특성과 표본 구성 요소의 용해도 특성에 따라 달라집니다.

부유 고체 입자 또는 침전물을 포함하는 액체 표본은 일반적으로 여과 또는 원심 분리를 거쳐 고체 불순물을 액체에서 분리합니다. 여과는 액체를 필터로 통과시키는 반면, 원심분리는 원심력(회전)을 사용하여 고체와 액체상을 분리합니다. 분석물이 미량으로 존재하는 경우, 액체 표본은 농축 단계의 전처리를 거쳐 분석물 농도를 높여 더 나은 검출을 위해 증가시킵니다.

가스 표본을 분석 장비에 직접 도입할 수 있으므로 가스 분석물을 분석하는 데는 일반적으로 표본 준비가 필요하지 않습니다.

샘플 준비는 분석 공정에서 필수적인 단계입니다. 여기에는 정확하게 분석할 수 있도록 샘플을 준비하는 작업이 포함됩니다. 목표는 ...

Education

교육

JoVE Core

Analytical Chemistry

분석 화학

Unit 1

제1단원

Method Development and Sampling Techniques

분석법 개발 및 시료 채취 기술

method-development-and-sampling-techniques

KEY TERMS AND CONCEPTS

주요 용어 및 개념

Sample Preparation for Analysis: Overview

preparing samples by state and form

Sample preparation depends on the state and form of the sample before analysis. It helps make the sample ready for accurate measurement. The main goal is to extract the analyte, which is the substance being measured, and remove parts that could interfere with the analysis.

Solid samples often need the most handling. Large solids are usually ground, crushed, or milled to make them smaller and increase surface area. The sample is then sieved and mixed so it has a uniform composition. After that, the powdered material is dissolved in a suitable solvent to pull the analyte out of the solid matrix. The best solvent depends on the analyte and on how well the sample components dissolve.

Liquid samples may also need treatment before analysis. If they contain suspended solids or precipitates, they are usually filtered or centrifuged to remove the unwanted particles. Filtration works by passing the liquid through a filter. Centrifugation uses spinning force to separate the solid material from the liquid phase.

When the analyte is present in trace amounts, liquid samples may need a concentration step. This increases the analyte level so it is easier to detect. Sample preparation is usually not needed for gaseous analytes because the gas sample can be introduced directly into the analytical instrument.

Preparing Samples by State and Form

development of analytical methods

Analytical Methods: Technique to Protocol

Analytical methods follow a clear path from technique to protocol. In analytical chemistry, a technique is the scientific principle used to explain a chemical measurement. A method applies that technique to a sample of interest. The next steps are procedure and protocol. A procedure gives the directions for carrying out the analysis with an analytical method. A protocol is the detailed set of guidelines for that procedure, and it should be followed closely to get the desired results. <br...

quality control

Quality Control Charts and Lab Records

Quality control charts, proficiency testing, and lab records are key parts of quality control in a laboratory. These steps help keep a system under statistical control. They also help track data, show trends, and spot variations that may affect the accuracy of an analysis. One common tool is a quality control chart. This chart plots one or more analytical characteristics over time. The measured values are taken at different times during the analysis and compared with the known value of...

quality assurance

Quality Checks in Analytical Testing

Quality assurance in analytical testing brings together the checks that help a system perform properly. It includes quality control, quality assessment, and internal corrective measures. These parts work in a cycle to support reliable results. Quality control happens before and during the analysis. Quality assessment takes place during and after the investigation. Internal corrective measures are then based on the results of post-analysis quality assessment, or they may be applied before a new...

data validation

How Analytical Methods Are Checked

Method validation checks whether an analytical chemistry method gives reliable results. It is especially important when the same method is used with different sample matrices or when the procedure is changed. Validation helps show that the method still meets acceptable standards in each case. Several key checks are used in method validation. Specificity means the method can measure the target analyte without interference from other substances. Linearity means the result changes in direct...

qualitative analysis

Classical and Instrumental Sample ID

Qualitative analysis identifies the elements, ions, or compounds in an unknown sample. It is the first step in the hierarchy of analytical goals. That makes it the starting point for scientific study before quantitative analysis or other forms of analysis. Two main approaches are used in qualitative analysis: classical methods and instrumental methods. Classical methods depend on the visible or sensory result of a chemical reaction, such as a color change, a precipitate, or even a smell. These...

quantitative analysis

Measuring Analyte Concentration

Quantitative analysis measures the amount of a specific substance, called the analyte, in a sample. If the sample composition is unknown, qualitative analysis comes first. That step identifies the components so the correct substances can be measured during the quantitative phase. This method depends on two key measurements. Scientists measure the sample quantity and also a property that is proportional to the amount of analyte. Together, these measurements help determine the analyte...

instrument calibration

Calibrating Lab Instruments for Accurate Results

Calibration helps lab instruments produce accurate and consistent results. It is important in manufacturing, healthcare, testing laboratories, and scientific research. Each instrument needs a calibration process that matches its design and function. This process improves data accuracy and helps results stay reliable. An analytical balance measures mass and needs regular calibration to stay precise. It is calibrated by comparing its readings with known standard weights. These weights act as...

