Name: how concrete cracks before failure
Uploaded: 2024-11-07T14:48:30.000Z
Duration: 1 min 20 s
Channel: JoVE

미세 균열은 굵은 골재와 시멘트 페이스트 사이의 경계면에 하중이 가해지기 전에도 형성될 수 있습니다.
콘크리트의 최대 강도의 약 30%까지 이러한 균열은 안정적으로 유지되고 팽창하지 않습니다.
응력이 콘크리트의 최대 강도의 30%를 초과하면 골재와 시멘트 페이스트 사이의 계면에서 길이, 너비 및 빈도가 증가하는 미세 균열인 결합 균열의 형성이 관찰됩니다.
본드 균열은 콘크리트의 곡선 응력-변형률 곡선에 의해 반영되며, 이는 응력이 응력을 앞지르는 변형률의 증가를 나타냅니다.
콘크리트가 최대 강도의 70-90%에 도달하면 모르타르 매트릭스를 통해 균열이 형성되기 시작하여 기존 접착 균열을 연결하고 연속적인 패턴을 만듭니다.
당연히 재료에 가해지는 하중이 증가하면 재료가 공칭 극한 강도에 도달했을 때 즉각적인 고장으로 이어질 수 있습니다.
초음파 및 음향 방출 테스트는 콘크리트의 균열 진행 상황을 추적할 수 있습니다.
균열이 발생함에 따라 횡 초음파 펄스 속도가 눈에 띄게 감소하고 음향 방출이 증가하여 고장을 나타냅니다.

콘크리트의 미세균열

Microcracking in Concrete

콘크리트의 미세균열은 외부 하중이 가해지기 전에도 재료 내부에 형성될 수 있는 작은 균열을 말합니다. 이러한 미세균열은 일반적으로 굵은 골재와 수화된 시멘트 페이스트 사이의 계면에서 발생하며, 종종 응력-변형 거동의 변화와 열 및 수분 이동으로 인해 발생하는 체적 변화의 결과로 발생합니다. 이러한 미세균열은 처음에는 안정을 유지하며 콘크리트가 최대 강도의 약 30%까지 응력을 받을 때까지 크게 커지지 않습니다.


 콘크리트가 최대 하중 지지 용량의 70~90%에 접근함에 따라, 균열은 시멘트 페이스트와 잔골재로 구성된 모르타르 매트릭스를 통해 전파되어 결합 균열을 연결하고 연속적인 균열 패턴을 형성합니다. 균열의 빠른 전파라고 하는 이 현상은 하중이 지속되면 시간이 지남에 따라 파손으로 이어질 수 있으며, 이를 정적 피로라고 합니다.


 적용된 하중이 더 증가하면 피크 강도 수준에서 빠른 파손이 발생할 수 있습니다. 미세 균열의 형성 및 진화는 초음파 및 음향 방출 테스트와 같은 비파괴 검사 방법을 통해 관찰할 수도 있습니다. 콘크리트가 더 많은 응력을 받으면 균열 전파 속도가 가속화되어 구조적 파손으로 이어집니다. 미세 균열을 이해하는 것은 하중 하에서 콘크리트의 거동과 결국 수리 또는 보강이 필요한 상황을 예측하는 데 중요합니다.

미세 균열은 굵은 골재와 시멘트 페이스트 사이의 경계면에 하중이 가해지기 전에도 형성될 수 있습니다.
최대 약 30 %의 ...

Education

교육

JoVE Core

Civil Engineering

토목공학

Unit 1

제1단원

Strength of Concrete

콘크리트 강도

KEY TERMS AND CONCEPTS

핵심 용어 및 개념

how concrete cracks before failure

Concrete can develop tiny cracks before any outside load is applied. These microcracks usually form at the boundary between coarse aggregate and hydrated cement paste. They often result from small volume changes caused by stress-strain differences, heat, and moisture movement.

At first, these microcracks stay stable. They usually do not grow much until the concrete reaches about 30 percent of its ultimate strength. As the load rises, the material can begin to change more quickly.

When concrete approaches about 70 to 90 percent of its maximum load-bearing capacity, cracks can spread through the mortar matrix. The mortar matrix is the mix of cement paste and fine aggregate. These growing cracks connect bond cracks and create a continuous cracking pattern.

This stage is called fast propagation of cracks. If the load stays in place, the concrete may eventually fail over time. That slow breakdown is known as static fatigue. If the load increases further, rapid failure can happen at peak strength.

