Generation and Coherent Control of Pulsed Quantum Frequency Combs

Summary

A protocol is presented for the practical generation and coherent manipulation of high-dimensional frequency-bin entangled photon states using integrated micro-cavities and standard telecommunications components, respectively.

Abstract

We present a method for the generation and coherent manipulation of pulsed quantum frequency combs. Until now, methods of preparing high-dimensional states on-chip in a practical way have remained elusive due to the increasing complexity of the quantum circuitry needed to prepare and process such states. Here, we outline how high-dimensional, frequency-bin entangled, two-photon states can be generated at a stable, high generation rate by using a nested-cavity, actively mode-locked excitation of a nonlinear micro-cavity. This technique is used to produce pulsed quantum frequency combs. Moreover, we present how the quantum states can be coherently manipulated using standard telecommunications components such as programmable filters and electro-optic modulators. In particular, we show in detail how to accomplish state characterization measurements such as density matrix reconstruction, coincidence detection, and single photon spectrum determination. The presented methods form an accessible, reconfigurable, and scalable foundation for complex high-dimensional state preparation and manipulation protocols in the frequency domain.

Introduction

The control of quantum phenomena opens the possibility for new applications in fields as diverse as secure quantum communications¹, powerful quantum information processing², and quantum sensing³. While a variety of physical platforms are actively being researched for the realizations of quantum technologies⁴, optical quantum states are important candidates as they can exhibit long coherence times and stability from external noise, excellent transmission properties, as well as compatibility with existing telecommunications and silicon chip (CMOS) technologies.

Towards fully realizing the potential of photons for quantum technologies, state complexity and information content can be increased through the use of multiple entangled parties and/or high-dimensionality. However, the on-chip generation of such optical states lacks practicality as setups are complicated, not perfectly scalable, and/or use highly-specialized components. Specifically, high-dimensional path-entanglement requires coherently-excited identical sources and elaborate circuits of beam-splitters⁵ (where is the state dimensionality), while time-entanglement needs complex multi-arm interferometers⁶. Remarkably, the frequency-domain is well-suited for the scalable generation and control of complex states, as shown by its recent exploitation in quantum frequency combs (QFC)^7,8 using a combination of integrated optics and telecommunication infrastructures⁹, and provides a promising framework for future quantum information technologies.

On-chip QFCs are generated using nonlinear optical effects in integrated micro-cavities. Using such a nonlinear micro-resonator, two entangled photons (noted as signal and idler) are produced by spontaneous four-wave mixing, via the annihilation of two excitation photons - with the resultant pair generated in a superposition of the cavity's evenly-spaced resonant frequency modes (Figure 1). If there is coherence between the individual frequency modes, a frequency-bin entangled state is formed¹⁰, which is often referred to as a mode-locked two photon state¹¹. This state wave-function can be described by,

Here, and are the single-frequency-mode idler and signal components, respectively, and is the probability amplitude for the -th signal-idler mode pair.

Previous demonstrations of on-chip QFCs highlight their versatility as viable quantum information platforms, and include combs of correlated photons¹², cross-polarized photons¹³, entangled photons^14,15,16, multi-photon states¹⁵, and frequency-bin entangled states^9,17. Here, we provide a detailed overview of the QFC platform and a protocol for high-dimensional frequency-bin entangled optical state generation and control.

Future quantum applications, especially those to be interfaced with high-speed electronics (for timely information processing), demand the high-rate generation of high-purity photon states in a compact and stable setup. We use an actively mode-locked, nested cavity scheme to produce QFCs within the telecommunications S, C, and L frequency bands. A micro-ring is incorporated into a larger pulsed laser cavity, with optical gain (provided by an erbium-doped fiber amplifier, EDFA) filtered to match the micro-ring excitation bandwidth¹⁸. Mode-locking is actively realized via electro-optic modulation of the cavity losses¹⁹. An isolator ensures that pulse propagation follows a single direction. The resulting pulse train has very low root mean square (RMS) noise and exhibits tunable repetition rates and pulse powers. A high isolation notch filter separates the emitted QFC photons from the excitation field. These single photons are then guided through fibers for control and detection.

