Isolation of Small Extracellular Vesicles Derived from Mesenchymal Stem Cells from Large-Volume Samples with GMP Compliance for Clinical Trials

Summary

Small extracellular vesicles derived from mesenchymal stem cells (MSC-sEVs) have been underscored as a cell-free treatment modality with minimal adverse effects. This study provides a protocol combining hemodialysis with ultracentrifugation, significantly reducing the time spent on the entire process and ensuring compliance with good manufacturing practice (GMP) standards.

Abstract

Small extracellular vesicles (sEV) derived from mesenchymal stem cells (MSC-sEVs) have been underscored as a cell-free treatment modality with minimal adverse effects. In contrast, traditional extraction methods such as ultracentrifugation and size-exclusion chromatography are limited by their time intensity, cost, and scalability. To overcome these limitations, we propose a method integrating a hemodialyzer and ultracentrifugation. This approach utilizes a hemodialysis device with a 100 kDa molecular weight cut-off (MWCO) membrane, which selectively concentrates sEVs while filtering out a plethora of proteins, thereby enhancing the yield and purity of sEVs. This initial purification step is followed by ultracentrifugation to further refine the sEV preparation. The integration of these two technologies not only significantly reduced the time spent on the entire process but also ensured compliance with good manufacturing practice (GMP) standards. The method here demonstrates high efficiency in isolating sEVs from a large volume of samples, offering a significant advancement over traditional methods. This protocol holds promise for accelerating the translation of EV-based therapies into clinical practice by providing a scalable, cost-effective, and GMP-compliant solution.

Introduction

Small extracellular vesicles derived from mesenchymal stem cells (MSC-sEVs) are heterogeneous vesicles enriched with multiple components such as mRNA, micro-RNA, cytokines, lipids, and metabolites¹. In recent years, many studies have underscored the immense therapeutic potential of MSC-sEVs as a cell-free treatment modality with minimal adverse effects², showing promise in addressing a spectrum of conditions, including aging, tissue degeneration, cancer, and inflammatory disorder^3,4,5,6. Nevertheless, a critical challenge persists in large-scale extraction of sEV, with traditional methods proving to be either laboriously time-intensive or economically unfeasible. Furthermore, ensuring reproducibility is paramount for the clinical application and translation of EV-based therapies⁷. Researchers are in dire need of a purification method that is not only simple and efficient but also compliant with good manufacturing practice (GMP) standards⁸.

The conventional purification methods, including ultracentrifugation, ultrafiltration, size-exclusion chromatography, immunoaffinity, and polymer precipitation, have been extensively applied in previous research⁹. In general, traditional methods for sEV isolation exhibit limitations such as low yield rate, compromised purity, and challenges in meeting stringent aseptic standards. Furthermore, previous research has reported the potential of promising techniques like microfluidic systems^10,11, label-free magnetic isolation¹², and covalent chemistry isolation¹³ for achieving outstanding performance. However, the requirement for specialized equipment makes these advanced techniques challenging for the majority of research teams to adopt. In summary, the efficient method to isolate GMP grade sEVs from a large volume of samples remains a critical obstacle, limiting the progress of numerous teams in both research and clinical applications.

Ultracentrifugation is the most widely adopted method for sEV isolation and is recognized as the gold-standard method^14,15. It is a technique that leverages differences in density and size to isolate sEVs. Isolated sEVs are commonly rinsed with phosphate-buffered saline (PBS) to eliminate residual contaminants. Then, an appropriate volume of PBS is generally used to resuspend the rinsed sEVs and different expected concentrations of sEVs can be harvested by controlling the volume of PBS. Furthermore, it is reported that the purity of plasma sEVs obtained by ultracentrifugation appears to be better than that of plasma sEVs isolated by size exclusion chromatography (SEC), and the sEVs obtained by ultracentrifugation have lower non-vesicular extracellular particles (NVEPs) impurities. This also makes ultracentrifugation the most widely used and difficult to replace in many treatments that require high concentrations of sEVs. However, in addition to quality and purity, efficiency is also a factor that cannot be ignored in large-volume sEV extraction. So far, a single round of ultracentrifugation can support a sample volume of up to approximately 600 mL, which determines that it is difficult to meet the demand for large-scale extraction by just ultracentrifugation¹⁶.

