Name: raman spectroscopy setup and detectors
Uploaded: 2024-12-05T18:32:10.000Z
Duration: 1 min 26 s
Channel: JoVE

라만 분광 광도계에는 레이저 소스, 샘플 홀딩 시스템, 파장 선택기 및 검출기의 네 가지 핵심 구성 요소가 있습니다.
레이저 소스는 일반적으로 가시광선 또는 근적외선 범위의 단색광의 집중된 빔을 방출하며, 그 중 일부는 샘플의 분자에 의해 산란됩니다.
샘플은 액체, 용액, 투명 고체, 분말, 펠릿 또는 가스를 포함한 다양한 형태일 수 있습니다.
산란된 빛은 선택된 개별 파장을 제외한 모든 파장을 제외한 모노크로메이터를 통해 수집되고 지시됩니다. 
광학 대역 제거 또는 '노치' 필터는 라만 신호를 방해할 수 있는 표유 레이저 방사선 및 레일리 산란에서 빛을 제거합니다.
특히 광섬유 라만 분광기는 고품질 대역 통과 및 노치 필터를 사용하여 검출기에 도달하는 레일리 산란 방사선을 최소화합니다.
검출기(종종 전하 결합 장치 또는 광전자 증배관)는 광 신호를 전기 신호로 변환하여 라만 스펙트럼을 생성합니다.
푸리에 변환 라만 기기는 모노크로메이터 대신 마이컬슨 간섭계와 함께 연속파 레이저 소스를 사용하며, 방사선은 분석을 위해 냉각된 포토다이오드에 집중됩니다.

라만 분광법: 계측

Raman Spectroscopy Instrumentation: Overview

기존의 라만 분광 광도계에는 레이저 소스, 표본 보관 시스템, 파장 선택기 및 검출기가 포함됩니다.

일반적으로 가시광선 또는 근적외선 복사를 사용하는 단색 레이저 소스는 고도로 집중된 광선을 생성합니다. 이 빛은 표본 분자와 상호 작용하여 일부 빛을 산란시킵니다. 액체 및 기체 표본은 일반적으로 일반 유리 모세관에서 검사하는 반면 고체는 모세관에 포장된 분말 또는 브롬화 칼륨 펠릿으로 분석할 수 있습니다. 산란된 빛은 별도의 렌즈를 사용하여 수집되어 단색화장치 입구에 초점을 맞추고, 단색화장치는 빛을 구성 주파수로 분산시킵니다.

정확한 결과를 보장하기 위해 출력은 광범위하게 필터링되어 라만 신호를 방해할 수 있는 스트레이 레이저 복사 및 레이리 산란을 제거합니다. 그런 다음 광학 신호는 종종 전하 결합 소자 또는 광전 증배관인 검출기 내에서 전기 신호로 변환되어 라만 스펙트럼으로 처리 및 시각화할 수 있습니다.

어떤 경우에는 레일리 산란 복사선을 최소화하기 위해 광섬유 라만 분광기에서 고품질 대역 통과 및 노치 필터를 사용합니다. 또 다른 변형인 퓨리에 변환 분광법 기구는 단색기를 미첼슨 간섭계로 대체하고 연속파 레이저를 사용합니다. 필터를 통과한 후, 복사선은 분석을 위해 냉각된 게르마늄 검출기에 집중됩니다.

기존의 라만 분광 광도계에는 레이저 소스, 샘플 홀딩 시스템, 파장 선택기 및 검출기가 포함됩니다.
단색 레이저 ...

raman-spectroscopy-instrumentation-overview

Education

교육

JoVE Core

Analytical Chemistry

분석 화학

Unit 1

제1단원

Molecular Vibrational Spectroscopy

분자 진동 분광학

KEY TERMS AND CONCEPTS

주요 용어 및 개념

raman spectroscopy setup and detectors

Raman spectroscopy uses a laser, a sample holder, a wavelength selector, and a detector to measure scattered light from a sample. The laser is monochromatic, meaning it has one main wavelength. It usually uses visible or near-infrared light to create a tightly focused beam.

