Name: brick sizes and modular masonry
Uploaded: 2024-09-12T16:16:25.000Z
Duration: 1 min 21 s
Channel: JoVE

K12 Standards

Texas Essential Knowledge and Skills

High School

Physics

PHYS.2

PHYS.2.A

Brick Sizes

Размеры кирпича определяются тремя измерениями: его шириной, высотой и длиной.
Как правило, кирпичи имеют размеры для строительства стен в виде модулей шириной 4 дюйма или 8 дюймов или кратно этим размерам.
Кирпичи, подходящие под эти размеры, известны как модульные кирпичи. Номинальный размер кирпича относится к его указанному размеру, который включает в себя толщину растворного шва, используемого при строительстве.
Кирпичи бывают разных размеров, включая, помимо прочего, модульные, модульные инженерные, модульные закрытия, римские, нормандские, коммунальные и меридианальные.
Номинальные размеры хозяйственных кирпичей составляют примерно 4 дюйма в высоту и ширину и 12 дюймов в длину. Эти размеры включают в себя толщину раствора.
Ровно четыре с половиной модульных кирпича требуется для комплектации площади, покрытой двумя хозяйственными кирпичами. Стена, сделанная из больших кирпичей, может изменить то, как наблюдатели воспринимают размер стены.
Для зданий с уникальными деталями, украшениями или нетрадиционными формами часто необходимы нестандартные размеры и формы кирпича, чтобы вместить эти отличительные архитектурные элементы.

Размеры кирпича

Размер кирпича играет решающую роль в строительстве, влияя как на эстетику, так и на структурную целостность зданий. Кирпичи определяются тремя параметрами: шириной, толщиной и длиной. Обычно они проектируются с учетом модульных измерений, как правило, кратных 10,16 или 20,32 сантиметрам в ширину, чтобы обеспечить единообразие конструкции и совместимость с другими строительными материалами.

Модульные кирпичи являются наиболее распространенным типом и имеют размер, включающий растворный шов, который необходим для связывания в каменной кладке. Номинальный размер кирпича относится к его размеру, включая этот растворный шов. Различные типы кирпичей, такие как Engineer Modular, Closure Modular, Roman, Norman, Utility и Meridian, удовлетворяют различные структурные и эстетические потребности.

Например, кирпичи хозяйственного назначения больше по размеру; обычно они имеют высоту около 10,16 см и длину 30,48 см. Их больший размер уменьшает количество кирпичей, необходимых для кладки, тем самым снижая затраты на рабочую силу и повышая прочность стены на сжатие за счет минимизации использования раствора. Один такой кирпич покрывает ту же площадь, что и четыре с половиной модульных кирпича, влияя на визуальное восприятие масштаба стены.

Кирпичи нестандартного размера часто производятся для уникальной детализации. Эти специальные кирпичи помогают достичь определенных визуальных и функциональных результатов, желаемых в уникальных конструкциях, обеспечивая большую гибкость в дизайне при решении конкретных структурных требований.

Размеры кирпича определяются тремя измерениями: его шириной, высотой и длиной.
Как правило, размер кирпича рассчитан на возведение стен в модулях по 4 ...

Education

JoVE Core

Civil Engineering

Unit 1

Раздел 1

Masonry Materials

Материалы для каменной кладки

KEY TERMS AND CONCEPTS

ОСНОВНЫЕ ТЕРМИНЫ И ПОНЯТИЯ

brick sizes and modular masonry

Brick sizes are important in construction because they affect both the look of a building and its structural strength. Bricks are measured by three dimensions: width, thickness, and length. Builders often design them to fit modular measurements, usually in multiples of 4 inches or 8 inches in width, so they work well with other building materials.

Most bricks are modular bricks. These bricks are sized to include the mortar joint, which is the layer of mortar that bonds masonry units together. The nominal size of a brick is its dimension including that mortar joint. This sizing system helps builders create uniform walls with consistent spacing and fit.

Several brick types meet different building needs. Engineer Modular, Closure Modular, Roman, Norman, Utility, and Meridian bricks are all used for structural or visual purposes. Utility bricks are larger than standard modular bricks. They are usually about 4 inches high and 12 inches long, so fewer bricks are needed during masonry work.

Using utility bricks can lower labor costs because fewer units must be placed. Their larger size can also increase a wall’s compressive strength by reducing the amount of mortar used. One utility brick covers the same area as four and a half modular bricks, which can also change how large a wall appears. For special projects, custom-sized bricks can be made to achieve unique details and meet specific design or structural needs.