A hemodialysis device consists of a membrane-based module that houses thousands of hollow fibers. Blood circulates through these fibers within an enclosed cylindrical chamber¹⁷. The constituents of the blood can selectively pass through these membranes based on their molecular size and ionic concentration. In the clinic, it is widely used as an artificial kidney to remove waste products and excess fluids from the blood of patients^18,19,20. In other words, the hemodialyzer also has the potential to concentrate large-volume samples, relying on a process similar to tangential flow filtration (TFF). In the recent guideline issued by the International Society for Extracellular Vesicles (ISEV), sEV concentrates are considered suitable for large-volume samples, such as cell culture medium. After decades of development, hemodialyzers have been widely adopted in hospitals, supported by an abundance of mature consumables and a pool of skilled operators, which makes it easier to keep the sample sterile.

This study presents a sEV purification method based on a hemodialyzer and ultracentrifuge compatible with GMPs. Here, we choose dialyzers of 100 kDa molecular weight cut-off (MWCO), which has been demonstrated to effectively capture sEVs and filter out numerous proteins²². Ultracentrifugation also provides a step for further purification. The work demonstrates that the hemodialyzer is equally suitable for the concentration of sEVs. This protocol allows researchers to isolate sEVs from large-volume samples efficiently. We have registered the clinical trial in Chinese Clinical Trial Registry (ChiCTR, NO. ChiCTR2200059018), which is still in progress and has not been completed yet. Although clinical data is not readily available for publication at this moment, a reliable, large-scale, efficient, and compliant method for producing sEVs as reported in this protocol is a prerequisite for conducting pre-clinical and clinical trials.

Protocol

The protocol was approved and conducted in accordance with the Human Research Ethics Committee of the Southwest Hospital.

1. Removing cell debris from the culture medium

NOTE: The procedures below should be operated in a GMP-compliant environment, especially when the samples may be directly exposed to the environment.

1. Given the requirement of microbiota-free, ensure that the filter and rubber tube are autoclaved for effective sterilization. Ensure all other consumables that might encounter the culture medium are sterile and in sealed packaging. Perform the process of removing cell debris in a laminar flow cabinet.
2. Assemble the 0.45 µm and 0.22 µm filtration membrane to the filter apparatus. Connect a peristaltic pump (see Table of Materials) and the filter apparatus with the rubber tube. Position the 0.45 µm membrane above the 0.22 µm membrane; otherwise, it may decrease filtration efficiency (Figure 1). Pay attention to distinguishing between the microfiltration membrane's front and back sides.
3. Start the peristaltic pump for the filtration. Powered by the pump, the mesenchymal stem cell basal medium (MSCBM) with 5% supplement (see Table of Materials) passes through the filter from one end, and the filtered culture medium can be obtained at the other end of the filter, as shown in (Figure 1). Gather the filtered culture medium in a drainage bag with dual channels. Maintain the integrity of the filtration system by optimizing the peristaltic pump speed and replacing the filtration membrane as needed.
4. After filtration is complete, close the inlet valve on the drainage bag and further seal it with parafilm (see Table of Materials). Continue to the next step or temporarily store the filtered cell culture medium at 4 °C.

2. Concentrating the filtered culture medium with a hemodialyzer

NOTE: Refrain from using Dulbecco's Modified Eagle Medium (DMEM) containing phenol red in cell culture, as the blood-leak detector in the hemodialyzer will be activated or shut down the blood-leak detector in the hemodialyzer setting.

