Name: heat, work, and internal energy
Uploaded: 2023-04-30T12:31:34.000Z
Duration: 1 min 17 s
Channel: JoVE

K12 Standards

Virginia  Standards of Learning

HIgh School

Physical Science

PS.5

PS.5.b

First Law of Thermodynamics

Weźmy pod uwagę latarnię na niebie ze świecą. Ciepło świecy zwiększa energię wewnętrzną cząsteczek powietrza wewnątrz latarni, co powoduje rozszerzanie się powietrza i nadmuchiwanie latarni. Ze względu na rozszerzanie się praca jest wykonywana przez cząsteczki powietrza na latarni. Gęstość powietrza wewnątrz napompowanej latarni jest zmniejszona, co powoduje powstanie siły nośnej.
W tym przykładzie zmiana energii wewnętrznej systemu jest równa wymianie ciepła netto do systemu pomniejszonej o pracę netto wykonaną przez system. Równanie to jest uogólnioną formą zachowania energii znaną jako pierwsza zasada termodynamiki.
Konwencjonalnie Q jest dodatnie lub ujemne, w zależności od tego, czy ciepło jest dodawane do systemu, czy usuwane z systemu. Ponadto W jest dodatnie, gdy praca jest wykonywana przez system i ujemna, gdy praca jest wykonywana w systemie.
W każdym procesie termodynamicznym zmiana energii wewnętrznej jest niezależna od ścieżki i zależy tylko od początkowego i końcowego stanu równowagi układu. Zatem energia wewnętrzna jest funkcją stanu.

<ol>
	<li>Young, H. D i Freedman, R.A. (2012). Fizyka uniwersytecka z fizyką współczesną. San Francisco, Kalifornia: Pearson. str. 630.</li>
	<li>Protokół OpenStax. (2019). Fizyka uniwersytecka Vol. 2. [Wersja internetowa]. str. 116 Źródło <a href="https://openstax.org/books/college-physics/pages/15-1-the-first-law-of-thermodynamics">https://openstax.org/books/college-physics/pages/15-1-the-first-law-of-thermodynamics</a></li>
</ol>

pierwsza zasada termodynamiki

Zmiana energii wewnętrznej układu zależy od transferu ciepła netto do układu i pracy netto wykonanej przez układ. Pierwsza zasada termodynamiki, będąca uogólnioną formą zachowania energii, wiąże te trzy wielkości matematycznie. Stwierdza, że ​​zmiana energii wewnętrznej jest równa różnicy między przekazywaniem ciepła a pracą wykonaną przez układ.

Zastosowane ciepło zwiększa energię wewnętrzną systemu. W związku z tym tradycyjnie ciepło jest uważane za dodatnie, gdy jest dodawane do układu, a ujemne, gdy jest usuwane z układu. Kiedy gaz się rozszerza, działa, a jego energia wewnętrzna maleje. Zatem za pracę uważa się dodatni, gdy robi to system, i ujemny, gdy robi to system.

Chociaż zarówno ciepło, jak i praca zależą od ścieżki termodynamicznej pomiędzy dwoma stanami równowagi, zmiana energii wewnętrznej zależy tylko od początkowego i końcowego stanu równowagi układu. Podobnie jak zmiana energii potencjalnej, zmiana energii wewnętrznej jest wielkością niezależną od ścieżki. Energia wewnętrzna jest funkcją zmiennych termodynamicznych, takich jak ciśnienie, temperatura i objętość. Funkcje takie jak energia wewnętrzna i energia potencjalna nazywane są funkcjami stanu, ponieważ ich wartości zależą wyłącznie od stanu układu.

Pierwsza zasada termodynamiki

Zmiana energii wewnętrznej systemu zależy od wymiany ciepła netto do systemu i pracy netto wykonanej przez system. Pierwsze prawo ...

Education

JoVE Core

Physics

Fizyka

Unit 1

Jednostka 1

The First Law of Thermodynamics

KEY TERMS AND CONCEPTS

Kluczowe terminy i pojęcia

heat, work, and internal energy

Heat, work, and internal energy are linked by the first law of thermodynamics. This law is a generalized form of energy conservation. It explains how energy changes when heat is added to or removed from a system, and when the system does work or has work done on it.

The change in internal energy equals the heat transferred into the system minus the work done by the system. Added heat increases internal energy. For that reason, heat is taken as positive when it enters the system and negative when it leaves.

