Name: centrifugal pump flow rate calculation
Uploaded: 2025-02-13T15:43:22.000Z
Duration: 1 min 4 s
Channel: JoVE

If the flow rate of a centrifugal pump that applies a pressure of 7500 joules per second to lift water from a reservoir at a lower level to a reservoir at an upper level has to be calculated, the energy equation can be used.
The level difference between the reservoirs is 10 meters, and the head loss is 5 meters.
As the surfaces of both reservoirs are open to the atmosphere, the pressure and velocity in both the inlet and the outlet are zero, further simplifying the energy equation.
Here, the head of the pump is obtained by the quotient of the net shaft power input and the product of the unit weight of the water and the flow rate.
If the head of the pump is substituted for the simplified energy equation, the pump&#39;s flow rate can be obtained.
Further, substituting the values provided in the expression for the flow rate gives the final value indicating the rate at which the water is pumped.

application of the energy equation

The application of the energy equation to centrifugal pumps is a fundamental principle in fluid dynamics and engineering. In this scenario, the energy equation is used to calculate the flow rate of a centrifugal pump responsible for transferring water between two reservoirs at different elevations. The pump applies an energy input of 7500 joules per second, and the vertical difference between the lower and upper reservoirs is 10 meters. Additionally, the head loss due to friction and other resistances is 5 meters. These parameters are essential to solving the flow rate using the energy equation.
Because both reservoirs are open to the atmosphere, the pressure at both the inlet and outlet of the pump is equal to atmospheric pressure. This allows the pressure terms in the energy equation to cancel out. Furthermore, since the velocities at the inlet and outlet are negligible, the velocity terms in the equation are also eliminated. The energy equation for this specific case only depends on the gravitational head and the pump head.
The head generated by the pump is determined by dividing the net shaft power input by the product of the flow rate and the specific weight of water. Substituting this head into the energy equation and solving for the flow rate of the pump can be determined.

Application of the Energy Equation

If the flow rate of a centrifugal pump that applies a pressure of 7500 joules per second to lift water from a reservoir at a lower level to a reservoir at ...

Education

JoVE Core

Civil Engineering

Unit 1

Finite Control Volume Analysis

KEY TERMS AND CONCEPTS

centrifugal pump flow rate calculation

Centrifugal pump flow rate can be calculated with the energy equation. In this problem, water moves between two reservoirs at different elevations, and the pump provides the energy needed for the transfer. The pump input is 7500 joules per second, the elevation difference is 10 meters, and the head loss from friction and other resistances is 5 meters.

Both reservoirs are open to the atmosphere, so the pressure at the inlet and outlet is the same. That means the pressure terms in the energy equation cancel. The flow at the inlet and outlet is also negligible, so the velocity terms drop out as well.

With pressure and velocity terms removed, the equation depends on the gravitational head and the pump head. The pump head is found by dividing the net shaft power input by the product of the flow rate and the specific weight of water. Substituting that head into the energy equation makes it possible to solve for the pump flow rate.

Centrifugal Pump Flow Rate Calculation

conservation of mass in finite cotrol volume

conservation-of-mass-in-finite-cotrol-volume

Continuity Equation for a Fixed Control Volume

The continuity equation describes conservation of mass for a fixed control volume. In fluid mechanics, a system is a collection of the same contents over time, and its mass stays constant. That idea is the starting point for deriving the equation. To analyze flow, a fixed, non-deforming control volume is chosen so it matches the system at one instant. The Reynolds transport theorem then links the system to the control volume. It shows that the rate of change of system mass has two parts: mass...

conservation of mass in fixed, nondeforming control volume

conservation-of-mass-in-fixed-nondeforming-control-volume

Continuity and Velocity in Pipe Flow

Conservation of mass explains how fluid moves through a fixed control volume such as a pipe or duct. In a fixed, nondeforming control volume, the total mass stays constant unless mass enters or leaves through the control surfaces. For steady, incompressible flow, the mass entering the system equals the mass leaving it. A sewer pipe is a useful example of this idea. It can be treated as a fixed control volume with inlet and outlet control surfaces around the flow region. Because the fluid is...