Brick Sizes and Modular Masonry

masonry

Masonry Materials and Structural Uses

Masonry uses stone and man-made units such as bricks, clay tiles, terra cotta, and concrete blocks to build structures. These units can form walls, floors, and arches. Masonry is valued for strength, durability, and a wide range of visual finishes. The units are laid in rows called coursing. Mortar, a mix of water, cement, and sand, binds the units together. Building with masonry is hands-on and can be done with basic tools. A trowel applies mortar, a hammer helps adjust placement, and levels...

mortar

Mortar in Masonry: Strength and Finish

Mortar is a key construction material used to bind masonry units together. It is made from Portland cement, hydrated lime, sand, and water. In walls, it fills gaps between units and helps spread weight more evenly across the structure. That reduces weak spots and supports a stronger build. Mortar also protects masonry from outside conditions. It acts as a barrier against water and wind, which helps safeguard the inside of the structure. It can also help correct surface irregularities in...

mortar properties

How Mortar Performance Is Measured

Mortar performance is measured by several key properties that matter in masonry work. These include workability, water retention, bond strength, durability, compressive strength, volume change, and appearance. Together, these properties help determine how well mortar can be placed, bonded, and finished. Workability is the ability of mortar to be applied and moved easily. Good workability means the mortar spreads smoothly and does not sag or fall off the surface. This helps masonry units stay...

bricks

How Bricks Are Made and Fired

Bricks are made from fired clay and come in many shapes, sizes, and colors. They are a basic building material used in construction. The brickmaking process begins with local clay or shale, which is crushed, ground, and screened to make a fine material. Next, the refined clay is mixed with water to form a workable mass. That mixture can be shaped in three main ways: soft mud, dry press, or stiff mud. Soft mud bricks are made in molds with high moisture content. They may be water-struck or...

brick sizes

Brick sizes are important in construction because they affect both the look of a building and its structural strength. Bricks are measured by three dimensions: width, thickness, and length. Builders often design them to fit modular measurements, usually in multiples of 4 inches or 8 inches in width, so they work well with other building materials. Most bricks are modular bricks. These bricks are sized to include the mortar joint, which is the layer of mortar that bonds masonry units together.

brick classifications

Types of Bricks in Construction

Bricks used in construction are grouped by where they are used and by their structure. The main types include facing bricks, building bricks, hollow bricks, paving bricks, and firebricks. These categories show how one material can serve different jobs in a structure. Facing bricks, also called face bricks, are used where both strength and appearance matter. They form the visible surface of a wall, so their look is important. Building bricks are usually placed in hidden parts of a structure,...

brick durability, strength, and appearance

How Brick Quality Affects Masonry Performance

Brick quality affects how masonry holds up, looks, and performs over time. Durability, strength, and appearance are all used to judge which bricks fit a specific job. These features help builders choose bricks for walls, facades, and other construction uses. Durability is closely tied to freeze-thaw action. In freeze-thaw, water absorbed by a brick expands when it freezes. That expansion can damage the brick, especially if the water melts and refreezes. Bricks are graded for durability as SW,...

brick masonry

Brick Wall Bonds and Wythes

Brick masonry is built from individual bricks set in mortar to form walls. A key unit in this system is the wythe, which is a vertical layer of bricks one brick thick. Inside a wythe, bricks can be arranged in different courses, or rows, to build the wall. The most common course is the stretcher course. In this pattern, each brick lies with its long edge horizontal and its face parallel to the wall. Thicker walls are made by joining multiple wythes together. Builders use headers, which are...

brick cutting techniques

Brick Cuts for Fitting Wall Spaces

Brick cuts help fit bricks into small spaces in a wall. A mason uses a hammer with a chisel-pointed end for basic shaping. The mason strikes the brick with sharp, precise blows. For more exact cuts, a power saw with a water-cooled diamond blade is used. Cut bricks are also named by size. A half-bat is a brick cut to half its original length. A three-fourth bat is cut to three-fourths of its length. These cut pieces help fill gaps and keep the wall pattern aligned. Some cuts are made for...

mortar joints in brick masonry

Mortar Joint Profiles and Brick Finishing

Mortar joints hold brick masonry together and help give the wall strength. They fill the spaces between bricks and support the finished structure. Joint thickness can vary from less than one-fourth inch to more than half an inch, depending on the need and the application. As the mortar starts to harden, workers tool the joints. Tooling means compacting and shaping the mortar. This step improves the look of the brickwork and helps it stand up better to bad weather. Brick masonry can be...

