Name: mosfet structure and operating regions
Uploaded: 2024-07-08T13:20:42.000Z
Duration: 1 min 17 s
Channel: JoVE

MOSFET의 필수 매개변수에는 채널 길이, 채널 폭, 산화물 두께, 접합 깊이 및 기판 도핑이 포함됩니다.
게이트 전압이 0인 경우 소스-드레인 전극은 두 개의 백투백 pn 접합을 형성하여 소스에서 드레인으로의 역 누설 전류만 허용합니다. 이를 차단 영역이라고 합니다.
게이트에서 양의 바이어스는 MOS 구조를 변환하여 두 개의 n-플러스 영역 사이에 표면 반전 레이어 또는 n-채널을 형성합니다.
작은 드레인 전압으로 전자는 전도 채널을 통해 소스에서 드레인으로 흐르며 저항기 역할을 하며 게이트 전압을 통해 컨덕턴스를 조정할 수 있습니다. 이것은 드레인 전류가 드레인-소스 전압에 비례하는 선형 영역입니다.
각 MOSFET에는 소스와 드레인 사이에 전도 경로를 생성하는 데 필요한 최소 게이트-소스 전압인 임계값 전압이 있습니다.
드레인 전압이 증가하면 포화되어 채널 길이의 가장자리 근처에 있는 반전층 두께가 0으로 감소합니다. 이 핀치 오프 지점은 포화 영역의 시작을 표시하며, 드레인 전압이 증가하더라도 드레인 전류가 일정하게 유지됩니다.

mosfet의 특성

금속 산화물 반도체 전계 효과 트랜지스터(MOSFET)는 전자 회로에서 중요한 역할을 합니다. 주로 신호 ​​증폭 및 전환에 사용됩니다.

다양한 필수 매개변수가 기능에 영향을 미치며 이는 이론 및 전자 응용 분야에 매우 중요합니다. 첫째, 채널 치수, 즉 길이와 너비가 매우 중요합니다. 이러한 채널의 크기는 트랜지스터의 전류 전달 능력과 스위칭 속도에 영향을 미칩니다. 채널이 짧을수록 일반적으로 더 빠른 작동이 가능합니다. 다음으로, 채널에서 게이트를 분리하는 이산화규소 층인 산화물 두께가 채널에 대한 게이트의 제어를 변조합니다. 더 얇은 산화물은 게이트 전기용량을 증가시켜 이러한 제어를 향상시킵니다.

또 다른 중요한 요소는 MOSFET의 임계 전압과 제어 누설 전류를 조정하는 접합 깊이와 기판 도핑입니다. 도핑은 불순물을 도입하여 반도체의 특성을 수정합니다.

작동상 MOSFET은 게이트-소스 전압을 기준으로 3개의 서로 다른 영역을 나타냅니다.

<ul style="list-style-type: disc; padding-left: 35px; margin: 0;">
	<li>차단 영역에서는 트랜지스터가 꺼지고 소스와 드레인 사이에 전도 경로가 표시되지 않아 전류가 최소한의 역방향 누설로 제한됩니다.</li>
	<li>V_GS가 임계값을 초과하고 V_DS(드레인-소스 전압)가 낮으면 선형 영역이 나타납니다. 여기서 트랜지스터는 드레인 전류(I_D)가 V_GS에 의해 변조된 V_DS에 정비례하는 가변 저항기처럼 작동합니다.</li>
	<li>포화 영역에서는 핀치오프 효과로 인해 V_DS가 증가함에도 불구하고 I_D 정체 상태가 발생합니다. 핀치오프 효과는 드레인 근처의 채널이 좁아져 추가 전류 흐름을 제한합니다.</li>
</ul>

이러한 작동 조건은 특히 정밀한 전자 제어가 필요한 회로에서 MOSFET이 구현되는 방식을 결정합니다.

MOSFET의 특성

MOSFET의 필수 매개변수에는 채널 길이, 채널 폭, 산화물 두께, 접합 깊이 및 기판 도핑이 포함됩니다.
와...

Education

교육

JoVE Core

Electrical Engineering

전기공학

Unit 1

제1단원

Transistors

트랜지스터

KEY TERMS AND CONCEPTS

주요 용어 및 개념

Characteristics of MOSFET

mosfet structure and operating regions

MOSFETs, or metal-oxide-semiconductor field-effect transistors, are important parts of electronic circuits. They are used to amplify and switch signals. Their behavior depends on several design features, including channel size, oxide thickness, junction depth, and substrate doping.

Channel length and channel width shape how much current a MOSFET can carry and how fast it can switch. Shorter channels usually allow faster operation. The oxide thickness also matters. This silicon dioxide layer sits between the gate and the channel, and thinner oxides increase gate capacitance, which strengthens gate control over the channel.

Junction depth and substrate doping also affect performance. These factors help set the threshold voltage, which is the gate-to-source voltage needed before the transistor turns on. They also help control leakage currents. Doping means adding impurities to change the properties of the semiconductor.

