Name: sizing a transmission shaft by torque
Uploaded: 2024-05-23T12:59:41.000Z
Duration: 1 min 16 s
Channel: JoVE

Bir transmisyon mili için gerekli olan tasarım özellikleri, şaft tarafından iletilen güç ve dönüş hızıdır.
Bu spesifikasyonlara dayanarak, milin malzeme ve kesit boyutları, gerekli gücü belirtilen hızda iletirken malzemenin izin verdiği maksimum kesme geriliminin elastik sınır içinde kalması sağlanarak seçilir.
Şimdi, bir sistemle ilişkili güç, uygulanan torka bağlıdır. Terimleri yeniden düzenleyerek, mile uygulanan tork hesaplanabilir. Bu denklem, milin hem güç gereksinimlerini hem de dönme frekansını hesaba katar.
Hesaplanan tork ve izin verilen maksimum gerilim daha sonra şaft yarıçapı için izin verilen minimum değeri belirlemek için elastik burulma formülünde uygulanır.
Katı dairesel bir şaft için, polar atalet momentinin şaftın yarıçapına bu oranı, şaft yarıçapının küpü olarak değişir. Bunun yerine, şaft yarıçapı için gereken minimum değeri verir.
İçi boş bir silindir için, milin dış yarıçapının izin verilen minimum değeri hesaplanır.

 transmisyon millerinin tasarımı

Bir transmisyon milinin tasarımı iki temel spesifikasyona tabidir: ilettiği güç ve dönme hızı. Bu parametreler, şaftın malzemesinin ve kesit boyutlarının seçimine rehberlik ederek, istenen gücü verilen hızda iletirken malzemenin maksimum kesme geriliminin elastik sınır içinde kalmasını sağlar. Sistemin gücü doğası gereği uygulanan torka bağlıdır. Şafta uygulanan tork, terimlerin yeniden yapılandırılmasıyla hesaplanabilir.

<img alt="Equation 1" src="/files/ftp_upload/15617/15617_Equation_1.svg" style="text-align: center; height: 38px;">

Bu hesaplamada hem güç gereksinimleri hem de şaftın dönüş hızı dikkate alınır. Tork ve izin verilen maksimum gerilim hesaplandıktan sonra bunlar elastik burulma formülüne dahil edilir. Bu işlem, şaft yarıçapı için izin verilen minimum değeri verir. Katı dairesel bir şaft durumunda, kutupsal eylemsizlik momentinin şaft yarıçapına oranı, şaft yarıçapının küpü kadar değişir. Şaft yarıçapı için gereken minimum değer, bu değerin değiştirilmesiyle hesaplanır.

<img alt="Equation 2" src="/files/ftp_upload/15617/15617_Equation_2.svg" style="text-align: center; height: 62px;">

İçi boş bir silindir şaft için hesaplamalar, şaftın dış yarıçapı için izin verilen minimum değeri verir. Sonuç olarak, bir transmisyon milinin tasarım süreci, güç, hız, gerilim sınırları ve fiziksel boyutların dikkatli bir şekilde dengelenmesinden oluşur.

<img alt="Equation 3" src="/files/ftp_upload/15617/15617_Equation_3.svg" style="text-align: center; height: 62px;">

 Transmisyon Millerinin Tasarımı

Bir transmisyon mili için gerekli olan tasarım özellikleri, şaft tarafından iletilen güç ve dönüş hızıdır.
Bu özelliklere dayanarak, ...

Education

JoVE Core

Mechanical Engineering

Makine Mühendisliği

Unit 1

Ünite 1

Torsion

Burulma

KEY TERMS AND CONCEPTS

TEMEL TERİMLER VE KAVRAMLAR

Design of Transmission Shafts

sizing a transmission shaft by torque

A transmission shaft is sized from the power it must carry and the speed it rotates at. These two design limits guide the choice of shaft material and cross-sectional size. The goal is to keep the maximum shearing stress within the elastic limit while still transmitting the needed power.

Power is directly linked to torque, which is the twisting force applied to the shaft. By rearranging the power relation, the torque can be found from the required power and the shaft speed. That torque value is then used with the maximum allowable stress in the elastic torsion formula.

The torsion calculation gives the minimum allowed shaft radius. For a solid circular shaft, the polar moment of inertia divided by the radius changes with the cube of the radius, so this value is used to find the minimum radius. For a hollow cylindrical shaft, the same process gives the minimum outer radius. In this way, shaft design balances power, speed, stress limits, and physical size.

Sizing a Transmission Shaft by Torque

stresses in a shaft

Torque and Shear in a Twisted Shaft

A shaft under torque develops internal shear forces as it twists. In this setup, equal and opposite torques act on the shaft PQ. To study the effect, a section is cut perpendicular to the shaft axis at an arbitrary point R. The free-body diagram of the QR segment shows the shearing forces applied by the PR portion. These forces act as the shaft resists twisting. Using equilibrium on the QR segment links the internal shear forces in the cut section to the internal torque. Here, r is the...

deformation in a circular shaft

Shear Strain in a Circular Shaft

Shear strain in a circular shaft describes how the shaft’s surface changes shape under torsion. A circular shaft keeps each cross-section flat and undistorted as it twists. Each section behaves like a rigid slab that rotates in place. To study the strain inside the shaft, consider a cylindrical section with length L and radius R. One end of this section is fixed. The radius at a point inside the section is labeled r. Before the load is applied, a small square element lies on the surface of...