spanning openings in brick walls

Brick Wall Supports for Doors and Windows

Brick wall supports help keep openings for doors and windows stable. These supports hold up the weight of the wall above the opening. The main options are lintels, corbels, and arches. Lintels are the main support used to span an opening. They can be made from reinforced concrete, steel-reinforced brick masonry, or simple steel angles. Lintels are usually easy to install and are often hidden inside the brickwork, so they are not visible in the finished wall. Corbels provide only limited...

reinforced brick masonry

Steel-Reinforced Brick Wall Construction

Steel-reinforced brick wall construction uses steel bars and grout to make masonry walls stronger. The steel can be placed inside the hollow cores of bricks or between two layers of masonry called wythes. Grout, a fluid mix of Portland cement, aggregate, and water, holds the steel and brick together. Deformed steel reinforcement bars are set in the collar joints or in the hollow cores of the bricks. The system includes both vertical and horizontal steel bars. Vertical bars must be at least...

types of building stone

Building Stone Uses and Rock Types

Building stone is a natural construction material cut from rock deposits and shaped into the sizes needed for building work. It is grouped into three main rock types: igneous, sedimentary, and metamorphic. Each group has different properties that make it useful for specific parts of a structure. Igneous rocks form when magma or lava cools and solidifies. Granite is a common example. It is durable and resists weathering, so it works well in parts of buildings that face severe weather. <br...

quarrying of stone

Stone Extraction and Block Shaping

Stone extraction and block shaping begin in a quarry, where large blocks are removed safely and efficiently. Quarry workers may use controlled explosions, but they also use precise cutting and drilling methods. The goal is to separate stone from the rock face without damaging the material. One common method uses a diamond belt saw to make a vertical cut in the quarry face. The blocks can be very large, sometimes about 50 feet long and 12 feet high. After the cut, workers drill at the base of...

stone masonry

Stone Masonry Types and Jointing

Stone masonry is a building method that uses individual stones to form structures. It is usually divided into two main categories: rubble masonry and ashlar masonry. Rubble masonry uses uneven, naturally shaped stones. These may be river rocks or fragments from quarries. A mason often has to choose each stone carefully and may shape it to fit the space, even when the stones differ in size and form. Ashlar masonry uses stones that are cut into square or rectangular shapes. This type creates...

manufacture of concrete masonry units

Concrete Block Curing and Block Types

Concrete masonry units are made by mixing stiff concrete from Portland cement, aggregates, and water. The mix is placed into metal molds and vibrated so it settles evenly and does not separate. The wet blocks are then removed from the molds and set on racks. After molding, the blocks are moved to curing. Curing can happen in a steam kiln, where the blocks are steam cured, or in an autoclave, where high-pressure steam curing is used. This step helps the blocks gain the hardness and durability...

laying concrete masonry

Building a Concrete Block Wall

Building a concrete block wall starts with careful base preparation, mortar placement, and block alignment. The area where the wall will be built is cleaned first. Then mortar is spread where the first row of concrete blocks will sit. The first blocks are often set at a corner to mark the wall boundaries. Mortar is placed on the face shells of the blocks, which are the outward-facing surfaces. It is also applied at the ends of each block. This helps form the vertical joints between blocks and...

steel manufacturing

From Iron Ore to Shaped Steel

Steel manufacturing turns iron ore into steel through several controlled stages. It starts in a blast furnace, where iron ore is layered with coke and crushed limestone. The coke is a fuel, and the limestone helps remove unwanted material from the molten metal. Air is blasted into the furnace, and the coke ignites. This produces carbon monoxide, which reduces the iron ore to pure iron. As the iron melts, limestone forms slag. Slag traps impurities such as silica, phosphorus, and alumina. The...

structural steel products

How Structural Steel Shapes Are Made

Structural steel shapes are made in a structural mill. The process starts with a beam blank. The steel is reheated and then sent through a series of rollers that gradually form it into its final shape. The spacing between the rollers can be changed to make different sections with the same nominal dimensions. After shaping, the steel leaves the mill as a continuous length. A hot saw then cuts it into manageable pieces. The cut pieces are cooled and passed through another set of rollers. These...

steel fastening techniques

How Steel Sections Are Joined

Steel sections are joined with rivets, bolts, or welding. Each method fits different structural needs and working conditions. These fastening techniques help assemble strong steel structures in practical ways. Riveting uses cylindrical steel fasteners with a specially designed head. The rivets are heated until white-hot and then placed through pre-drilled holes in the steel sections. A pneumatic hammer shapes the exposed end into a second head, which locks the pieces together. Bolting is...

mechanical characteristics of steel

Testing Steel for Strength and Toughness

Steel is tested for strength, toughness, and flexibility using several standard mechanical tests. These tests help show how steel will behave in real use. They also help engineers choose steel for the right job. A tension test measures tensile strength. In this test, a steel specimen is pulled in a gripping device until it breaks. The results are used to draw a stress-strain curve. That curve shows the proportional limit, yield point, ultimate strength, and the point of rupture. A torsion...

key terms and concepts

Learn how brick sizes, modular measurements, mortar joints, and special brick types affect wall strength, cost, and design in construction.