Our scheme is a step towards a high generation-rate, small-footprint QFC source, as all components used can potentially be integrated onto a photonic chip. Additionally, pulsed excitation is particularly well-suited for quantum applications. First, looking at a pair of micro-cavity resonances symmetric to the excitation, it generates two-photon states where each photon is characterized by a single-frequency mode– central for linear optical quantum computing²⁰. As well, multi-photon states can be generated by moving to higher power excitation regimes and selecting multiple signal-idler pairs¹⁵. Second, as photons are emitted in known time windows corresponding to the pulsed excitation, post-processing and gating can be implemented to improve state detection. Perhaps most significantly, our scheme supports high generation rates of photon states using harmonic mode-locking without reducing the coincidence-to-accidental ratio (CAR) – which could pave the way for high-speed, multi-channel quantum information technologies.

To demonstrate the impact and feasibility of the frequency-domain, control of QFC states must be accomplished in targeted ways, ensuring highly efficient transformations and state coherence. To satisfy such requirements, we use cascaded programmable filters and phase modulators – established components in the telecommunications industry. Programmable filters can be used to impose an arbitrary spectral amplitude and phase mask on the single photons, with a resolution sufficient to address each frequency mode individually; and electro-optic phase modulators driven by radio-frequency (RF) signal generators facilitate the mixing of frequency components²¹.

The most important aspect of this control scheme is that it operates on all quantum modes of the photons simultaneously in a single spatial mode, using single control elements. Increasing the quantum state dimensionality will not lead to an increase in the setup complexity, in contrast to path- or time-bin entanglement schemes. As well, all components are externally reconfigurable (meaning the operations can be altered without amending the setup) and use existing telecommunications infrastructure. Thus, existing and upcoming developments in the field of ultrafast optical processing can be directly transferred to the scalable control of quantum states in the future.

In summary, the exploitation of the frequency-domain by QFCs supports the high-rate generation of complex quantum states and their control, and, is thus well-suited for the harnessing of complex states towards practical and scalable quantum technologies.

Protocol

1. Generation of the High-dimensional Frequency-bin Entangled States via Pulsed Excitation

1. Following the scheme outlined in Figure 2 (Generation stage), connect each component using polarization-maintaining optical fibers (for improved environmental stability).
2. Connect a power supply to the electro-optic amplitude modulator and apply a DC voltage offset, tuning the offset value until the optical power transmitted through it is approximately halved (measured using an optical power meter), e.g., such that a peak transmission value of 2 mW is halved to 1 mW.
3. Measure the approximate external cavity length. Calculate the external cavity mode spacing using the relationship,
   
   where is the external cavity mode spacing, c is the speed of light in vacuum, is the effective index of the cavity medium, and L is the external cavity length. For example, for a 20 m cavity comprised of fiber with an effective refractive index of 1.46, the approximate cavity mode spacing would be 10.2 MHz.
4. Turn on the EDFA to initiate lasing.
5. Insert the fast photodiode into the setup at either the cavity coupler or other ring ports. Connect the photodiode signal to an oscilloscope to observe the excitation field's intensity in the time-domain.
6. Set the oscilloscope time resolution to <100 ps (through the horizontal scale knob) in order to resolve the ns-scale pulses. At this step, without the modulator activated, the output on the oscilloscope will show unstable pulse operation with a low quality, high noise pulse train.
7. Connect a function generator to the electro-optic amplitude modulator. Set the frequency of the function generator output to the (approximate) external cavity mode spacing found above (or a harmonic of it). This signal performs the mode-locking. Choose either a pulse (rectangular) waveform or sine wave for amplitude modulation. Turn on the function generator.
8. Tune the RF function generator frequency and DC offset to optimize and stabilize the pulse train shape on the oscilloscope. If a pulsed driving signal is used, optimize its duty cycle.
9. Manually adjust the EDFA gain to reduce (or increase) pulse intensity to the regime where the properties of the generated photons are as desired by the user (CAR is a useful metric here - see below for details on its measurement). For this, compare the respective coincidence histograms generated by the visual interface that comes with the timing electronics.
10. Feed the timing electronics sync channel with the pulse train signal (detected by the photodiode) or the RF mode-locking signal to synchronize the single photon detectors with the photon pair generation.
11. To increase the generation rate of the QFCs, drive the mode-locking modulator at higher harmonics of the external cavity frequency spacing while simultaneously augmenting the EDFA gain to ensure the same power per pulse — this maintains the photon pair CAR while boosting the pair production rate (Figure 3). For this, increase the function generator output frequency and EDFA gain respectively.