circular shaft - stresses in linear range

Torsion Formula for Circular Shafts

Torsion in a circular shaft is analyzed when the applied torque stays within Hooke's law. In this linear range, the shaft does not undergo permanent deformation. The discussion uses shearing strain, shearing stress, and the modulus of rigidity to build the stress equation. The derivation also requires the moments of the small forces on a cross-section to equal the applied torque. When the shearing stress expression is rewritten, an integral term appears. This term represents the polar moment...

angle of twist - elastic range

Elastic Twist in a Circular Shaft

Elastic twist in a circular shaft describes how a cylindrical shaft rotates when torque is applied. The shaft has a length L and a uniform radius r. A torque at the free end creates shearing strain, which is greatest at points farther from the shaft axis. When the shaft stays within the elastic range, the shearing strain can be written in terms of the applied torque, radial distance, polar moment of inertia, and modulus of rigidity. The polar moment of inertia is a geometric measure of how the...

angle of twist: problem solving

Shaft Torsion Between Pulleys B and C

Shaft torsion between pulleys B and C is found by analyzing how torque twists an aluminum shaft. An electric motor applies 700 N·m of torque and produces stable rotation. The shaft carries pulleys B and C, which experience torques of 300 N·m and 400 N·m. The calculation starts with a section cut between pulleys B and C. A free-body diagram is used to study the cut cross-section. Because pulley B has an anticlockwise torque, the torque at the cut must balance it in the opposite direction. The...

design of transmission shafts

A transmission shaft is sized from the power it must carry and the speed it rotates at. These two design limits guide the choice of shaft material and cross-sectional size. The goal is to keep the maximum shearing stress within the elastic limit while still transmitting the needed power. Power is directly linked to torque, which is the twisting force applied to the shaft. By rearranging the power relation, the torque can be found from the required power and the shaft speed. That torque value...

stress concentrations in circular shafts

Why Shafts Develop Local Stress Peaks

Circular shafts can develop local stress peaks when torque is applied through real machine parts. The elastic torsion formula works best for a circular shaft with a uniform cross-section and rigid plates fixed to its ends. In practice, torque is often passed through flange couplings or gears, and these parts use keys in keyways to connect to the shaft. That loading method changes the stress pattern near the point where torque enters the shaft. The stress distribution no longer matches the...

plastic deformation in circular shafts

Torsional Failure and Plastic Strain in Shafts

Plastic deformation in circular shafts happens when torsional force pushes the material past its yield strength. At that point, the shaft does not return to its original shape. Instead, it keeps a permanent strain. To measure this change, the stress pattern inside the shaft must be understood. The maximum shearing stress is calculated first. Then a shearing-stress-strain diagram can be drawn to find the maximum shearing strain. Shearing strain changes linearly with the distance from the shaft...

circular shafts - elastoplastic materials

Torsion Limits in Circular Shafts

Circular shafts under torsion show a clear change from elastic behavior to plastic deformation as torque increases. In the elastic limit, stress rises in direct proportion to the distance from the shaft’s center. The outer material carries the highest stress first, and the shaft can still return to its original shape. At a critical stress level, the shaft begins to yield. This marks the maximum torque the shaft can carry without permanent deformation. Beyond this point, a plastic region forms...

residual stresses in circular shafts

Residual Stress After Shaft Torsion

Residual stress can remain in a circular shaft after torque causes plastic deformation. This happens in elastoplastic materials, which show both elastic and plastic behavior. The plastic change can come from high shearing stress or large strain. Residual stress is the internal stress that stays in the material after the external force is removed. In a shaft under torque, the angle of twist does not return fully to its original value. That lasting change shows that residual stress is still...

torsion of noncircular members

Torsion in Square and Rectangular Bars

Torsion in square and rectangular bars shows how shape changes the way a material twists. Circular shafts keep their cross-sections nearly unchanged because they are axis-symmetric. That symmetry helps the stress spread evenly, so the shaft can resist torsion without distorting. Square bars behave differently because they do not have the same axial symmetry. When twisted, their cross-sections distort, although the diagonals and the lines connecting the midpoints stay as exceptions. This means...

thin-walled hollow shafts

Shear Flow in Thin-Walled Shafts

Shear flow in a thin-walled hollow shaft describes how torsional force is carried through the wall. When a small segment of width dx is isolated, it is still in equilibrium, but it experiences torsional shearing forces at its ends. These forces come from the longitudinal shearing stress on the segment's minor surface multiplied by that surface area. The result is a uniform shear flow through the structure. To study the wall more closely, a small section with length ds is considered. The force...

key terms and concepts

Learn how transmission shaft size is set by power, speed, torque, and allowable shear stress. See how solid and hollow shafts are designed.

Sizing a Transmission Shaft by Torque | JoVE K12

JoVE Core Makine Mühendisliği, denge, kuvvetler, kafes kiriş analizi ve yapısal mekanik gibi temel konuları kapsayan kısa, anlaşılması kolay animasyonlu videolar sunar. Gerçek dünyadaki uygulamalarını keşfedin ve bilim insanlarının önderlik ettiği deneylerle bu kavramların uygulanmasına tanık olun.

mechanical engineering

Sizing a Transmission Shaft by Torque

Description

Transcript

Tags