Name: concrete voids and strength
Uploaded: 2024-11-07T14:48:30.000Z
Duration: 1 min 12 s
Channel: JoVE

공극의 총 부피에는 겔 물, 모세관 기공 및 갇힌 공기가 차지하는 부피가 포함되며, 각각이 콘크리트 구조물의 전체 다공성에 기여하는 콘크리트 덩어리를 생각해 보십시오.
시멘트 수화의 산물인 겔은 수화물의 광범위한 표면적에 물리적으로 유지되거나 흡착된 고체 물질과 물로 구성됩니다. 이 특정 물의 부피는 젤 워터의 부피입니다.
1입방인치의 수화되지 않은 시멘트는 완전한 수화 시 수화 제품을 위해 약 2입방인치의 공간이 필요한 것으로 추정됩니다.
모세관 기공은 수화 제품이 차지하지 않는 수화 시멘트 페이스트 내의 공간이며, 이러한 기공은 비어 있거나 물로 채워질 수 있습니다.
콘크리트를 혼합하는 과정에서 일부 공기가 시멘트 페이스트 내에 갇히는 경우가 많습니다.
이러한 갇힌 공기 공극은 최대 120mil에 달할 수 있으며, 이는 모세관 공극보다 훨씬 크며 콘크리트의 강도에 부정적인 영향을 미칠 수 있습니다.

콘크리트의 전공극량

Total Voids in Concrete

콘크리트의 전공극량은 겔수 부피, 모세관 기공 및 갇힌 공기를 포함합니다. 겔수(시멘트 수화 생성물 내에 유지됨)와 물리적으로 갇히거나 흡착된 물은 수화 과정에 중요합니다. 완전한 수화를 위해서는 1세제곱 센티미터의 시멘트 생성물에 필요한 공간이 두 배라고 추정됩니다. 모세관 기공은 수화된 시멘트 페이스트 내의 비어 있는 공간을 구성하며, 그 크기는 물-시멘트 비율과 수화도에 크게 영향을 받습니다.


 혼합하는 동안 콘크리트는 소량의 공기를 가두어 모세관 기공보다 상당히 큰 공극을 형성하여 잠재적으로 콘크리트의 강도를 약화시킵니다. 이러한 공기 공극은 크기가 다양합니다. 갇힌 공극은 최대 3밀리미터에 이르며, 나노미터에서 수 마이크로미터 직경의 미세한 모세관 기공보다 훨씬 큽니다. 이러한 모세관 기공의 분포는 총 다공성보다 수화된 시멘트 페이스트 특성을 평가하는 데 더 정확한 지표로 여겨집니다.


 일반적으로 구 모양을 한 공기 공극은 불규칙한 모양의 모세관 기공과 대조됩니다. 이러한 공극이 콘크리트에 미치는 영향은 상당하여 강도와 투과성에 영향을 미칩니다. 콘크리트의 특성을 최적화하려면 이러한 공극의 부피와 분포를 이해하고 제어하는 ​​것이 필수적입니다.

공극의 총 부피에 겔 물, 모세관 기공 및 갇힌 공기가 차지하는 부피가 포함되는 콘크리트 덩어리를 고려하십시오.

Education

교육

JoVE Core

Civil Engineering

토목공학

Unit 1

제1단원

Strength of Concrete

콘크리트 강도

KEY TERMS AND CONCEPTS

핵심 용어 및 개념

concrete voids and strength

Concrete voids affect both strength and permeability. They include gel water, capillary pores, and entrapped air. In hydrated cement paste, gel water is held within the cement hydration products. Physically entrapped or adsorbed water also supports the hydration process.

As cement hydrates, the space needed for the products from a cubic centimeter of cement is estimated to double. Capillary pores are the open spaces left inside the hydrated paste. Their size depends mainly on the water-to-cement ratio and the degree of hydration. The pattern of these pores can give a better picture of hydrated cement paste than total porosity alone.

Concrete also traps a small amount of air during mixing. These air voids can be much larger than capillary pores and may weaken concrete strength. Entrapped air voids can reach up to 3 millimeters in size. By comparison, capillary voids range from nanometers to a few micrometers.

Air voids are usually spherical. Capillary voids are more irregular in shape. Because void volume and void distribution affect concrete so strongly, understanding and controlling them helps improve concrete properties.

