Name: controlling precipitate size in gravimetry
Uploaded: 2024-04-04T10:51:29.000Z
Duration: 1 min 16 s
Channel: JoVE

In precipitation gravimetry, ideally, the precipitant reacts specifically or selectively with the analyte to yield a precipitate with certain attributes.
The obtained precipitate should be either a pure substance of a known composition or easily converted to one by a simple process.
It should also be highly insoluble and completely precipitated. This can be achieved by adding or removing a common ion, and optimizing the reaction pH and temperature.
The particle size of the precipitate is also important.
Colloidal suspensions have very small particles that pass through the filter paper, whereas crystalline suspensions have larger particles that settle quickly and are easily filtered.
Particle size is impacted by multiple factors and can be expressed in terms of the relative supersaturation. Here, Q is the concentration of the solute and S denotes its equilibrium solubility.
Colloidal suspensions form when the relative supersaturation is high, while crystalline suspensions form when the ratio is low.

precipitate formation and particle size control

Precipitate Formation and Particle Size Control

In precipitation gravimetry, the precipitating agent should react specifically or selectively with the analyte. While a specific reagent reacts with the analyte alone, a selective reagent can react with a limited number of chemical species.
The obtained precipitate should be either a pure substance of known composition or easily converted to one by a simple process, such as ignition or drying. In addition, the precipitate should be insoluble and easily filterable. In general, filterability increases with the size of the precipitate particles. Colloidal suspensions contain minuscule particles with diameters varying from 10&#8722;9 to 10&#8722;6 m, which are invisible to the naked eye and not easily filtered. However, crystalline suspensions have larger particles that settle quickly and are readily filtered.
The temperature, precipitate solubility, reactant concentrations, and speed of mixing of reactants can affect the particle size. The overall effect of these attributes is called relative supersaturation, RSS, which can be expressed in terms of the concentration of the solute (Q) and its equilibrium solubility (S). The size of the obtained particles is inversely proportional to the average relative supersaturation when the reagent is added. As a result, when the relative supersaturation ratio is high, colloidal precipitates are favored, while crystalline precipitates with large particle sizes are obtained at low relative supersaturation ratios.&#160;

In precipitation gravimetry, ideally, the precipitant reacts specifically or selectively with the analyte to yield a precipitate with certain attributes.
...

precipitate-formation-and-particle-size-control

Education

JoVE Core

Analytical Chemistry

Unit 1

Complexometric Titration, Precipitation Titration, and Gravimetry

complexometric-titration-precipitation-titration-and-gravimetry

KEY TERMS AND CONCEPTS

controlling precipitate size in gravimetry

Precipitation gravimetry uses a precipitating agent that reacts specifically or selectively with the analyte. A specific reagent reacts with the analyte alone. A selective reagent reacts with a limited number of chemical species.

The precipitate should be a pure substance with a known composition, or it should be easy to convert into one by drying or ignition. It should also be insoluble and easy to filter. Filterability usually improves as particle size increases.

Colloidal suspensions contain very small particles, with diameters from 10^-9 to 10^-6 m. These particles are invisible to the naked eye and are not easy to filter. Crystalline suspensions have larger particles. They settle faster and are easier to filter.

Particle size depends on temperature, precipitate solubility, reactant concentration, and how fast the reactants are mixed. These factors are described together by relative supersaturation, or RSS. RSS can be written using the solute concentration, Q, and its equilibrium solubility, S.

The average relative supersaturation when the reagent is added is inversely related to particle size. A high relative supersaturation ratio favors colloidal precipitates. A low relative supersaturation ratio favors crystalline precipitates with larger particles.

Controlling Precipitate Size in Gravimetry

controlling-precipitate-size-in-gravimetry

complexometric titration: overview

Metal Ion Endpoints in Complexometric Titration

Complexometric titration tracks metal ions by forming a complex with one or more ligands. In this method, the metal ion reacts with the added ligand to produce a metal-ligand complex. The result is used in analytical chemistry to help identify the endpoint of the titration. A visual indicator is often added to the metal solution before the titration begins. It forms a stable metal-indicator complex and gives the solution its color. As the titration nears the equivalence point, excess ligand...

complexometric titration: ligands

EDTA in Complexometric Titration

Complexometric titration uses ligands to bind metal ions. In these reactions, monodentate and polydentate ligands can act as complexing agents. A ligand is a molecule or ion that attaches to a metal ion and forms a complex. Monodentate and bidentate ligands often form complexes in two or more intermediate steps. That makes them less useful for complexometric titration. Polydentate ligands can bind a metal ion in a single step. This helps produce a sharper end point. For this reason,...

properties of organometallic compounds

Carbon-Metal Bond Reactivity in Organometallics

Organometallic compounds contain a carbon-metal bond. The carbon is part of an organyl group, such as alkyl, aryl, allyl, or benzyl. The metal may come from Group I or Group II of the periodic table, a transition metal, or a semimetal. The carbon-metal bond is polar. Carbon is more electronegative than the metal, so the shared electrons are pulled toward carbon. This gives the carbon atom electron-rich, carbanion-like character. That carbanionic character makes organometallic compounds strong...