Work follows the same sign idea. When a gas expands, it does work on its surroundings, and its internal energy decreases. So work is positive when done by the system and negative when done on the system.

Heat and work depend on the path taken between two equilibrium states. Internal energy does not. It depends only on the initial and final equilibrium states, so it is a path-independent quantity, like potential energy.

Internal energy is a function of thermodynamic variables such as pressure, temperature, and volume. Quantities like internal energy and potential energy are called state functions because their values depend only on the state of the system.

Heat, Work, and Internal Energy

thermodynamic systems

Open, Closed, and Isolated Systems

A thermodynamic system is the part of the world that scientists study for its heat and energy behavior. It sits inside a surrounding environment, or surroundings. The system and the surroundings can exchange heat and do work across the boundary that separates them. The immediate surroundings affect the system most strongly because they interact with it directly. A kettle of boiling tea shows how this works in everyday life. The tea and the kettle together form the system. If the lid is open,...

work done during volume change

Gas Work in a Piston Cylinder

Gas work in a piston cylinder describes how pressure and volume change are related in thermodynamics. In mechanics, work happens when a force moves an object. In thermodynamics, work done on a system can be estimated when the system changes volume during a process. A gas can be trapped in a cylinder with a movable piston at one end. When the gas expands from volume V1 to volume V2, it pushes on the piston and moves it by a small distance dr. If the pressure on the piston face is p and the...

path between thermodynamics states

Path Dependence in Gas Work

Work done by an ideal gas can depend on the path it takes between two thermodynamic states. The transcript compares two routes from state A to state C for the same gas. In both cases, the gas expands from volume V1 to volume V2, but the work is not the same. Along path AC, the gas stays at constant temperature T. It expands from V1 to V2. The work done by the gas is found from the pressure-volume relation for an ideal gas. After substituting pressure as nRT/V and integrating, the work for this...

heat and free expansion

Two Gas Paths to the Same Volume

Heat added to a thermodynamic system can lead to the same final state through different paths. The path matters because work and heat depend not only on the initial and final states, but also on the steps in between. In this topic, an ideal gas is used to show two different ways to reach the same volume. In the first case, the gas is in a cylinder with a piston and is heated at a constant temperature. As the gas molecules absorb energy, the gas expands slowly in a controlled isothermal process.

internal energy

How Internal Energy Changes in Gas Systems

Internal energy is the energy stored inside a thermodynamic system. It is the sum of the kinetic and potential energies of the molecules or other particles in the system. Molecular kinetic energy includes translational motion, rotation, and vibration. Molecular potential energy comes from interactions between molecules. A system’s location and overall motion do not affect its internal energy. For an ideal monatomic gas, each particle is a single atom. That means there is no rotational or...

first law of thermodynamics

Heat, work, and internal energy are linked by the first law of thermodynamics. This law is a generalized form of energy conservation. It explains how energy changes when heat is added to or removed from a system, and when the system does work or has work done on it. The change in internal energy equals the heat transferred into the system minus the work done by the system. Added heat increases internal energy. For that reason, heat is taken as positive when it enters the system and negative...

first law of thermodynamics: problem-solving

first-law-of-thermodynamics-problem-solving

First Law of Thermodynamics: Solving Problems

The first law of thermodynamics links internal energy, heat, and work. It states that the change in internal energy of a system equals the net heat transfer into the system minus the net work done by the system. This is a general form of energy conservation, and it can be used for any thermodynamic process. To solve a first-law problem, start by identifying the thermodynamic system. Then list the initial and final states of the process. Next, identify the known and unknown quantities. It is...

cyclic processes and isolated systems

Net Work in a Cyclic Thermodynamic Process

A cyclic thermodynamic process returns a system to its initial state. In a cycle, the change in internal energy is zero. An isolated system is different because it has zero heat exchange and zero work, so its internal energy stays constant. For a non-isolated system, the internal energy change is zero only when the process is cyclic. The first law of thermodynamics relates internal energy, heat transfer, and work. It states that the change in internal energy is the difference between the net...

isothermal processes

Isothermal Expansion and Heat Transfer

An isothermal process is a thermodynamic process that happens at constant temperature. During the process, heat slowly flows into the system or out of the system so thermal equilibrium is maintained. Phase changes are common examples of isothermal processes. Water can evaporate into steam at a constant temperature, and water can also freeze into ice at a constant temperature. An ideal gas can also undergo isothermal expansion or compression. Here, an ideal gas in an isolated cylinder expands...