Brick Sizes and Modular Masonry | JoVE K12

JoVE Core Civil Engineering provides a foundational exploration of essential construction materials in civil engineering, focusing on bricks, stones, steel, wood, and concrete through easy-to-understand animated videos. This collection covers the properties, manufacturing processes, and practical applications of these materials. Additionally, the accompanied science-in-action videos demonstrate the research experiments performed in laboratories.

civil engineering

Chemistry and Physics

IPC.2

IPC.2.A

Models, Theories, and Laws

Scientists frequently use models to help them comprehend a specific collection of phenomena. In physics, a model is a condensed version of a physical ...

/files/media/science-education/science-education-thumbs/14686.jpg

The dimensions of a brick are determined by three measurements: its width, height, and length.
Typically, bricks are sized to build walls in modules of 4 ...

structural-properties-and-dimensions-of-lumber

Structural Properties and Dimensions of Lumber

Wood fibers align along the tree&#39;s length, giving it up to twenty times higher tensile strength along the fibers than across them. Wood is also ...

Accuracy, limits, and approximation

Accuracy, limits, and approximations are common in many fields, especially in engineering calculations. These concepts are imperative for ensuring that a ...

Design Consideration

While designing a structure, the considerations start with the ultimate strength of a material, which is determined through tests, measuring changes under ...

Dynamics of Structures

Source:&#160;Roberto Leon, Department of Civil and Environmental Engineering, Virginia Tech, Blacksburg, VA
It is rare nowadays that a whole year goes by ...

Material Constants

Source:&#160;Roberto Leon, Department of Civil and Environmental Engineering, Virginia Tech, Blacksburg, VA
In contrast to the production of cars or ...

Estimation of the Physical Quantities

On many occasions, physicists, other scientists, and engineers need to make estimates of a particular quantity. These are sometimes referred to as ...

/files/media/science-education/science-education-thumbs/14734.jpg

Identify advantages and limitations of models such as their size, scale, properties, and materials

Introduction to Statistics

The science of statistics involves collecting, analyzing, interpreting, and presenting data. The method of collecting, organizing, and summarizing data is ...

How Data are Classified: Categorical Data

A variable, usually notated by capital letters such as X and Y, is a characteristic or measurement that can be determined for each member of a population. ...

How Data are Classified: Numerical Data

Data that are countable or measurable in specific units are called numerical or quantitative data. Quantitative data are always numbers. Quantitative data ...

Review and Preview

Data are individual items of information obtained from a population or sample. Data may be classified as qualitative (categorical), quantitative ...

What is a Frequency Distribution

A frequency is the number of times a value of the data occurs. The sum of all the frequency values represents the total number of students included in the ...

What is Central Tendency?

Descriptive statistics describe or summarize relevant characteristics of a sample and aid in the analysis of data of interest. When analyzing large ...

Arithmetic Mean

The arithmetic mean is the most commonly used measure of the central tendency of a data set. It is defined as the sum of all the elements constituting the ...

What is a Mode?

The mode is one of the commonly used measures of a central tendency. It is defined as the most frequent value in a data set.
There can be more than one ...

Median

Besides mean, the median is a widely used measure of central tendency. Typically, median is defined as the central or middle value of a data set, measured ...

What is Variation?

Apart from the measures of central tendency, distribution, outliers, and the changing characteristics of data with time, an important characteristic of ...

Standard Deviation

The most commonly used measure of variation is the standard deviation. It is a numerical value measuring how far data values are from their mean. The ...

Standard Error of the Mean

The sampling variability of a statistic is defined as how much the statistic varies from one sample to another. The sampling variability of a statistic is ...

Calculating Standard Deviation

The standard deviation is the most common measure of variation. It is a value that tells us how far a data value is from the mean value in a dataset. ...

Variance

&#160;The deviations show how spread out the data are about the mean. A positive deviation occurs when the data value exceeds the mean, whereas a negative ...

Coefficient of Variation

The coefficient of variation measures the dispersion of the data points or distribution around the mean. Using the coefficient of variation, we can ...

Probability in Statistics

Probability is the likelihood of an event occurring. The term event is defined as a collection of results of a procedure. An event is a simple event when ...

Random Variables

A random variable is a single numerical value that indicates the outcome of a procedure. The concept of random variables is fundamental to the probability ...