Engineers can track microcrack growth with non-destructive tests. Ultrasonic testing and acoustic emission testing can both reveal the formation and spread of cracks. Watching how crack growth speeds up helps predict when concrete may need repair or reinforcement.

How Concrete Cracks Before Failure

tensile strength considerations of concrete

tensile-strength-considerations-of-concrete

How Cracks Limit Concrete Strength

Concrete tensile strength is limited by tiny cracks inside the material. The cement paste itself can be much stronger in theory than it is in practice. In real concrete, the measured strength can be up to a thousand times lower than the theoretical value. These small cracks help explain that gap. When a load is applied, stress rises at the crack tips. This idea is described by Griffith's theory of brittle fracture. In brittle materials, cracks can grow quickly once the stress at their tips...

behavior of concrete under compressive load

behavior-of-concrete-under-compressive-load

Concrete Failure Patterns Under Compression

Concrete failure patterns under compression show how the material responds to different kinds of direct stress. These patterns help explain concrete’s structural integrity. Under uniaxial compression, where force acts in one direction, cracks often form parallel to the load. These parallel cracks come from local tensile stress, which is pulling stress that appears perpendicular to the compression direction. As uniaxial loading continues, angled cracks may also appear. These cracks are linked...

porosity in cement paste

How Cement Curing Changes Porosity

Cement curing changes porosity in the hardened paste. Porosity means the void spaces inside concrete. These spaces affect both strength and durability. When water and cement react, hydration forms a semi-solid paste that traps water in different ways. Some of that water becomes combined water. It makes up about 23% of the cement's dry mass. Other water stays as gel water, which fills very small voids called gel pores. Gel pores account for about 28% of the cement gel volume. The...

total voids in concrete

Concrete Voids and Strength

Concrete voids affect both strength and permeability. They include gel water, capillary pores, and entrapped air. In hydrated cement paste, gel water is held within the cement hydration products. Physically entrapped or adsorbed water also supports the hydration process. As cement hydrates, the space needed for the products from a cubic centimeter of cement is estimated to double. Capillary pores are the open spaces left inside the hydrated paste. Their size depends mainly on the...

pore size distribution

Concrete Porosity and Durability

Concrete porosity and durability depend strongly on pore size distribution in hardened cement paste. Capillary pores are much larger than gel pores, and in partially hydrated cement paste they form a connected network that lowers strength and raises permeability. Higher permeability makes concrete more vulnerable to freeze-thaw damage and chemical attack. The risk also depends on the water-to-cement ratio. A higher ratio can leave more space for capillary pores to remain open. As cement...

microcracking in concrete

Concrete can develop tiny cracks before any outside load is applied. These microcracks usually form at the boundary between coarse aggregate and hydrated cement paste. They often result from small volume changes caused by stress-strain differences, heat, and moisture movement. At first, these microcracks stay stable. They usually do not grow much until the concrete reaches about 30 percent of its ultimate strength. As the load rises, the material can begin to change more quickly. When...

water cement ratio

Concrete Strength and Water Balance

Concrete strength depends on the balance between water and cement in the mix. This water-cement ratio is the weight of water compared with the weight of cement. It affects strength, durability, and how well concrete resists environmental stress. Abrams’ law shows that less water usually makes stronger concrete. Water is still needed for hydration, which is the chemical process that binds water and cement. It also helps the mix stay workable and compactable. Some water must be absorbed into the...

aggregate cement ratio

How Mix Ratio Changes Concrete Strength

The aggregate cement ratio changes how concrete performs. It is the weight of aggregate divided by the weight of cement in a concrete mix. This ratio affects strength, workability, and durability, so it is an important part of concrete design. A higher aggregate cement ratio makes the mix leaner. Lean mixes have less cement paste to coat and lubricate the aggregate, so they can be harder to work with. At the same time, they may increase strength because the concrete has less total porosity, or...

transition zone

Concrete Transition Zone and Its Porosity

The concrete transition zone is the thin region where aggregate meets cement paste. It has more pores than the surrounding material, so it is usually weaker at first. The bond around the aggregate comes mainly from Van der Waals forces, which are weak attraction forces between particles. When concrete is compacted, this zone often has a higher water-cement ratio near the aggregate. That extra water can form thin water films around the coarse aggregate. These films increase porosity and help...

relation between tensile strength and compressive strength of concrete

relation-between-tensile-strength-and-compressive-strength-of-concrete

Concrete Strength Testing: Tension vs. Compression

Concrete strength testing compares tensile strength and compressive strength. These two properties are related, but they do not rise at the same rate. Tensile strength usually grows more slowly than compressive strength, so the balance between them changes as concrete gets stronger. Several factors affect tensile strength measurements. The test method, specimen size and shape, aggregate texture, and moisture content can all change the result. Direct tension tests are difficult to perform...