edta: chemistry and properties

EDTA in Metal Ion Titrations

EDTA is a key chelating agent used in metal ion titrations. It belongs to a group called polydentate ligands, which make more stable complexes with metal ions than mono- or bidentate ligands because of the chelate effect. Polydentate ligands are often preferred in complexometric titrations because they can form 1:1 complexes in a single-step process. Other examples include crown ethers and cryptands. Amino carboxylic acid derivatives are also commonly used as complexing agents. EDTA is one of...

edta: conditional formation constant

EDTA Binding and pH-Dependent Stability

EDTA binding and pH-dependent stability depend on how the molecule changes with acidity. EDTA has six binding sites: four carboxyl groups and two amino groups. Its fully protonated form is written as H6Y2+. At different pH levels, it can also appear as H5Y+, H4Y, H3Y−, H2Y2−, and HY3−. In very basic solutions above pH 10.17, the fully deprotonated form, Y4−, is the main species. This form binds metal ions readily in a 1:1 ratio. For the equilibrium between a metal ion and Y4−, the formation...

edta: auxiliary complexing reagents

EDTA Titration: Preventing Metal Precipitation

EDTA titrations are often done in highly basic conditions. In this setting, the fully deprotonated form of EDTA, Y4−, is the active species that binds free metal ions in solution. Basic conditions can also cause some metal ions to precipitate as hydrous oxides. These solids may be hydroxides, oxides, or oxyhydroxides. When that happens, the amount of free metal ion in solution drops. Auxiliary complexing agents help solve this problem. Ammonia, tartrate, citrate, and triethanolamine can bind...

edta: direct, back-, and displacement titration

edta-direct-back-and-displacement-titration

EDTA Titrations for Metal Ion Analysis

EDTA titrations are used to analyze metal ions through direct titration, back-titration, and replacement titration. Each method helps measure metals in solution when the reaction conditions are different. In all three cases, EDTA binds metal ions to form stable complexes. In direct titration, the metal ion solution is buffered to the right pH and then titrated with standard EDTA until the endpoint is reached. The best pH gives a large conditional formation constant for the metal-EDTA complex...

edta: indirect and alkalimetric titration

EDTA Titration for Anions and Metal Ions

EDTA titration can be used to measure anions and metal ions through indirect and alkalimetric methods. These approaches extend the use of EDTA beyond a simple direct titration. In indirect titration, the anion is first turned into an insoluble salt with excess metal ions. The filtrate, which contains the extra metal ions, is then titrated directly with standard EDTA until the endpoint is reached. Another indirect approach removes the metal ion first and then uses standard EDTA in a...

complexometric edta titration curves

EDTA Titration Curves and Metal Ion Change

EDTA titration curves show how the free metal ion concentration changes as EDTA is added. The curve tracks the p function, or the concentration of free metal ions, against the volume of EDTA added. It helps students see how metal ions shift during a complexometric titration. The curve has three main regions. Before the equivalence point, excess free metal ions are present. At the equivalence point, the metal ions and EDTA are present in equal concentrations. After the equivalence point, excess...

effects of edta on end-point detection methods

effects-of-edta-on-end-point-detection-methods

EDTA Titration Endpoint Detection Methods

EDTA titration endpoint detection can be done with visual, spectroscopic, or potentiometric methods. Each method helps show when the metal ion has been fully complexed by EDTA. In the visual method, metal-ion indicators, also called metallochromic dyes, are added to the solution. These indicators have different colors in their free and complex forms. They bind metal ions, but their complexes are weaker than the metal-EDTA complex. As EDTA reaches the endpoint, it displaces the indicator and...

masking and demasking agents

EDTA Titration Metal Ion Masking

EDTA titration can use masking agents to keep one metal ion from reacting right away. A masking agent forms a stable complex with a chosen ion, while other metal ions can still react with EDTA. This makes it possible to analyze ions one after another in a mixture. Several masking agents are used in this type of analysis. Examples include cyanide, fluoride, triethanolamine, thiourea, and 2,3-bis(sulfanyl)propan-1-ol, which was formerly called 2,3-dimercapto-1-propanol. The best choice depends...

precipitation titration: overview

Precipitation Titration Curves and Endpoints

Precipitation titration uses a titrant and an analyte to form an insoluble precipitate. In many cases, silver nitrate is the most common precipitating reagent. Titrations that use Ag+ are called argentometric titrations. The endpoint is usually detected with visual indicators. A precipitation titration curve shows how the concentration of the titrant or analyte changes as titrant is added. These curves are plotted with the volume of analyte on the x-axis and the p function of the analyte or...

precipitation titration curve: analysis

Interpreting Precipitation Titration Curves

A precipitation titration curve shows how the concentration of one reactant changes as titrant is added. In chloride titration with silver nitrate, the curve is used to track silver ion concentration as the reaction proceeds. The curve has three regions: before the equivalence point, at the equivalence point, and after the equivalence point. Before equivalence, the sparingly soluble silver chloride precipitate redissolves only a little, so the silver ion concentration stays low. At the...