conservation of mass in moving, nondeforming control volume

conservation-of-mass-in-moving-nondeforming-control-volume

Stormwater Detention Basin Mass Balance

Stormwater detention basins use mass balance to manage runoff during heavy rainfall. These basins are especially important in urban areas, where impervious surfaces can increase flooding risk. Engineers use the conservation of mass to track how water enters, is stored in, and leaves the basin. In a detention basin, the control volume is the water inside the basin. Its boundaries are the basin walls, the inflow pipes, and the outflow structures. During a rain event, water comes in through the...

linear momentum in control volume

Momentum Balance for Fluid Control Volumes

Linear momentum balance for a fluid control volume links Newton’s second law to moving fluid. The law says that the rate of change of linear momentum equals the sum of the external forces acting on the system. In a fluid system, this idea helps explain how motion and force are related. A control volume can match the fluid system at a specific moment. When that happens, the forces on the control volume and the system are the same. Reynolds transport theorem explains this connection by splitting...

application of the linear momentum equation

application-of-the-linear-momentum-equation

Forces in a 180° Pipe Bend

Forces in a 180-degree pipe bend can be found by applying the linear momentum equation to flowing water. The pipe has a constant cross-sectional area of 0.01 square meters, and the water moves at 15 meters per second. The pressure at the inlet is 0.2 megapascals, and the pressure at the outlet is 0.16 megapascals. The goal is to find the force components in the x and y directions that hold the bend in place. In this case, the flow is only in the y direction at both the entrance and the exit.

moment-of-momentum equation

Wind Turbine Torque and Angular Momentum

The moment-of-momentum equation helps explain how wind turbine blades create torque. Torque is the turning effect of a force around an axis. In rotating systems, this equation links the motion of the wind with the force acting on it. The equation begins with Newton's second law for a fluid particle. That law says the rate of change of linear momentum equals the external force on the particle. To find torque, the position of the particle relative to the rotation axis is combined with that force.

conservation of energy in control volume

Turbine Work from Energy Changes

A turbine can turn fluid energy into shaft work when flow passes through a control volume. The fluid enters the turbine at one point and leaves at another. Under steady-flow conditions, there is no energy buildup inside the control volume, so the stored energy does not change with time. This steady-flow setup makes the energy equation simpler. The turbine is treated as doing mechanical work, and heat transfer is taken as negligible, so Q̇ is approximately zero. The flow at the inlet and outlet...

Centrifugal pump flow rate can be calculated with the energy equation. In this problem, water moves between two reservoirs at different elevations, and the pump provides the energy needed for the transfer. The pump input is 7500 joules per second, the elevation difference is 10 meters, and the head loss from friction and other resistances is 5 meters. Both reservoirs are open to the atmosphere, so the pressure at the inlet and outlet is the same. That means the pressure terms in the energy...

design example: forces in sluice gate

Sluice Gate Water Pressure and Reaction Force

Sluice gates control water flow in channels, reservoirs, and irrigation systems. They work as vertical barriers with an opening that can be raised or lowered. Changing the opening height changes the water velocity and pressure below the gate. The forces on a sluice gate depend on the water depths upstream and downstream, written as z1 and z2. When the gate is closed, the upstream water depth is greater. That creates a strong pressure difference across the gate and a net force toward the...

key terms and concepts

Use the energy equation to find the flow rate of a centrifugal pump lifting water between reservoirs. Includes elevation change, head loss, and pump head.

Centrifugal Pump Flow Rate Calculation | JoVE K12

JoVE Core Civil Engineering offers a foundational exploration of essential construction materials such as bricks, stones, steel, wood, and concrete, along with fluid mechanics topics like flow over immersed bodies, open channel flow, and dimensional modeling. It also covers key surveying concepts, including leveling, traverse adjustments, curve design, topographic mapping, and geospatial technologies (GPS & GIS). Science-in-action videos showcase laboratory research on materials, fluids, and surveying practices in real-world engineering systems.

Centrifugal Pump Flow Rate Calculation

Description

Transcript

Tags