1. Prepare the consumables.
   1. Prepare bloodlines, 100 kDa MWCO high-flux polysulfone membranes, blood dialyzer, infusion set, physiological saline solution, infusion bag, iodine solution, and cotton swabs before concentration (see Table of Materials).
2. Power on the system and self-test.
   1. Check the connection of the hemodialyzer power cable and switch on the main power.
   2. Wait for the machine to complete the entire self-diagnostic procedure.
3. Install the bloodlines and dialyzer.
   1. Verify the expiration dates of the disposable bloodlines and the blood dialyzer, ensuring the integrity of their outer packaging and checking for any damage to the lines.
   2. Install the tubing in the same direction as blood flow in the extracorporeal circuit, sequentially closing the branch valves to form a closed-loop circulation.
4. Start the rinse procedure.
   1. Use an infusion set to connect the physiological saline solution (without heparin) from a tube before the pump to the dialysis circuit. Connect the venous collection site to the waste fluid bag.
      NOTE: The physiological saline should not contain heparin or any other anticoagulants.
   2. Connect the dialysate supply/return lines to the dialyzer.
   3. Start the hemodialyzer and set the flow rate to 80-100 mL/min. Expel all the air from the dialysis circuit and the dialyzer to ensure the entire tubing system is filled with fluid.
   4. Adjust the liquid plane in the arterial and venous chambers to approximately 2/3 full. The saline sequentially flows through the arterial line, the dialyzer, the venous line, and the waste fluid bag.
5. Start the ultrafiltration concentration.
   1. After finishing the rinse procedure, hang the drainage bag containing the filtered culture medium on the infusion stand, disinfect the output channel with iodine-soaked cotton swabs, and connect the output channel of the drainage bag to a pre-pump port using an infusion set.
   2. Join the arterial port and the venous port of the bloodlines. Establish an isolated ultrafiltration (ISO-UF, ultrafiltration without dialysate flow) dialysis circuit (Figure 1).
   3. Adjust the ultrafiltration target volume on the dialysis machine to correspond with the total volume of fluid present in the drainage bag. Set the dialysis time of the ultrafiltration to the minimum operational time of the system. After the parameters are set successfully, initiate the ultrafiltration.
      NOTE: Due to the calculation of the hemodialysis system, the dialysis time will not be too short but will be maintained at a more moderate rate.
6. Obtain the concentrated fluid.
   1. After achieving the target dehydration volume, shut the arterial clamp and connect the venous port to a sterile infusion bag.
   2. Open the pre-pump port of the disposable blood lines equipped with an air filter. Activate the blood pump at a speed of approximately 50 mL/min, allowing the fluid within the bloodlines to circulate once again from the arterial line to the venous line. Retract all the concentrated fluid, approximately 158 mL, from the circuit back into the sterile infusion bag.
   3. In the late stage of concentration, collect the wasted fluid from the dialysate return line. Apply subsequent processes identical to those of the concentrated culture medium to the wasted fluid sample to monitor any accidental loss of sEVs that may have occurred during concentration.
   4. Close all valves and remove the infusion bag, dialyzer, and all lines. Turn off the power supply and disinfect the machine by wiping it down.

3. Separating the sEVs with ultracentrifuge

1. Transfer the concentrated culture medium into ultracentrifuge tubes and then balance them.
2. Centrifuge in a clinical-grade ultracentrifuge (see Table of Materials) at 110,000 × g for 70 min, then wash the pellet with sterile saline solution and proceed with a second centrifugation at 110,000 × g for another 70 min.
3. Resuspend the pelleted sEVs in an appropriate amount of sterile saline solution.
4. Transfer the sEVs to a sterile tube for further testing or store them at -80 °C for future use.

4. Characterization of obtained sEVs

1. Nanoparticle tracking analysis (NTA)
   1. Dilute the obtained sEVs (1 µL) with PBS (1 mL) (see Table of Materials). Adjust the number of sEVs visible in the current field of view to be between 50 and 200.
   2. Carefully inject the diluted sample into the sample well, avoiding the introduction of air bubbles.
   3. Perform the measurement when the number of particles in the field of view is as high and stable as possible for all positions. The analysis parameters are as follows: Max Area: 1000, Min Area: 10, Min Brightness: 30, Trace length: 15, Temperature: 25 °C, Sensitivity: 75.
   4. Measure each sample at least three times.
2. Western blotting analysis
   1. Dilute sEVs solution in PBS. Use a Bicinchoninic Acid (BCA) Protein Assay Kit (see Table of Materials) to measure the protein concentration.
   2. Boil the sEVs in the sample buffer at 100 °C for 5 min.
   3. Prepare a 12% sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) gel (see Table of Materials). Assemble the gel electrophoresis apparatus. Load equal amounts of protein of each sample into the SDS-PAGE gel wells. Set the voltage of electrophoresis to 80 V for concentration and 100 V for separation.
   4. Activate the polyvinylidene difluoride (PVDF) membrane (see Table of Materials) with methanol for 1 min, then soak the PVDF membrane in transfer buffer before proceeding with transfer at 100 V for 1 h.
   5. Immerse the PVDF membrane in TBST buffer (20 mM Tris, 150 mM NaCl, and 0.1% Tween 20) containing 5% bovine serum albumin (BSA; see Table of Materials) and then block for 30 min.
   6. Incubate the PVDF membrane with the primary antibody overnight at 4 °C on a shaker. The primary antibodies used are as follows: human anti-CD63 (1:1000 dilution), human anti-CD9 (1:1000 dilution), and human anti-HSP70 (1:1000 dilution) (see Table of Materials).
   7. Next day, wash the PVDF membrane with TBST solution five times for 5 min each and then incubate with HRP-conjugated secondary antibody (1:10000 dilution) (see Table of Materials) at room temperature (RT) for 1 h.
   8. After washing with TBST five times, use a chemiluminescence detection reagent for imaging on a chemiluminescence system.
3. Transmission electron microscopy
   1. Add a 20 µL PBS-diluted sample drop to a wax paper. Then, place a copper grid (see Table of Materials) onto the drop so the sample drop can cover the copper grid and let it stand at RT for 20 min.
   2. Absorb excess liquid with filter paper. Then, fix the samples in a 20 µL solution of 2% paraformaldehyde, 2% glutaraldehyde, and 0.05 M phosphate solution for 2 min.
   3. Rinse the copper grid three times with double-distilled water, then stain with 20 µL of 2% phosphotungstic acid (PTA) for 1 min at RT.
   4. Absorb redundant liquid with filter paper. Dry the grids overnight before being analyzed by transmission electron microscopy (see Table of Materials).
      NOTE: The recommended settings for TEM are as follows: Exposure: 1.0 s, HT Voltage 100.00 kV, Beam Current: 50 µA, Spot Size: 1, Mode: TEM. These settings might change following the manufacturer's instructions (see Table of Materials).