That beam hits the sample and some of the light scatters. Liquid and gas samples are often placed in ordinary glass capillaries. Solid samples can be tested as powders packed into capillaries or as potassium bromide pellets.

The scattered light is collected by a separate lens and sent into a monochromator, which separates the light into its different frequencies. The output is then filtered carefully to remove stray laser light and Rayleigh scattering, which can hide the Raman signal. In fiber-optic Raman instruments, high-quality bandpass and notch filters are often used to reduce Rayleigh-scattered light.

Next, the optical signal is changed into an electrical signal by the detector. A charge-coupled device, or CCD, or a photomultiplier tube may be used. The signal can then be processed and displayed as a Raman spectrum.

Some Raman instruments use a different design called Fourier Transform Raman. In this setup, the monochromator is replaced by a Michelson interferometer, and a continuous-wave laser is used. After filtering, the radiation is focused onto a cooled germanium detector for analysis.

Raman Spectroscopy Setup and Detectors

infrared (ir) spectroscopy: overview

IR Spectra and Functional Group ID

Infrared (IR) spectroscopy helps identify functional groups in molecules by measuring how they absorb infrared light. It is based on the idea that electromagnetic radiation can move atoms or molecules from a lower energy state to a higher one when the radiation matches the energy gap between those states. In IR spectroscopy, that absorption happens as molecular vibrations change.

ir spectroscopy: molecular vibration overview

ir-spectroscopy-molecular-vibration-overview

IR Spectroscopy: Vibration Types and Bands

IR spectroscopy explains how covalently bonded molecules absorb infrared radiation by moving to higher vibrational levels. The key motions are stretching and bending vibrations. These motions help describe how a bond responds when it absorbs IR energy. Stretching vibrations happen along the bond line and change the distance between two bonded atoms. They can be symmetric, where two bonds lengthen and shorten together, or asymmetric, where one bond moves one way while another moves the opposite...

ir spectroscopy: hooke's law approximation of molecular vibration

ir-spectroscopy-hooke-s-law-approximation-of-molecular-vibration

Molecular Bond Vibrations in IR Spectroscopy

Molecular bond vibrations can be modeled with IR spectroscopy using Hooke’s law. A covalently bonded heteronuclear diatomic molecule is treated like two masses connected by a spring. The atoms act like the masses, and the bond acts like the spring. Hooke’s law links the vibrational frequency to two main factors. The frequency increases with the force constant, K, which describes bond stiffness. It decreases with the reduced mass, μ, which combines the masses of both atoms into one value for...

ir spectrometers

IR Spectrometer Signal Paths

IR spectrometers use infrared light to compare a sample beam with a reference beam and record how each one behaves. The two main instruments are dispersive IR spectrometers and Fourier transform infrared, or FTIR, spectrometers. In a dispersive IR spectrometer, a hot wire produces the infrared beam. Mirrors split it into two equal beams. One beam passes through the sample, and the other serves as the reference. The beams then move into the monochromator, which separates the radiation into a...

ir spectrum

IR Spectrum Peak Regions and Patterns

Infrared (IR) spectroscopy shows how a molecule responds when IR radiation passes through it. The bonds in the molecule stretch or bend as they absorb that energy. This creates an absorption spectrum, which plots percent transmittance against wavenumber. Transmittance is the ratio of radiant power that passes through a sample to the radiant power from the source. When transmittance is multiplied by 100, it becomes percent transmittance, or %T. %T ranges from 100% for no absorption to 0% for...

ir absorption frequency: hybridization

C-H Stretching in Alkane, Alkene, and Alkyne IR

Hydrocarbons such as alkanes, alkenes, and alkynes show characteristic C–H stretching bands in infrared, or IR, spectra. These bands help identify how the carbon atoms are hybridized. The bond type affects the stretching frequency that appears in the spectrum. The difference comes from s character, which is the amount of s-orbital contribution in a hybrid orbital. Among sp, sp2, and sp3 hybridized orbitals, sp has the most s character at 50%. Because of that, the electrons are held closer to...