Concrete Voids and Strength

tensile strength considerations of concrete

tensile-strength-considerations-of-concrete

How Cracks Limit Concrete Strength

Concrete tensile strength is limited by tiny cracks inside the material. The cement paste itself can be much stronger in theory than it is in practice. In real concrete, the measured strength can be up to a thousand times lower than the theoretical value. These small cracks help explain that gap. When a load is applied, stress rises at the crack tips. This idea is described by Griffith's theory of brittle fracture. In brittle materials, cracks can grow quickly once the stress at their tips...

behavior of concrete under compressive load

behavior-of-concrete-under-compressive-load

Concrete Failure Patterns Under Compression

Concrete failure patterns under compression show how the material responds to different kinds of direct stress. These patterns help explain concrete’s structural integrity. Under uniaxial compression, where force acts in one direction, cracks often form parallel to the load. These parallel cracks come from local tensile stress, which is pulling stress that appears perpendicular to the compression direction. As uniaxial loading continues, angled cracks may also appear. These cracks are linked...

porosity in cement paste

How Cement Curing Changes Porosity

Cement curing changes porosity in the hardened paste. Porosity means the void spaces inside concrete. These spaces affect both strength and durability. When water and cement react, hydration forms a semi-solid paste that traps water in different ways. Some of that water becomes combined water. It makes up about 23% of the cement's dry mass. Other water stays as gel water, which fills very small voids called gel pores. Gel pores account for about 28% of the cement gel volume. The...

total voids in concrete

Concrete voids affect both strength and permeability. They include gel water, capillary pores, and entrapped air. In hydrated cement paste, gel water is held within the cement hydration products. Physically entrapped or adsorbed water also supports the hydration process. As cement hydrates, the space needed for the products from a cubic centimeter of cement is estimated to double. Capillary pores are the open spaces left inside the hydrated paste. Their size depends mainly on the...

pore size distribution

Concrete Porosity and Durability

Concrete porosity and durability depend strongly on pore size distribution in hardened cement paste. Capillary pores are much larger than gel pores, and in partially hydrated cement paste they form a connected network that lowers strength and raises permeability. Higher permeability makes concrete more vulnerable to freeze-thaw damage and chemical attack. The risk also depends on the water-to-cement ratio. A higher ratio can leave more space for capillary pores to remain open. As cement...

microcracking in concrete

How Concrete Cracks Before Failure

Concrete can develop tiny cracks before any outside load is applied. These microcracks usually form at the boundary between coarse aggregate and hydrated cement paste. They often result from small volume changes caused by stress-strain differences, heat, and moisture movement. At first, these microcracks stay stable. They usually do not grow much until the concrete reaches about 30 percent of its ultimate strength. As the load rises, the material can begin to change more quickly. When...

water cement ratio

Concrete Strength and Water Balance

Concrete strength depends on the balance between water and cement in the mix. This water-cement ratio is the weight of water compared with the weight of cement. It affects strength, durability, and how well concrete resists environmental stress. Abrams’ law shows that less water usually makes stronger concrete. Water is still needed for hydration, which is the chemical process that binds water and cement. It also helps the mix stay workable and compactable. Some water must be absorbed into the...

aggregate cement ratio

How Mix Ratio Changes Concrete Strength

The aggregate cement ratio changes how concrete performs. It is the weight of aggregate divided by the weight of cement in a concrete mix. This ratio affects strength, workability, and durability, so it is an important part of concrete design. A higher aggregate cement ratio makes the mix leaner. Lean mixes have less cement paste to coat and lubricate the aggregate, so they can be harder to work with. At the same time, they may increase strength because the concrete has less total porosity, or...

transition zone

Concrete Transition Zone and Its Porosity

The concrete transition zone is the thin region where aggregate meets cement paste. It has more pores than the surrounding material, so it is usually weaker at first. The bond around the aggregate comes mainly from Van der Waals forces, which are weak attraction forces between particles. When concrete is compacted, this zone often has a higher water-cement ratio near the aggregate. That extra water can form thin water films around the coarse aggregate. These films increase porosity and help...

relation between tensile strength and compressive strength of concrete

relation-between-tensile-strength-and-compressive-strength-of-concrete

Concrete Strength Testing: Tension vs. Compression

Concrete strength testing compares tensile strength and compressive strength. These two properties are related, but they do not rise at the same rate. Tensile strength usually grows more slowly than compressive strength, so the balance between them changes as concrete gets stronger. Several factors affect tensile strength measurements. The test method, specimen size and shape, aggregate texture, and moisture content can all change the result. Direct tension tests are difficult to perform...