MOSFETs operate in three main regions based on gate-to-source voltage. In the cutoff region, the transistor is off and there is no conductive path between source and drain, aside from minimal reverse leakage. In the linear region, VGS is above threshold and VDS is low. The MOSFET then acts like a variable resistor, and drain current changes in proportion to VDS and is controlled by VGS.

In the saturation region, drain current stays nearly flat even when VDS increases. This happens because of pinch-off, where the channel near the drain narrows and limits further current flow. These operating regions help explain how MOSFETs are used when precise control is needed in circuits.

MOSFET Structure and Operating Regions

bipolar junction transistor

BJT Structure and Carrier Flow

Bipolar junction transistors are important parts of electronic circuits. They help make amplifiers, memories, and microprocessors work. A BJT can be built as either NPN or PNP, depending on its doping pattern, which means the type of impurities added to the material. A BJT has three layers: the emitter, base, and collector. It also has two p-n junctions, so the device has a sandwich-like structure. The emitter is heavily doped so it can inject charge carriers into the base. The base is very...

configurations of bjt

BJT Amplifier Modes and Uses

Bipolar Junction Transistor (BJT) configurations are defined by which terminal is shared by the input and output circuits. The shared terminal can be the base, emitter, or collector. Each setup has different electrical behavior and fits different circuit needs. In the common base configuration, the base is the common terminal. This setup has high voltage gain, so it can work well in single-stage amplifier circuits such as microphone pre-amplifiers. It also reduces the input current signal...

working principle of bjt

PNP BJT Current Flow in Active Mode

PNP bipolar junction transistors control current flow by moving charge carriers between the emitter, base, and collector. In a common-base setup, the transistor can amplify or switch electronic signals when it operates in active mode. In a PNP transistor, the emitter is heavily doped with holes, which are positive charge carriers. The base is lightly doped with electrons, which are negative carriers. A forward bias across the emitter-base junction lowers the potential barrier and lets holes...

characteristics of bjt

BJT Current-Voltage Curves in Common Emitter

The Bipolar Junction Transistor (BJT) in a common-emitter setup is studied by measuring its current-voltage curves. These measurements show how the transistor responds when voltage and current are changed in a controlled way. They are key to understanding how a BJT works in electronic circuits. The input characteristics are found by varying the base-emitter voltage while keeping the collector-emitter voltage constant. This test shows a Shockley-type relationship between the collector current...

modes of operations of bjt

BJT Biasing: Active to Inverted Mode

A bipolar junction transistor (BJT) works in four modes that depend on how its two junctions are biased. Those modes are active, saturation, cut-off, and inverted. The biasing pattern controls whether the transistor amplifies current or acts like a switch. Active mode is the most common mode for amplification. In this mode, the emitter-base junction is forward-biased and the base-collector junction is reverse-biased. Electrons move from the emitter into the base, while the collector blocks...

frequency response of bjt

BJT Amplifier Response at Low and High Freq

A BJT amplifier’s response changes with frequency in a common-emitter circuit. Its behavior at low frequencies and high frequencies depends on the circuit’s equivalent model. These models help explain how the transistor handles AC signals. At low frequencies, the DC bias point sets the transistor’s operation. The emitter-base voltage, base current, and collector current define this bias point. The load line also shapes how the amplifier works, using the applied voltage and load resistance. <br...

cut-off frequency of bjt

BJT Frequency Limits and Gain Drop

BJT frequency limits show when a bipolar junction transistor stops keeping a steady gain. These limits matter because they mark the shift from the pass band to the stop band in an electronic signal. They help explain why a transistor may amplify one range of frequencies well and weaken signals at higher frequencies. The alpha cut-off frequency applies to the common-base configuration. At low frequencies, the current gain alpha stays stable. Beyond this upper-frequency limit, alpha drops and...

switching of bjt

BJT as a Digital On-Off Switch

Bipolar junction transistors (BJTs) can work as digital on-off switches in electronic circuits. In this mode, the transistor moves between cut-off and saturation. These two states match the off and on positions of an ideal switch. In cut-off mode, both the emitter-base junction and the collector-base junction are reverse-biased. This blocks current flow through the transistor and keeps it off. Circuits use this state when no signal transmission is needed, which helps maintain a low-power...

bjt amplifiers

Common-Emitter BJT Voltage Gain

Bipolar junction transistors, or BJTs, can act as amplifier parts when they work in the active region. In this mode, a small change in base-emitter voltage controls a larger collector current. That makes the transistor act like a voltage-controlled current source and lets it boost a weak signal into a stronger one. A common-emitter BJT amplifier uses that current change to create voltage gain. The output current flows through a load resistor, and the voltage drop across that resistor sets the...

small-signal analysis of bjt amplifiers

BJT Amplifier Gain and Input Resistance

BJT amplifier gain and input resistance can be analyzed with a small-signal model. In the active region, a bipolar junction transistor is used for linear amplification. Its base-emitter voltage includes a DC bias and a small AC signal. That input produces a collector current with both DC and AC parts. When the AC input signal is much smaller than the thermal voltage VT, the small-signal approximation applies. This makes it possible to find the AC collector current from the DC collector current...