ir absorption frequency: delocalization

Conjugation Shifts IR Bond Stretching

Conjugation shifts IR bond stretching because electron delocalization changes bond strength. Electron delocalization means electrons spread across more than one atom instead of staying in one bond or one atom. It is common in conjugated systems, where alternating single and double bonds let pi-electrons move through the molecule. This electron movement helps stabilize the molecule. It also lowers the double bond character of the bonds in the conjugated network. When a bond has less double bond...

ir frequency region: x&ndash;h stretching

IR Peaks for C-H, O-H, and N-H Bonds

IR spectroscopy shows the stretching bands of C-H, O-H, and N-H bonds in the 2700-4000 cm-1 range. These X-H bonds are useful for identifying common functional groups in a spectrum. Their peaks appear in different parts of this region and often have different shapes and strengths. C-H stretching gives sharp bands in the 2850-3000 cm-1 range. O-H stretching appears in the 3650-3200 cm-1 range, and N-H stretching appears in the 3500-3100 cm-1 range. N-H stretching usually shows one or two sharp...

ir frequency region: alkyne and nitrile stretching

ir-frequency-region-alkyne-and-nitrile-stretching

Triple-Bond Signals in IR Spectra

Alkyne and nitrile groups both contain triple bonds, and they show clear stretching bands in the diagnostic IR region. These absorptions usually appear around 2100 to 2300 cm −1 . This makes them useful markers when reading an IR spectrum. Triple bonds absorb at a higher stretching frequency than double bonds and single bonds. The C≡C bond stretches at a higher frequency than a C=C or C–C bond. The C≡N bond also stretches at a higher absorption than C=N and C–N bonds. This higher stretching...

ir frequency region: alkene and carbonyl stretching

ir-frequency-region-alkene-and-carbonyl-stretching

IR Signals for C=C and C=O Bonds

IR spectroscopy helps identify alkene double bonds and carbonyl groups by their stretching signals. These bonds absorb in a diagnostic region of the IR spectrum. Alkenes also show vinylic C–H stretching and C–H out-of-plane bending bands. Those bands can help determine substitution patterns on the double bond. The exact stretching frequency can change with bond environment. Resonance, inductive effects, ring strain, dipole moment, and hydrogen bonding can all shift the absorption. That is why...

ir frequency region: fingerprint region

IR Spectra: Diagnostic vs Fingerprint Region

IR spectra are divided into a diagnostic region and a fingerprint region. The diagnostic region lies above 1500 cm −1 and appears on the left side of the spectrum. It shows key bond stretches that help identify functional groups. In this region, single-bond vibrations from N-H, C-H, and O-H stretches appear at higher wavenumbers. The C≡C and C≡N stretches occur between 2100 and 2300 cm −1. The C=O, C=N, and C=C stretches appear between 1600 and 1850 cm −1. The fingerprint region lies below...

ir spectrum peak intensity: amount of ir-active bonds

ir-spectrum-peak-intensity-amount-of-ir-active-bonds

IR Peak Intensity and Bond Dipole Change

IR peak intensity depends on how much a bond’s dipole moment changes during vibration. When infrared light passes through a molecule, absorption happens only when a stretching or bending motion causes a substantial change in that bond dipole moment. That is what makes a molecule infrared active. Vibrational transitions usually fall in the infrared region from 4000 to 400 cm-1. Molecular bonds can stretch and bend in different ways, so an IR spectrum shows peaks with different intensities. The...

ir spectrum peak intensity: dipole moment

IR Absorption and Bond Dipole Changes

IR absorption depends on whether a bond has a changing dipole moment. A dipole moment comes from partial charge on each atom and the distance between them. It helps determine how strongly a bond absorbs infrared light and how intense the peak looks. A bond in an electric field can be stretched or compressed depending on the field direction. Infrared radiation has an electric field that flips direction very quickly. So polar bonds are pulled back and forth as the field reverses. If this motion...