Results

Morphological characterization of sEVs
In the final stage of concentration, the wasted fluid was also collected as described. The concentrated medium and wasted fluid were ultracentrifuged, respectively. We collected the precipitations for transmission electron microscopy (TEM) analysis. As anticipated, a significant number of cup-shaped nanovesicles were observed in the concentrated medium group (Figure 2A,B). However, t...

Discussion

Traditional methods for the isolation of sEVs include differential ultracentrifugation, size exclusion chromatography, and PEG precipitation, each with its own merits and demerits. While amalgamation of these disparate techniques may enhance the yield or purity of sEVs, additional steps often introduce more opportunities for sample contamination. There are integrated systems claiming to extract sEVs in bulk and adhere to GMP standards have emerged on the market²¹. However, their widespread adoptio...

Materials

List of materials used in this article

Name	Company	Catalog Number	Comments
Anti-CD63	SBI System Biosciences	EXOAB-CD63A-1	1:1000 dilution
Anti-CD9	SBI System Biosciences	EXOAB-CD9A-1	1:1000 dilution
Anti-HSP70	SBI System Biosciences	EXOAB-Hsp70A-1	1:1000 dilution
Bicinchoninic Acid Protein Assay Kit	Beyotime	P0012
Bloodlines	Fresenius Medical Care	AP16641
Bovine serum albumin 5%	Solarbio	9048-46-8
Cell culture supplement	Helios	HPCPLCGL05	5% (v/v) in cell culture media
Copper grid	Precise	RGRS GP-SMPG-1
Dialyzer	Helixone	FX8	100 kDa MWCO
Drainage bag	CZRUIDE	YLD-01
Goat Anti-Rabbit HRP	SBI System Biosciences	EXOAB-CD63A-1	1:10000 dilution
Goat Anti-Rabbit HRP	SBI System Biosciences	EXOAB-CD9A-1	1:10000 dilution
Goat Anti-Rabbit HRP	SBI System Biosciences	EXOAB-Hsp70A-1	1:10000 dilution
Mesenchymal Stem Cell Basal Medium (MSCBM)	Dakewe	DKW34-BM20500
Microfiltration membrane	shanghaixingya	WKLM-50-10	0.45 μm and 0.22 μm
Parafilm	Fisher Scientific	1337416
Peristaltic pump	LongerPump	YZ1515x
Phosphate buffer saline	Solarbio	P1022-500ml
Immun-Blot PVDF Membrane	BIO-RAD	1620177
SDS-PAGE Gel Quick Preparation Kit	Beyotime	P0012AC
SDS-PAGE Sample Loading Buffer	Beyotime	P0015A
Super ECL Plus Western Blotting Substrate	BIOGROUND	BG0001
TBST buffer	Solarbio	T1081
Ultracentrifuge tubes 38.5 mL	Beckman	344058
Bio-Rad ChemiDoc MP Imaging System	BIO-RAD
Hemodialyzer	NIKKISO	DBB-27
Nanoparticle Tracking Analysis	ZetaView	PMX120	To measure particle size distribution and particle concentration
Transmission Electron Microscopy	JEOL	JEM-1400PLUS	Recommended settings?Exposure: 1.0 s, HT Voltafe 100.00 kV, Beam Curr: 50 μA, Spot Size: 1, Mode: TEM.
Ultracentrifuge	BECKMAN COULTER	OPTIMA XPN-100	SW 28Ti SwingingBucket Rotor