fatigue strength of concrete

Concrete Fatigue Under Repeated Loads

Concrete fatigue describes how concrete can weaken or fail when loads are applied again and again, even when each load is below the material’s strength limit. This property matters because it affects the durability and service life of concrete structures. In materials science and engineering, fatigue is a key reason concrete may not last as long as expected under real use. Concrete can fail in two main ways through fatigue. Static fatigue, also called creep rupture, happens under a constant...

impact strength of concrete

Concrete Impact Resistance in Real Use

Concrete impact resistance matters when a material must handle repeated blows and sudden loads. It is important during pile driving, where concrete piles are driven into the ground. It also matters for machinery foundations that experience impulsive loads and for precast concrete parts that can be damaged during handling. Impact strength is measured by checking how well concrete absorbs energy from repeated impacts. A major sign of serious damage is when the concrete does not rebound after...

abrasion resistance of concrete

Concrete Wear Tests and Surface Durability

Concrete wear tests show how well a surface can stand up to abrasion and long-term use. Abrasion is the wearing away of a material by rubbing, scraping, or contact with moving solids. This property matters because concrete surfaces can lose material under vehicle traffic or when solids carried in water brush against them. The transcript describes three tests used to measure concrete abrasion resistance. In the revolving disc test, three plates rotate against the concrete, and silicon carbide...

reinforcements in concrete

Steel Bars in Concrete Structures

Steel bars in concrete structures help the material carry both compression and tension. Concrete is strong when it is squeezed, but it is weak when pulled. Rebar, or reinforcing steel bars, is placed inside the concrete to handle those tensile forces. Steel is a practical choice because it has a similar coefficient of thermal expansion to concrete. That means both materials expand and contract in a similar way as temperature changes. The steel used for reinforcement is usually made by a...

fiber reinforced concrete

Concrete Strength with Added Fibers

Fiber-reinforced concrete is concrete that includes added fibers to improve strength and durability. It uses hydraulic cement with fine or coarse aggregates, plus separated, non-continuous fibers mixed through the material. These fibers can come from steel, glass, and polymers, as well as natural sources such as sisal and cellulose or manufactured sources such as polypropylene and Kevlar. Steel fibers are often preferred because they are strong and tough. They help concrete resist cracking and...

prestressed concrete

How Concrete Is Preloaded for Strength

Prestressed concrete is a construction method that preloads concrete so it can handle more stress. High-strength steel strands are stretched before or after the concrete is loaded in service. The goal is to put the concrete into compression. That compression helps balance the tension the structure will face later. By reducing tension, prestressing helps limit cracks in the concrete. It can also let a structure carry greater loads or span longer distances than conventional reinforced concrete.

ferrocement

Ferrocement Mesh and Mortar Design

Ferrocement is a construction material made from dense layers of mesh or fine rods covered fully in cement mortar. It is a form of reinforced concrete, but it uses mesh instead of the larger steel bars found in standard reinforced concrete. This structure gives ferrocement its thin, flexible form. The material is built from wire meshes and a mortar made of cement and sand. The mortar is usually mixed in a 1:2 or 1:3 ratio. The water-to-cement ratio is kept between 0.40 and 0.45. This helps the...

non-destructive tests for concrete strength

non-destructive-tests-for-concrete-strength

Concrete Strength Checks Without Breaking It

Concrete strength can be checked without fully breaking the material. Two common methods are the rebound hammer test, also called the Schmidt hammer test, and the penetration resistance test, also called the Windsor Probe test. Both are used to estimate the strength of existing concrete. The rebound hammer test measures the hardness of the concrete surface and gives an indirect clue about strength. A spring-driven mass moves inside a tubular housing and strikes a plunger against the concrete.

key terms and concepts

Learn how microcracks form in concrete, how they grow under load, and how ultrasonic and acoustic emission tests can detect early damage.

How Concrete Cracks Before Failure | JoVE K12

JoVE Core Civil Engineering offers a foundational exploration of essential construction materials such as bricks, stones, steel, wood, and concrete, along with fluid mechanics topics like flow over immersed bodies, open channel flow, and dimensional modeling. It also covers key surveying concepts, including leveling, traverse adjustments, curve design, topographic mapping, and geospatial technologies (GPS & GIS). Science-in-action videos showcase laboratory research on materials, fluids, and surveying practices in real-world engineering systems.

civil engineering

How Concrete Cracks Before Failure

Description

Transcript