isochoric and isobaric processes

Constant Volume and Pressure in Thermodynamics

Thermodynamic processes can happen at constant volume or at constant pressure. An isochoric process is a constant-volume process. In this case, the volume does not change, so the work done by the system is zero. The first law of thermodynamics still applies, so any heat added or removed changes the internal energy of the system only. A simple example is heating 1000 g of water from 40 degrees celsius to 70 degrees celsius at constant volume. Because the process is isochoric, no work is done by...

heat capacities of an ideal gas i

Ideal Gas Heat Capacity at Constant Pressure

Heat capacity describes how much heat a substance absorbs for a given change in temperature. It is also called thermal capacity, and its SI unit is J/K. Specific heat capacity is the heat needed to raise the temperature of 1 kg of a substance by 1 K, and its SI unit is J/kg·K. The video also explains molar heat capacity. This is the amount of heat added or removed to change the temperature of 1 mole of a substance by 1 K. It can be measured at constant volume or constant pressure, and it is...

heat capacities of an ideal gas ii

Ideal Gas Heat Capacity Differences

Ideal gas heat capacities depend on whether the gas is heated at constant volume or constant pressure. At constant volume, the heat absorbed only raises the internal energy of the system. No work is done in this case. At constant pressure, the situation is different. The heat absorbed increases the internal energy and also does work. Molar heat capacity is the heat needed to raise the temperature of 1 mole of gas by 1 unit. Because some of the added heat goes into work, more heat is needed at...

heat capacities of an ideal gas iii

Ideal Gas Heat Capacity and Degrees of Freedom

Ideal gas heat capacity depends on degrees of freedom, which are the independent ways a gas molecule can move, rotate, and vibrate. If d is the number of degrees of freedom, the molar heat capacity at constant volume can be written in terms of d. The molar heat capacity at constant pressure can also be written using the relationship between the two heat capacities. The ratio of molar heat capacity at constant pressure to molar heat capacity at constant volume is called the ratio of heat...

adiabatic processes for an ideal gas

Gas Temperature Changes in Adiabatic Processes

Adiabatic processes change the temperature of an ideal gas without heat transfer. In an adiabatic compression, no heat is added, but work is done on the gas. That work raises the gas temperature. In an adiabatic expansion, the gas does work and its temperature drops. A common example is the compression of a gas-air mixture inside a car engine cylinder. The compression happens so quickly that there is no time for heat to move between the mixture and its surroundings. Even so, the work done on...

pressure and volume in an adiabatic process

pressure-and-volume-in-an-adiabatic-process

Free Expansion: Pressure, Volume, and Temperature

Free expansion shows how pressure, volume, and temperature behave when a gas expands without doing work. It is an adiabatic process, but it is not the same as adiabatic expansion. In free expansion, no work is done and the internal energy does not change. In adiabatic expansion, work is done and the internal energy changes. For an adiabatic process, the pressure-volume relation comes from the adiabatic condition. That relation does not apply to free expansion, even though the expansion is...

work done in an adiabatic process

Adiabatic Compression in an Engine Cylinder

Adiabatic compression in an engine cylinder changes the pressure, temperature, and volume of a gas-air mixture. In this setup, gasoline vapor is injected into the cylinder when the piston is in its expanded position. The mixture starts at 20 °C, 1.00 x 10^5 N/m^2, and 240 cm^3. The mixture is then compressed adiabatically to 40 cm^3. Adiabatic means no heat is exchanged with the surroundings during the process. For this calculation, the compression is treated as quasi-static, even though real...

thermodynamic potentials

Energy Forms in Thermodynamics

Thermodynamic potentials are energy-based state functions used to analyze a thermodynamic system. They help describe how a system changes under different conditions. The four main thermodynamic potentials are internal energy, enthalpy, Helmholtz free energy, and Gibbs free energy. These potentials can be written using two of the variables pressure, volume, temperature, and entropy. In each case, the rate of change of the potential with respect to the other two variables gives useful...

maxwell's thermodynamic relations

Using Maxwell's Relations in Thermodynamics

Maxwell's thermodynamic relations help solve problems in thermodynamics. They connect partial differentials for quantities that are hard to measure in the lab with quantities that are easier to measure. This makes them useful for working with temperature, pressure, volume, and entropy. These relations come from thermodynamic potentials and the symmetry of second derivatives. Thermodynamic potentials are exact differentials, so the order of second differentiation does not change the result.