fatigue strength of concrete

Concrete Fatigue Under Repeated Loads

Concrete fatigue describes how concrete can weaken or fail when loads are applied again and again, even when each load is below the material’s strength limit. This property matters because it affects the durability and service life of concrete structures. In materials science and engineering, fatigue is a key reason concrete may not last as long as expected under real use. Concrete can fail in two main ways through fatigue. Static fatigue, also called creep rupture, happens under a constant...

impact strength of concrete

Concrete Impact Resistance in Real Use

Concrete impact resistance matters when a material must handle repeated blows and sudden loads. It is important during pile driving, where concrete piles are driven into the ground. It also matters for machinery foundations that experience impulsive loads and for precast concrete parts that can be damaged during handling. Impact strength is measured by checking how well concrete absorbs energy from repeated impacts. A major sign of serious damage is when the concrete does not rebound after...

abrasion resistance of concrete

Concrete Wear Tests and Surface Durability

Concrete wear tests show how well a surface can stand up to abrasion and long-term use. Abrasion is the wearing away of a material by rubbing, scraping, or contact with moving solids. This property matters because concrete surfaces can lose material under vehicle traffic or when solids carried in water brush against them. The transcript describes three tests used to measure concrete abrasion resistance. In the revolving disc test, three plates rotate against the concrete, and silicon carbide...

reinforcements in concrete

Steel Bars in Concrete Structures

Steel bars in concrete structures help the material carry both compression and tension. Concrete is strong when it is squeezed, but it is weak when pulled. Rebar, or reinforcing steel bars, is placed inside the concrete to handle those tensile forces. Steel is a practical choice because it has a similar coefficient of thermal expansion to concrete. That means both materials expand and contract in a similar way as temperature changes. The steel used for reinforcement is usually made by a...

fiber reinforced concrete

Concrete Strength with Added Fibers

Fiber-reinforced concrete is concrete that includes added fibers to improve strength and durability. It uses hydraulic cement with fine or coarse aggregates, plus separated, non-continuous fibers mixed through the material. These fibers can come from steel, glass, and polymers, as well as natural sources such as sisal and cellulose or manufactured sources such as polypropylene and Kevlar. Steel fibers are often preferred because they are strong and tough. They help concrete resist cracking and...

prestressed concrete

How Concrete Is Preloaded for Strength

Prestressed concrete is a construction method that preloads concrete so it can handle more stress. High-strength steel strands are stretched before or after the concrete is loaded in service. The goal is to put the concrete into compression. That compression helps balance the tension the structure will face later. By reducing tension, prestressing helps limit cracks in the concrete. It can also let a structure carry greater loads or span longer distances than conventional reinforced concrete.

ferrocement

Ferrocement Mesh and Mortar Design

Ferrocement is a construction material made from dense layers of mesh or fine rods covered fully in cement mortar. It is a form of reinforced concrete, but it uses mesh instead of the larger steel bars found in standard reinforced concrete. This structure gives ferrocement its thin, flexible form. The material is built from wire meshes and a mortar made of cement and sand. The mortar is usually mixed in a 1:2 or 1:3 ratio. The water-to-cement ratio is kept between 0.40 and 0.45. This helps the...

non-destructive tests for concrete strength

non-destructive-tests-for-concrete-strength

Concrete Strength Checks Without Breaking It

Concrete strength can be checked without fully breaking the material. Two common methods are the rebound hammer test, also called the Schmidt hammer test, and the penetration resistance test, also called the Windsor Probe test. Both are used to estimate the strength of existing concrete. The rebound hammer test measures the hardness of the concrete surface and gives an indirect clue about strength. A spring-driven mass moves inside a tubular housing and strikes a plunger against the concrete.

key terms and concepts

Learn how gel water, capillary pores, and entrapped air create voids in concrete and how they affect strength, permeability, and cement hydration.

Concrete Voids and Strength | JoVE K12

JoVE Core Civil Engineering offers a foundational exploration of essential construction materials such as bricks, stones, steel, wood, and concrete, along with fluid mechanics topics like flow over immersed bodies, open channel flow, and dimensional modeling. It also covers key surveying concepts, including leveling, traverse adjustments, curve design, topographic mapping, and geospatial technologies (GPS & GIS). Science-in-action videos showcase laboratory research on materials, fluids, and surveying practices in real-world engineering systems.

civil engineering

Concrete Voids and Strength

Description

Transcript