Name: shear strain in a circular shaft
Uploaded: 2024-05-23T12:59:40.000Z
Duration: 1 min 10 s
Channel: JoVE

원형 샤프트의 독특한 특성은 비틀림 하에서 모든 단면이 평면으로 유지되고 왜곡되지 않고 단단한 단단한 슬래브로 회전한다는 것입니다.
전단 응력의 분포를 결정하려면 길이가 L이고 반지름이 R인 원형 샤프트 내부의 원통형 단면을 한쪽 끝이 고정되어 있는 것을 고려하십시오. 원통형 단면의 반지름은 r입니다.
이제 하중이 가해지기 전에 원통형 단면의 표면에 인접한 두 개의 원과 직선으로 형성된 작은 사각형 요소를 고려하십시오.
비틀림 하중이 샤프트에 가해지면 사각형 요소가 마름모로 변형됩니다. 마름모의 양면이 고정되어 있기 때문에 전단 변형률은 선 AB와 A'B 사이의 각도와 같습니다.
작은 각도 근사치와 적절한 형상을 사용하여 비틀림에서 샤프트의 주어진 지점에서의 전단 변형률이 비틀림 각도와 샤프트 축으로부터의 거리 r에 비례한다는 것을 보여줄 수 있습니다. 샤프트 표면에서 최대입니다.

원형 샤프트의 변형

원형 샤프트의 독특한 특징 중 하나는 비틀림에도 단면 무결성을 유지하는 능력입니다. 즉, 각 단면은 평평하고 변경되지 않은 개체로 계속 존재하며 단순히 단단하고 견고한 슬래브처럼 회전합니다. 이러한 샤프트 내의 전단 응력 분포를 이해하려면 이 원형 샤프트 내부의 원통형 단면을 고려하십시오. 이 단면의 길이는 L이고 반경은 R이며 한쪽 끝은 고정되어 있습니다. 원통형 단면의 반경은 r로 표시됩니다.

하중을 가하기 전에 원통형 단면 표면의 작은 사각형 요소를 고려하십시오. 이 요소는 인접한 두 개의 원과 직선으로 구성됩니다. 이 사각형 요소는 샤프트에 비틀림 하중이 가해지면 마름모 모양으로 변형됩니다. 마름모의 두 변이 고정되어 있다고 가정할 때 전단 변형률은 원통 단면의 벽에 그려진 수직선 AB와 마름모의 변을 따라 그려진 경사선 A'B 사이의 각도와 같습니다. 작은 각도 근사와 적절한 형상을 적용함으로써 비틀림을 겪는 샤프트의 특정 지점에서의 전단 변형이 비틀림 각도와 샤프트 축으로부터의 거리 r에 정비례한다는 것을 입증할 수 있습니다. 이 변형은 샤프트 표면에서 최대에 도달합니다.

원형 샤프트의 독특한 특성은 비틀림 하에서 모든 단면이 평면으로 유지되고 왜곡되지 않고 단단한 단단한 슬래브로 회전한다는 것입니다.
받는 사람...

Education

교육

JoVE Core

Mechanical Engineering

기계공학

Unit 1

제1단원

Torsion

비틀림

KEY TERMS AND CONCEPTS

주요 용어 및 개념

Deformation in a Circular Shaft

shear strain in a circular shaft

Shear strain in a circular shaft describes how the shaft’s surface changes shape under torsion. A circular shaft keeps each cross-section flat and undistorted as it twists. Each section behaves like a rigid slab that rotates in place.

To study the strain inside the shaft, consider a cylindrical section with length L and radius R. One end of this section is fixed. The radius at a point inside the section is labeled r.

Before the load is applied, a small square element lies on the surface of the cylinder. It is formed by two neighboring circles and straight lines. When torsion is applied, that square element changes into a rhombus.

Because two sides of the rhombus stay anchored, the shearing strain can be measured by the angle between line AB on the cylinder wall and the inclined line A'B along one side of the rhombus. Using small-angle approximation and basic geometry, the shear strain at a point in the shaft is proportional to the angle of twist and to the distance r from the shaft’s axis. The strain is greatest at the outer surface.

Shear Strain in a Circular Shaft

stresses in a shaft

Torque and Shear in a Twisted Shaft

A shaft under torque develops internal shear forces as it twists. In this setup, equal and opposite torques act on the shaft PQ. To study the effect, a section is cut perpendicular to the shaft axis at an arbitrary point R. The free-body diagram of the QR segment shows the shearing forces applied by the PR portion. These forces act as the shaft resists twisting. Using equilibrium on the QR segment links the internal shear forces in the cut section to the internal torque. Here, r is the...

deformation in a circular shaft

Shear strain in a circular shaft describes how the shaft’s surface changes shape under torsion. A circular shaft keeps each cross-section flat and undistorted as it twists. Each section behaves like a rigid slab that rotates in place. To study the strain inside the shaft, consider a cylindrical section with length L and radius R. One end of this section is fixed. The radius at a point inside the section is labeled r. Before the load is applied, a small square element lies on the surface of...