joule-thomson effect

Gas Cooling and Heating in Throttling

Gas cooling and heating in throttling is explained by the Joule-Thomson effect, also called the Joule-Kelvin effect. It describes how a fluid changes temperature when it passes through a valve or porous plug in a thermally insulated system. This type of flow is called a throttling process. In the experiment, a high-pressure gas is forced through a throttle valve or porous plug into a lower-pressure region. The gas expands as it moves into the larger volume. Work is done on the gas as it is...

key terms and concepts

Learn how heat, work, and internal energy connect through the first law of thermodynamics, including sign conventions and state functions.

Heat, Work, and Internal Energy | JoVE K12

physics

JoVE Core Physics introduces the theory and application of fundamental physics topics, including kinematics, dynamics, fluid mechanics, statics, waves, and acoustics, with concise and easy-to-understand animated videos. Additionally, the scientist-in-action videos demonstrate the application of related concepts in classical and original research experiments performed in today's laboratories worldwide.

Minnesota Academic Standards in Science

9-12

2.2.1 9P.2.1.1.1

new-jersey-student-learning-standards-for-science

New Jersey Student Learning Standards for Science

High School

Energy

HS-PS3-1

Arizona Science Standards

HS.P4

HS.P4U1.8

HS+Phy.P4

HS+Phy.P4U1.6

Florida Department of Education

SC.912.P.10

SC.912.P.10.2

new-york-state-science-learning-standards

New York State Science Learning Standards

HS. Energy

HS-PS3-3.

The universe is composed of matter in different forms, and all forms of matter contain energy.&#160; The different forms of energy on Earth originate from ...

Conservation of Mechanical Energy

The mechanical energy E of a system is the sum of its potential energy U and the kinetic energy K of the objects within it. What happens to this ...

/files/media/science-education/science-education-thumbs/14702.jpg

Conservation of Energy

The terms &#39;conserved quantity&#39;&#160;and &#39;conservation law&#39;&#160;have specific scientific meanings in physics, which differ from the ...

Conservation of Energy: Application

When solving problems using the energy conservation law, the object (system) to be studied should first be identified. Often, in applications of energy ...

The student will investigate and understand that energy is conserved. Key ideas include energy can be stored in different ways;

PS.5.a

Mechanisms of Heat Transfer I

Just as interesting as the effects of heat transfer on a system are the methods by which the heat transfer occur. Whenever there is a temperature ...

Mechanisms of Heat Transfer II

In convection, thermal energy is carried by the large-scale flow of matter. Ocean currents and large-scale atmospheric circulation, which result from the ...

conduction-convection-and-radiation-problem-solving

Conduction, Convection and Radiation: Problem Solving

There are three methods by which heat transfer can take place: conduction, convection, and radiation. Each method has unique and interesting ...

Heat Flow and Specific Heat

Heat is a type of energy transfer that is caused by a temperature difference, and it can change the temperature of an object. Since heat is a form of ...

A change in the internal energy of a system depends on the the net heat transfer into the system and the net work done by the system. The first law of ...

statements-of-the-second-law-of-thermodynamics

Statements of the Second Law of Thermodynamics

The second law of thermodynamics can be stated in several different ways, and all of them can be shown to imply the others. The Clausius&#8217; statement ...

Energy Transfer in Chemical Reactions

Chemical reactions require sufficient energy to cause the matter to collide with enough precision and force that old chemical bonds can be broken and new ...

Trophic Efficiency

Trophic level transfer efficiency (TLTE) is a measure of the total energy transfer from one trophic level to the next. Due to extensive energy loss as ...

The student will investigate and understand that energy is conserved. Key ideas include energy is transferred and transformed; and

Heat Engines

A heat engine is a device used to extract heat from a source and then convert it into mechanical work used for various applications. For example, a steam ...

Internal Combustion Engine

The internal combustion engine is a heat engine that uses the byproducts of combustion as the working fluid instead of using a heat transfer medium to ...

The Carnot Cycle

Converting work to heat is an irreversible process, and the purpose of a heat engine is to reverse the effect partially. Heat engines aim to increase the ...

The student will investigate and understand that energy is conserved. Key ideas include energy can be transformed to meet societal needs.

PS.5.c

Heat, Work, and Internal Energy

Description

Transcript

Tags

More videos by Standards