precipitation titration: endpoint detection methods

precipitation-titration-endpoint-detection-methods

Visual Endpoints in Precipitation Titrations

Precipitation titrations can use visible color changes to show when the endpoint is reached. In argentometric titrations, the Mohr, Volhard, and Fajans methods each give a different visual signal for the end of the reaction. The Mohr method uses a soluble chromate indicator. The analyte solution starts yellow, and then the first excess of silver ions forms a red silver chromate precipitate. That red color marks the endpoint, and the solution pH should be kept near 8 by adding solid CaCO3. The...

gravimetry: overview

Gravimetric Analysis Methods

Gravimetric analysis is a quantitative method in which an analyte is isolated and then weighed. In some cases, the analyte is weighed directly. In other cases, it is converted into a substance with a known composition before weighing. This method is grouped by how the analyte is separated. Precipitation gravimetry turns the analyte into a precipitate, which is a solid that forms from a solution, and then measures its mass. A common example is estimating silver content by forming and weighing...

gravimetry: inorganic and organic precipitating agents

gravimetry-inorganic-and-organic-precipitating-agents

Gravimetry: Choosing Selective Precipitants

Gravimetry uses selective precipitants to form a pure solid that can be filtered and weighed. The choice of precipitant matters because the solid must be easy to collect and suitable for measurement. Common inorganic precipitants can be used to determine several cations and anions. In some cases, the same precipitate helps identify both ions. A familiar example is barium chromate, which forms from barium and chromate ions. Some precipitates, including hydroxides, oxalates, and metal ammonium...

precipitation gravimetry

Nickel Weighing by Precipitation Gravimetry

Precipitation gravimetry can be used to measure nickel by turning it into a solid that can be filtered and weighed. In this method, the analyte is converted into a sparingly soluble precipitate. The solid is then separated from the mixture and used to find the amount of nickel present. A good precipitate should be pure, insoluble, of known composition, and easy to filter. For nickel analysis, ethanolic dimethylglyoxime is added to a hot nickel salt solution. Dilute ammonia is then added...

Precipitation gravimetry uses a precipitating agent that reacts specifically or selectively with the analyte. A specific reagent reacts with the analyte alone. A selective reagent reacts with a limited number of chemical species. The precipitate should be a pure substance with a known composition, or it should be easy to convert into one by drying or ignition. It should also be insoluble and easy to filter. Filterability usually improves as particle size increases. Colloidal suspensions...

precipitation processes

Growing Purer Precipitates

Growing purer precipitates depends on controlling how particles form in gravimetric analysis. The best conditions use a low concentration of the precipitating reagent and constant stirring. This keeps relative supersaturation low and helps large crystals grow. Homogeneous precipitation uses a different approach. The precipitant is slowly made inside the solution by a chemical reaction, so there is no local excess of reagent. A common example is urea, which breaks down slowly and releases...

colloidal precipitates

Colloidal Precipitate Stability

Colloidal precipitates can form when a very insoluble solid is produced under high relative supersaturation. Their particles have a large surface-to-mass ratio, so surface adsorption becomes important. Silver chloride is a common example of this behavior. In colloidal silver chloride, silver ions adsorb on the particle surface and form a primary layer. This layer attracts oppositely charged ions, such as nitrate ions, which build a diffuse secondary layer. Together, these layers make an...

types of coprecipitation

How Coprecipitation Contaminates Precipitates

Coprecipitation is the contamination of a precipitate by substances that should stay dissolved. It can happen through several different processes. In colloidal precipitates, one common route is surface adsorption, where ions stick to the outside of the particles. A classic example is barium sulfate. It can build a primary layer of adsorbed barium ions and a secondary layer of nitrate counterions. This makes the precipitate contaminated with barium nitrate. Coprecipitation can also happen by...

washing, drying, and ignition of precipitates

washing-drying-and-ignition-of-precipitates

Purifying and Heating Precipitates for Weighing

After filtration, a precipitate is washed to remove coprecipitated impurities and any leftover mother liquor. A mother liquor is the liquid that remains after the solid forms. Washing helps make the final solid cleaner before it is measured. The wash solution depends on the type of precipitate. Colloidal precipitates, such as silver chloride, are washed with an electrolyte like dilute nitric acid to prevent peptization, which is the re-dispersion of the solid. Slightly soluble precipitates are...

key terms and concepts

Learn how precipitation gravimetry uses selective reagents, particle size, and relative supersaturation to form filterable crystalline or colloidal precipitates.

Controlling Precipitate Size in Gravimetry | JoVE K12

analytical chemistry

JoVE Core Analytical Chemistry simplifies complex chemical principles by breaking them down into clear, engaging animations, making topics from SI Units to NMR spectroscopy more accessible and straightforward. Additionally, the scientist-in-action videos highlight the application of these concepts in real-world research conducted in laboratories globally.

Controlling Precipitate Size in Gravimetry

Description

Transcript

Tags