glassware calibration

Calibrating Lab Glassware for Accurate Volume

Calibrating lab glassware helps students measure liquids accurately in the analytical laboratory. It reduces volume errors and supports consistent results across measurements. This matters when using volumetric flasks, pipettes, burettes, and other tools that depend on precise volume readings. Volumetric flasks are used to prepare aqueous solutions with a precise final volume. They have a calibration line on the neck. To calibrate one, fill it with distilled water until the meniscus, the...

standard solutions

Preparing Standard Solutions in the Lab

Standard solutions are prepared to have a precisely known concentration or composition. In analytical chemistry, this accuracy is important because it supports reliable results. A primary standard is a highly pure, stable substance with a high molar mass. It is fully soluble in water, which is the most commonly used solvent in analytical chemistry. A primary standard solution can be used to standardize a secondary standard. Secondary standards have known concentrations, but they are usually...

blank solutions

Blank Solutions in Analytical Testing

Blank solutions are used in analytical testing to show the background signal before a sample is measured. A blank solution does not contain the analyte, which is the substance of interest being tested or measured. It is usually made with the same reagents and procedure as the sample solution, but without the analyte. The main purpose of a blank solution is to control for background interference and contamination. Reagents, solvents, or lab equipment can sometimes create a detectable signal on...

sampling methods: overview

How Sampling Shapes Lab Results

Sampling shapes lab results by determining how a smaller sample represents a larger population. In analytical chemistry, testing an entire population is often impractical or impossible, so samples are collected to make inferences about the whole group. The sampling method is the process used to choose individuals or items for that sample. Common sampling methods include random, judgemental, systematic, stratified, and cluster sampling. Each method can affect the quality of the data in a...

sampling methods: sample types

Sampling Materials in Solid, Liquid, Gas

Sampling materials are grouped as solid, liquid, or gas. The type of sample helps decide the right collection method. Solid samples can include sediments from water bodies, soil, metals, and biological tissues. Sediment sampling from water bodies can be done in two common ways. Grab sampling uses a device to collect a discrete sample from the bottom with minimal disturbance. These samples may not show the full area because conditions can vary from place to place. Piston coring collects a...

sampling plans

Choosing Samples for Reliable Results

Sampling is a key step in analytical chemistry. It helps researchers collect data that represents a larger population. The main sampling methods in this topic are random, judgmental, systematic, stratified, and cluster sampling. Random sampling gives each member of the population an equal chance of being chosen. Researchers often use a random number generator or a lottery-style method. For example, a polymer sheet can be divided into 1 cm x 1 cm sections, and 10 sections can be selected at...

sample preparation for analysis: overview

Sample preparation depends on the state and form of the sample before analysis. It helps make the sample ready for accurate measurement. The main goal is to extract the analyte, which is the substance being measured, and remove parts that could interfere with the analysis. Solid samples often need the most handling. Large solids are usually ground, crushed, or milled to make them smaller and increase surface area. The sample is then sieved and mixed so it has a uniform composition. After that,...

sample preparation for analysis: advanced techniques

sample-preparation-for-analysis-advanced-techniques

Preparing Complex Samples for Analysis

Preparing complex samples for analysis often requires special digestion and fusion methods. Samples with inorganic or organic material can be hard to dissolve or break down. Common sample preparation methods include acid digestion, fusion, dry ashing, and wet digestion. These steps help turn difficult samples into forms that can be tested reliably and again with similar results. Acid digestion is often used for inorganic materials that do not dissolve in water. It is useful for soil and...

sample handling

Sample Transport and Storage Basics

Sample transport and storage help keep specimens intact before testing. Moving a sample from the collection point to the laboratory requires careful handling. The sample should be sealed well and clearly labeled. These steps help prevent cross-contamination and support reliable results. Temperature control is also important during transport. Some samples travel in insulated containers, cool packs, or refrigerated vehicles so they stay within the needed temperature range. After the samples...

contaminants and errors

Sampling Errors in Sample Preparation

Sampling errors in sample preparation can affect the accuracy of laboratory results. Two common problems are concentration bias from poor sample splitting and contamination from reducing particle size by grinding or homogenization. Recognizing these errors helps make analysis more reliable. The number of samples also matters when a target population follows a normal distribution. In that case, the sample size ns can be found with a formula that uses the t-value for the chosen confidence level,...

key terms and concepts

Learn how sample preparation changes for solids, liquids, and gases, including grinding, filtering, centrifuging, and concentration steps for accurate analysis.

Preparing Samples by State and Form | JoVE K12

analytical chemistry

JoVE Core Analytical Chemistry simplifies complex chemical principles by breaking them down into clear, engaging animations, making topics from SI Units to NMR spectroscopy more accessible and straightforward. Additionally, the scientist-in-action videos highlight the application of these concepts in real-world research conducted in laboratories globally.

Preparing Samples by State and Form

Description

Transcript

Tags