field effect transistor

Field Effect Transistor Types and Uses

Field-effect transistors, or FETs, are important parts of electronic circuits. They have three terminals: gate, drain, and source. FETs are unipolar devices, which means they use either electrons or holes as charge carriers. That is different from bipolar transistors, which use both types of carriers. A FET controls the flow of charge from the source to the drain through a channel. The voltage difference between the gate and source controls how well that channel conducts. This makes the device...

characteristics of jfet

JFET Output Regions and Current Control

JFET output characteristics show how drain current changes with drain-source voltage and gate-source voltage. In a junction field effect transistor, the gate-source voltage controls the drain current. When the drain and gate voltages are set to zero, the device is in equilibrium and no net current flows. With the gate voltage held at zero, the drain current rises linearly as the source-drain voltage increases. This linear part is called the Ohmic region. In this region, the JFET acts like a...

biasing of fet

JFET Gate-Source Bias and Current Control

JFET gate-source bias controls current flow in a junction field effect transistor. A JFET uses one carrier type and comes in N-channel or P-channel forms. In both cases, the channel is surrounded by PN junctions, and those junctions help control how current moves through the device. In an N-channel JFET, N-type material forms the channel on a P-type substrate. The gate is made of P-type material. Biasing this device means applying a negative voltage to the gate relative to the source. That...

mos capacitor

MOS Capacitor Voltage and Charge

A MOS capacitor uses voltage to control charge in a semiconductor. It is a key structure in semiconductor device technology and in the fabrication of integrated circuits and MOSFETs, or metal-oxide-semiconductor field-effect transistors. The structure has three layers. A metal gate sits on top and is usually made from a highly conductive material such as aluminum or polysilicon. Below it is a thin insulating oxide layer, usually silicon dioxide (SiO2), and below that is a semiconductor...

mosfet

MOSFET Current Control in Electronics

The MOSFET is a semiconductor device that controls electrical current in modern electronics. It is also called an IGFET or MISFET. The three main terminals are the source, drain, and gate. MOSFETs are classified as n-channel or p-channel devices. The type depends on the doping of the substrate and the source or drain regions. In an n-MOSFET, the source and drain are n-type regions separated from a p-type substrate by reverse-biased p-n diodes. The gate is built from a metal plate over an...

characteristics of mosfet

MOSFETs, or metal-oxide-semiconductor field-effect transistors, are important parts of electronic circuits. They are used to amplify and switch signals. Their behavior depends on several design features, including channel size, oxide thickness, junction depth, and substrate doping. Channel length and channel width shape how much current a MOSFET can carry and how fast it can switch. Shorter channels usually allow faster operation. The oxide thickness also matters. This silicon dioxide layer...

mosfet: enhancement mode

MOSFET Switching in Enhancement Mode

Enhancement-mode MOSFETs are MOSFETs that work as controlled electronic switches. They belong to the metal-oxide semiconductor field-effect transistor family. These devices come in two forms: n-channel and p-channel, and each one is used for a different polarity of operation. At zero gate-source voltage, or Vgs, an enhancement-mode MOSFET is usually non-conductive. In that default off state, no current flows between the drain and source terminals. When a positive Vgs is applied, it creates an...

mosfet: depletion mode

Depletion MOSFET Channel Control

Depletion-mode MOSFETs are normally on transistors with a built-in channel that conducts current without gate bias. They work differently from enhancement-mode MOSFETs, which need a positive gate-source voltage, or V gs, to turn on. In a depletion device, the channel is already open because the channel doping creates a low-resistance path between the drain and source. These devices behave much like junction field-effect transistors, or JFETs. The channel conductivity is set by the material...

mosfet amplifiers

MOSFET Gain and Biasing

MOSFET gain and biasing shape how a MOSFET amplifier works. When a MOSFET operates in its active region, it acts like a voltage-controlled current source. The gate-to-source voltage sets the drain current, and that behavior supports transconductance amplification. The output current then flows through a load resistor. That load resistor turns the circuit into a voltage amplifier. The output voltage is found by subtracting the voltage drop across the load resistor from the supply voltage, so...

small-signal analysis of mosfet amplifiers

small-signal-analysis-of-mosfet-amplifiers

MOSFET Amplifier Gain and Signal Distortion

MOSFET amplifiers can be treated as linear circuits when they operate in the saturation region. The gate-to-source voltage, or VGS, is the sum of a DC bias voltage and a small time-varying input signal. That bias sets the operating point and controls the drain current that flows from drain to source. When a small AC signal is added at the gate, the drain current has three parts. One part is the DC bias current, ID0, which is the quiescent current with no signal applied. A second part changes...

key terms and concepts

Learn how MOSFET channel size, oxide thickness, doping, and voltage levels affect current flow, switching speed, and the cutoff, linear, and saturation regions.

MOSFET Structure and Operating Regions | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

MOSFET Structure and Operating Regions

Description

Transcript