circular shaft - stresses in linear range

Torsion Formula for Circular Shafts

Torsion in a circular shaft is analyzed when the applied torque stays within Hooke's law. In this linear range, the shaft does not undergo permanent deformation. The discussion uses shearing strain, shearing stress, and the modulus of rigidity to build the stress equation. The derivation also requires the moments of the small forces on a cross-section to equal the applied torque. When the shearing stress expression is rewritten, an integral term appears. This term represents the polar moment...

angle of twist - elastic range

Elastic Twist in a Circular Shaft

Elastic twist in a circular shaft describes how a cylindrical shaft rotates when torque is applied. The shaft has a length L and a uniform radius r. A torque at the free end creates shearing strain, which is greatest at points farther from the shaft axis. When the shaft stays within the elastic range, the shearing strain can be written in terms of the applied torque, radial distance, polar moment of inertia, and modulus of rigidity. The polar moment of inertia is a geometric measure of how the...

angle of twist: problem solving

Shaft Torsion Between Pulleys B and C

Shaft torsion between pulleys B and C is found by analyzing how torque twists an aluminum shaft. An electric motor applies 700 N·m of torque and produces stable rotation. The shaft carries pulleys B and C, which experience torques of 300 N·m and 400 N·m. The calculation starts with a section cut between pulleys B and C. A free-body diagram is used to study the cut cross-section. Because pulley B has an anticlockwise torque, the torque at the cut must balance it in the opposite direction. The...

design of transmission shafts

Sizing a Transmission Shaft by Torque

A transmission shaft is sized from the power it must carry and the speed it rotates at. These two design limits guide the choice of shaft material and cross-sectional size. The goal is to keep the maximum shearing stress within the elastic limit while still transmitting the needed power. Power is directly linked to torque, which is the twisting force applied to the shaft. By rearranging the power relation, the torque can be found from the required power and the shaft speed. That torque value...

stress concentrations in circular shafts

Why Shafts Develop Local Stress Peaks

Circular shafts can develop local stress peaks when torque is applied through real machine parts. The elastic torsion formula works best for a circular shaft with a uniform cross-section and rigid plates fixed to its ends. In practice, torque is often passed through flange couplings or gears, and these parts use keys in keyways to connect to the shaft. That loading method changes the stress pattern near the point where torque enters the shaft. The stress distribution no longer matches the...

plastic deformation in circular shafts

Torsional Failure and Plastic Strain in Shafts

Plastic deformation in circular shafts happens when torsional force pushes the material past its yield strength. At that point, the shaft does not return to its original shape. Instead, it keeps a permanent strain. To measure this change, the stress pattern inside the shaft must be understood. The maximum shearing stress is calculated first. Then a shearing-stress-strain diagram can be drawn to find the maximum shearing strain. Shearing strain changes linearly with the distance from the shaft...

circular shafts - elastoplastic materials

Torsion Limits in Circular Shafts

Circular shafts under torsion show a clear change from elastic behavior to plastic deformation as torque increases. In the elastic limit, stress rises in direct proportion to the distance from the shaft’s center. The outer material carries the highest stress first, and the shaft can still return to its original shape. At a critical stress level, the shaft begins to yield. This marks the maximum torque the shaft can carry without permanent deformation. Beyond this point, a plastic region forms...

residual stresses in circular shafts

Residual Stress After Shaft Torsion

Residual stress can remain in a circular shaft after torque causes plastic deformation. This happens in elastoplastic materials, which show both elastic and plastic behavior. The plastic change can come from high shearing stress or large strain. Residual stress is the internal stress that stays in the material after the external force is removed. In a shaft under torque, the angle of twist does not return fully to its original value. That lasting change shows that residual stress is still...

torsion of noncircular members

Torsion in Square and Rectangular Bars

Torsion in square and rectangular bars shows how shape changes the way a material twists. Circular shafts keep their cross-sections nearly unchanged because they are axis-symmetric. That symmetry helps the stress spread evenly, so the shaft can resist torsion without distorting. Square bars behave differently because they do not have the same axial symmetry. When twisted, their cross-sections distort, although the diagonals and the lines connecting the midpoints stay as exceptions. This means...

thin-walled hollow shafts

Shear Flow in Thin-Walled Shafts

Shear flow in a thin-walled hollow shaft describes how torsional force is carried through the wall. When a small segment of width dx is isolated, it is still in equilibrium, but it experiences torsional shearing forces at its ends. These forces come from the longitudinal shearing stress on the segment's minor surface multiplied by that surface area. The result is a uniform shear flow through the structure. To study the wall more closely, a small section with length ds is considered. The force...

key terms and concepts

Learn how torsion changes a circular shaft’s shape, why cross-sections stay flat, and why shear strain increases with distance from the axis.

Shear Strain in a Circular Shaft | JoVE K12

JoVE Core Mechanical Engineering offers concise, easy-to-understand animated videos covering key topics such as equilibrium, forces, truss analysis, and structural mechanics. Explore their real-world applications, and witness these concepts in action through scientist-led experiments.

mechanical engineering

Shear Strain in a Circular Shaft

Description

Transcript