What is a Hypothesis?

A hypothesis can be a simple sentence or statement about a property or any phenomenon observed or predicted for a population. It is usually a claim about ...

Null and Alternative Hypotheses

The actual hypothesis testing begins by considering two hypotheses. They are termed&#160; the null hypothesis and the alternative hypothesis. These ...

Types of Hypothesis Testing

There are three types of hypothesis tests: right-tailed, left-tailed, and two-tailed.
When the null and alternative hypotheses are stated, it is observed ...

Study Design in Statistics

A study design is a set of techniques that allow a researcher to collect and analyze data from different variables defined for a specific research ...

types-of-errors-detection-and-minimization

Types of Errors: Detection and Minimization

Error is the deflection of an obtained result from the expected or true results of an experiment. This happens due to the uncertainty associated with the ...

systematic-error-methodological-and-sampling-errors

Systematic Error: Methodological and Sampling Errors

Systematic errors, depending on their source, are of four types &#8211; sampling, instrumental, method, and personal errors.
Sampling errors occur due to ...

Random Error

Indeterminate or random errors arise from several uncontrollable variables in successive measurements.
Since these errors can neither be predicted nor ...

Analyze data by identifying significant statistical features, patterns, sources of error, and limitations

PHYS.2.B

Numerical Calculations

In engineering applications, the representation of the numerical value is critical. Presenting or reporting the answer is one of the essential parts of ...

Quantitative Analysis

Quantitative analysis is a technique for measuring the amount of specific constituents in a sample. When the sample&#39;s composition is unknown, ...

Statistical Analysis: Overview

An analysis is usually conducted by replicated sampling or repeated measurements on the same sample. This leads to scattered results rather than a single ...

Dimensional Analysis

Dimensional analysis, also known as the factor label method, is a versatile approach for mathematical operations. The main principle behind this approach ...

calculating-and-interpreting-the-linear-correlation-coefficient

Calculating and Interpreting the Linear Correlation Coefficient

The correlation coefficient, r, developed by Karl Pearson in the early 1900s, is numerical and provides a measure of strength and direction of the linear ...

variation-normal-distribution-range-and-standard-deviation

Variation: Normal Distribution, Range, and Standard Deviation

In the field of psychology, there are&nbsp;several ways to organize measurements of a trait, feature, or characteristic (i.e., variables). Qualitative ...

Regression Analysis

Regression analysis is a statistical tool that describes a mathematical relationship between a dependent variable and one or more independent variables.
...

Microsoft Excel: Regression Analysis

Regression analysis is critical in statistics. Consider the data as shown here in the Microsoft Excel worksheet. The scatter plot of variables has a ...

5-Number Summary

In a dataset, the 5-number summary includes the minimum data value, the data value of the first quartile, the median data value or data value of the ...

The Small x Assumption

If a reaction has a small equilibrium constant, the equilibrium position favors the reactants. In such reactions, a negligible change in concentration may ...

Use mathematical calculations to assess quantitative relationships in data

PHYS.2.C

Experimental Designs

An experimental design is a systematic process that allows researchers to evaluate the relationship between dependent and independent variables. There are ...

from-theory-to-design-the-role-of-creativity-in-designing-experiments

From Theory to Design: The Role of Creativity in Designing Experiments

Source: Laboratories of Gary Lewandowski, Dave Strohmetz, and Natalie Ciarocco&#8212;Monmouth University

Research studies come into being when a ...

aerodynamic-performance-of-a-model-aircraft-the-dc-6b

Aerodynamic Performance of a Model Aircraft: The DC-6B

Source: Jose Roberto Moreto and Xiaofeng Liu, Department of Aerospace Engineering, San Diego State University, San Diego, CA
The low-speed wind tunnel is ...

Design of Prismatic Beams for Bending

The design process for prismatic beams subjected to bending begins by determining the allowable stress for the chosen material.
The allowable stress is ...

Fatigue of Metals

Source: Roberto Leon, Department of Civil and Environmental Engineering, Virginia Tech, Blacksburg, VA
The importance of studying metal fatigue in civil ...

Stress-Strain Characteristics of Steels

Source:&#160;Roberto Leon, Department of Civil and Environmental Engineering, Virginia Tech, Blacksburg, VA
The importance of materials to human ...

Evaluate experimental and engineering designs

PHYS.2.D

Scientific and engineering practices. The student analyzes and interprets data to derive meaning, identify features and patterns, and discover relationships or correlations to develop evidence-based arguments or evaluate designs. The student is expected to:

Brick Sizes and Modular Masonry

Description

Transcript

More videos by Standards