2. Control of the High-dimensional Frequency-bin Entangled States

1. Following the scheme outlined in Figure 2 (Control stage), connect all components using polarization-maintaining fibers. Beginning from the notch filter in the generation scheme, connect in series the first programmable filter, phase modulator, and second programmable filter. Finally connect the single photon detectors for measurement purposes.
2. Programmable filter operation
   NOTE: Depending on the specific application/measurement being performed, the control parameters of the QFC will vary and the phase and amplitude masks applied to the frequency modes must be determined accordingly. The amplitude mask can be used to attenuate or block certain frequency modes and the phase mask can impart an arbitrary phase shift on each mode.
   1. Determine the necessary masks for the desired application/measurement.
   2. Via the programmable filter visual interface²², set the amplitude of the desired frequency mode channels and attenuate all others.
   3. Similarly, apply the phase mask (the phase applied to the undesired channels is unimportant, as they are fully attenuated). Control the programmable filter with a visual interface where the desired frequencies are selected.
3. Phase modulation operation
   1. Using phase modulation, driven by a periodic signal, split each spectral component into side-bands evenly spaced by the frequency of the signal generator that is driving the phase modulator. Use this to mix several different quantum frequency modes, analogous with spatial beam-splitters in path-entanglement schemes. In the quantum regime, electro-optic phase modulation is considered a quantum scattering operation²³.
   2. Determine the target frequency modes (dependent on and the measurement/processing being performed) and calculate the voltage pattern (frequency and amplitude for a sine wave generator) to optimize the desired values (see below for some details on this).
   3. Connect the signal generator to the RF amplifier using low-loss cables (such as SMC cables). Connect the RF amplifier output to the phase modulator, also using adequate RF cables. Once all RF ends are connected and properly terminated, bias the RF amplifier.
   4. Ensure that the RF amplifier has sufficient output power to drive the electro-optic phase modulator with sufficient voltage to meet the desired mixing conditions — these are on the order of several (the half-wave voltage of the phase modulator). Also, ensure that the RF cables and connectors are adequate for the bandwidth and frequency range of the driving signal.
   5. Set the RF signal generator (which is driving the phase modulator) at a frequency which will overlap the desired modes with the created side-bands (e.g., 33 GHz).
   6. Turn on the signal generator to mix the frequency modes.
   7. To verify that the correct modulation is applied, send a continuous-wave laser through the phase modulator and check that the output spectrum corresponds to the intended modulation using an optical spectrum analyzer (the modulation parameters can be further optimized, see notes).
      NOTE: Optimizing the mixing of frequency modes (determining the optimal function frequency and amplitude) is highly dependent on the desired mixing scheme, experiment being performed, and state dimensionality . If possible, the mixing schemes should mix modes close to the initial frequency mode (at low-integer sidebands) to increase the mixing efficiency. For example, if , the mixing is recommended to occur halfway between the two frequency modes (thus, the phase modulation should be driven at a frequency which has an integer multiple equal to half the quantum mode frequency spacing, or free spectral range (FSR)). However, for , mixing is recommended to occur in the center frequency mode (phase modulation should be driven at a frequency with an integer multiple equal to the FSR). For example, with and micro-cavity GHz, the phase modulation driving signal is set to 33.33 GHz such that the sideband overlaps with the neighboring frequency modes - while also leaving sufficient intensity in the center frequency mode. This results in the overlapping of sidebands neighboring modes , and at the center frequency mode . Figure 4a visualizes an example of the modulation process and the sideband coefficients. Each frequency mode undergoes the same phase modulation and creates the same sideband distribution, but centered about the original frequency mode (Figure 4a). For a single frequency mode, the sideband amplitudes are calculated as the coefficients of a Fourier series²⁴,
      