ir spectrum peak broadening: hydrogen bonding

ir-spectrum-peak-broadening-hydrogen-bonding

Hydrogen Bonding Effects in IR O-H Peaks

Hydrogen bonding changes the O-H stretching peak in IR spectroscopy. The bond’s vibrational frequency depends on bond strength. Stronger bonds vibrate at higher frequencies, while weaker bonds vibrate at lower frequencies. In very dilute alcohol or phenol samples, or in the gas phase, the strong O-H bond gives a sharp peak at 3600-3650 cm−1. When intermolecular hydrogen bonding or intramolecular hydrogen bonding weakens the O-H bond, the stretch shifts to about 3300-3400 cm−1. This range of...

ir spectrum peak splitting: symmetric vs asymmetric vibrations

ir-spectrum-peak-splitting-symmetric-vs-asymmetric-vibrations

IR Peak Splitting in Amines and Nitro Groups

IR peak splitting can reveal how identical bonds in a polyatomic group are moving. These bonds may stretch in phase, which is symmetric stretching, or out of phase, which is asymmetric stretching. The two motions often create different IR peak shapes and positions. As a general rule, asymmetric stretching appears at a higher frequency than symmetric stretching. This pattern is useful for spotting functional groups in an IR spectrum. It also helps explain why some groups show one peak while...

applications of ir spectroscopy: overview

IR Spectroscopy Uses in Science and Forensics

IR spectroscopy is a useful tool for finding out what materials are made of. It is non-destructive, so the sample can often be kept intact. It gives chemical information about functional groups and the bonds between atoms in a molecule. This makes IR spectroscopy helpful in organic synthesis, pharmaceutical research, and materials science. Scientists use it to identify and characterize organic and inorganic compounds. It also helps with structural elucidation, which means working out a...

attenuated total reflectance (atr) infrared spectroscopy: overview

attenuated-total-reflectance-atr-infrared-spectroscopy-overview

ATR Infrared Spectroscopy for Material ID

ATR infrared spectroscopy is a method for identifying the composition of materials. It is used in chemistry, materials science, forensic science, and other areas where sample characterization is needed. The technique is useful because it usually needs little to no sample preparation and can be applied to many kinds of samples. The process starts when infrared, or IR, radiation is directed onto a diamond or germanium crystal. Because this crystal has a high refractive index, the IR beam...

raman spectroscopy: overview

Raman Spectra and Molecular Fingerprints

Raman spectroscopy uses laser light to study how molecules scatter light and reveal their vibrational energy levels. A monochromatic beam, or single-color light, hits the sample first. Most of the scattered light keeps the same frequency as the incoming light. This is called Rayleigh scattering. A small part of the light shifts in frequency because the photons exchange energy with molecular vibrations. That shifted light is Raman scattering. To collect a Raman spectrum, the sample is...

raman spectroscopy instrumentation: overview

Raman spectroscopy uses a laser, a sample holder, a wavelength selector, and a detector to measure scattered light from a sample. The laser is monochromatic, meaning it has one main wavelength. It usually uses visible or near-infrared light to create a tightly focused beam. That beam hits the sample and some of the light scatters. Liquid and gas samples are often placed in ordinary glass capillaries. Solid samples can be tested as powders packed into capillaries or as potassium bromide pellets.

key terms and concepts

Explore the main parts of a Raman spectrophotometer, from the laser and sample holder to filters, detectors, and Fourier Transform Raman design.

Raman Spectroscopy Setup and Detectors | JoVE K12

analytical chemistry

JoVE Core Analytical Chemistry simplifies complex chemical principles by breaking them down into clear, engaging animations, making topics from SI Units to NMR spectroscopy more accessible and straightforward. Additionally, the scientist-in-action videos highlight the application of these concepts in real-world research conducted in laboratories globally.

Raman Spectroscopy Setup and Detectors

Description

Transcript