      where is the amplitude transferred to the -th sideband, is the frequency that the phase modulator is driven at, is the phase modulation pattern (periodic with frequency ), and is the argument of the periodic modulation function (). For a sinusoidal driving signal, , the side-band amplitudes are described by the Jacobi-Anger expansion,
      
      
      where is the -th order Bessel function of the first kind evaluated at and is the maximum phase shift (where is the voltage amplitude of the single-tone driving signal).

3. Processing of the High-dimensional Frequency-bin Entangled States

1. Single photon spectrum
   1. Insert a single photon detector following the filtering of the excitation field from the QFC, at the output of a programmable filter.
   2. Via the programmable filter computer software, sweep over the full programmable filter bandwidth using a narrow bandpass filter amplitude mask, measuring photon count rates as a function of frequency. For example, if a visual interface/control script in MATLAB is used (that is interfaced with the programmable filter control and timing electronics), enter the desired filter bandwidth values and step number and click "Run". Ensure sufficient integration time to get proper photon counts.
   3. To reconstruct the spectrum from this data, plot (for example, using a Matlab script) the photon count rates against the corresponding wavelength (bandpass filter center) where they were acquired.
2. Coincidence measurement
   1. To perform a coincidence measurement, split and route the signal and idler photons to separate single photon detectors. If the programmable filter has multiple ports, use it to perform the separation. Otherwise, insert a dense-wavelength division multiplexer (DWDM) prior to the single photon detectors and use this to route the photons.
   2. Select a signal and idler pair (for example, the second resonance lines with respect to the excitation frequency, signal-2 and idler-2) using the programmable filter (via the supplied software interface) and route them to two separate single photon detectors. For example, for the WaveManager software, click the Flexgrid sub-menu, click "Add" and enter the wavelength and output port for the chosen channel²².
   3. Record the arrival time of the signal and idler photons using the time-to-digital converter. From these measurements, compute the time delay between the two photons. Plot a histogram (for example, using a Matlab script) of coincidence counts for a time-delay between signal and idler — this provides a coincidence measurement.
      NOTE: The CAR metric compares the number of true coincidence counts from the generated photon pairs with the accidental coincidence counts arising from multi-photon processes and dark counts.
   4. From the above-computed measurement, record the number of counts in the center peak (coincidences stemming from photons produced in the same pulse, centered around the zero delay, ) — which is the coincidence value.
   5. Record the average number of counts in each side-peak (coincidences of photons produced in different pulses, where is a multiple of the pulse train period, i.e., the inverse of the pulse repetition rate), which is the accidental value.
      NOTE: The CAR is simply the ratio of these two values (coincidence value/accidental value).
3. Density matrix reconstruction
   NOTE: The process for density matrix reconstruction depends on several parameters of the quantum state: the dimensionality of the photons, the number of photons, and which modes are being measured. The number of raw measurements required is equal to , where is the dimensionality and is the number of photons. So, for example, a two-photon pair with a dimensionality of will require 81 measurements. This protocol will outline the general process for density matrix reconstruction, with examples for a pair of frequency mode photons.
   1. Determine a set of basis vectors for the desired state and a set of projection vectors (see below for details on how to appropriately choose these).
   2. With a coincidence measurement, use either a programmable filter or a DWDM route signal and idler photons to separate single photon detectors.
   3. Via the programmable filter software control, select the desired frequency modes and attenuate all others. Set the phase mask values to realize each projection wavevector individually and record a coincidence measurement. It is important to allow the same integration time between different projection coincidence counts.
   4. Using a custom computer script, compute the density matrix of the photons using the raw coincidence count measurements of each projection wavevector (see below for relevant computational details).
      NOTE: When determining basis vectors for the density matrix measurement, they must span the state space. For the example case, the basis vectors are
      
      For a state , the density matrix describes the quantum state by,
      
      The density matrix for any real physical system must be a positive-definite, Hermitian matrix - but due to noise, this may not always be the case. In the example case with the chosen basis, the wavevector for the ideal maximally frequency-entangled state can be represented as
      
      and thus, the theoretical density matrix would be:
      
      Projection measurements are taken on a series of projection wavevectors, . Coincidence counts for each projection are given as,
      
      where is a constant (see below for definition).
   5. Choose an orthogonal set of , normalized matrices, , such that
      
      where is the trace, is the dimension, is the number of photons, and is the Kronecker delta function. These matrices can be constructed using the special unitary SU() generators (of which there are ), along with the identity matrix, through all possible tensor product combinations²⁵. See below for the orthogonal matrices of the example case.
   6. Reconstruct the density matrix, , via the following relationships,
      
      
      
      
      where is the photon counts for the -th projection vector, are the projection vectors (see next step), where and are calculated according to the equation definition.
      NOTE: Projection wavevectors for the example case are,
      
      
      
      
      
      
      
      
      Experimentally, these wavevectors are realized by imparting the appropriate phase shift on each mode via the programmable filter. Refer to previous publication²⁵ for discussion on projection vectors. The orthogonal set of matrices, for the example case are chosen first using the SU(3) generators along with the identity matrix,
      
      
      
      
      
      
      
      
      
      and are computed as,
      
   7. For a more in-depth discussion of high-dimensional state reconstruction, refer to reference 25 ²⁵.

Results

The outlined scheme for the generation and control of high-dimensional frequency-bin states (based on the excitation of nonlinear micro-cavities, Figure 1) is shown in Figure 2. This setup uses standard telecommunications components and is highly flexible in the photon production rate and the processing operations applied. Figure 3 shows the characterization of the generation scheme through the coinc...

Discussion

The optical frequency-domain, via QFCs, is advantageous in quantum applications for a host of reasons. Operations are global, acting on all states simultaneously, which results in a design that does not scale in size or complexity as the state dimensionality increases. This is enhanced as the components can be reconfigured on-the-fly without changing the setup and are capable of being integrated on-chip by exploiting existing and/or developing semiconductor and telecommunications infrastructures. The generation technique...

Materials

List of materials used in this article

Name	Company	Catalog Number	Comments
Superconducting Nanowire Single-Photon Detector System	Quantum Opus	Opus One
Electro-optic phase modulator	EO-Space	Low loss model
Programmable filter	Finisar	WaveShaper 4000s
Timing electronics	PicoQuant	HydraHarp 400
Micro-ring resonator			200 GHz FSR micro-ring resonator made from high refractive index glass. See Ref. 24 for platform details.
Erbium-doped fiber amplifier	Keopsys	PEFA-SP-C-PM-27-B202-FA-FA
Electro-optic amplitude modulator	Oclaro	SD40
RF tone source	Rohde & Schwarz	SMP 04
RF tone amplifier	RF-Lambda	RFLUPA27G34GA
Function generator	Tetronix	AFG 3251
Isolator	General Photonics	NISO-S-15-SS-FC/APF
Oscilloscope	Tetronix	TDS5052B
Photodiode	Finisar	XPDV 50 GHz
DWDM	OptiWorks	DWFUQUMD08BN
Power supply	Madell	CA18303D