Beer's Law

Source: Smaa Koraym at Johns Hopkins University, MD, USA

1. Preparation of SolutionsExpand

   Here, we show the laboratory preparation for 10 students working in pairs, with some excess. Please adjust quantities as needed.

   • To set up for this lab experiment, wear the appropriate personal protective equipment, including a lab coat, chemical splash goggles, and gloves. Note: You will be working with nitric acid, which is toxic and corrosive, so use caution when handling it. Let's start by preparing 1 L of 0.5 M nitric acid.
   • Measure out 32 mL of 15.7 M nitric acid, and carefully pour it into a 1-L volumetric flask via a funnel.
   • Add deionized water to the flask up to the mark. Place a stir bar in the flask and stir the solution. Label a 1-L brown glass bottle as '0.5 M nitric acid'.
   • Once the solution appears homogeneous, remove the stir bar and place a funnel in the mouth of the labeled bottle. Carefully pour the nitric acid solution into the bottle. Set the capped bottle of 0.5 M nitric acid at the back of the instructor's hood and store the concentrated nitric acid in a corrosives cabinet.
   • Prepare 125 mL of a 1 M iron(III) chloride solution in 0.5 M nitric acid. Measure out 125 mL of the just prepared 0.5 M nitric acid and pour it into a 250-mL Erlenmeyer flask using a clean funnel.
   • Bring a container of iron(III) chloride hexahydrate and a mortar and pestle to a top-loading balance. Measure at least 35 g and place it in the mortar.
   • Grind the clumps of iron(III) chloride hexahydrate to a fine consistency using the pestle. Then, measure 33.79 g of the powder and bring it to the fume hood. Transfer the powder to the flask of nitric acid with a powder funnel.
   • Place a magnetic stir bar in the flask and set it on a stirring hotplate. Stir the solution while heating at around 80 °C until it appears homogeneous. As the solution stirs, label a 125-mL brown glass bottle as '1.0 M iron(III) chloride in 0.5 M nitric acid'.
   • Once the iron(III) chloride solution appears homogeneous, remove the flask from the hotplate and retrieve the stir bar.
   • Allow the solution to cool to room temperature, then transfer it to the labeled bottle via the funnel. Cap the bottle and store the solution in a corrosives cabinet.
   • Lastly, prepare 250 mL of a 0.5 mM solution of sodium thiocyanate in 0.5 M nitric acid. Measure 250 mL of 0.5 M nitric acid and pour it into a 250-mL Erlenmeyer flask via a clean funnel.
   • Use an analytical balance to measure out 10.1 mg of sodium thiocyanate. Bring it back to the hood and pour it into the 250-mL flask of nitric acid. If necessary, use a small amount of nitric acid to wash any remaining sodium thiocyanate from the weighing boat.
   • Add a stir bar to the flask and stir the mixture at room temperature until it appears homogeneous. While the mixture stirs, label a 250-mL brown glass bottle as '5.00 x 10^-4 M sodium thiocyanate in 0.5 M nitric acid'.
   • Once the solution is thoroughly mixed, remove the stir bar and transfer the solution to the labeled bottle. Cap the bottle, then store both the sodium thiocyanate solution and the nitric acid in a corrosives cabinet.
   • When you have finished making the solutions, neutralize any acid waste, and wash the glassware and equipment using your standard procedures.
2. Preparation of the LaboratoryExpand
   • Place a waste container labeled for aqueous iron waste and a wash bottle filled with deionized water in a satellite waste hood.
   • Set aluminum foil, plastic paraffin film, and a pair of scissors in a central area. Ensure that each sink has a stock of paper towels.
   • Assemble the hand-held spectrophotometers and distribute them to the student workstations.
   • Set up a ring stand equipped with a burette clamp at each student hood.
   • Ensure that each workstation has the following glassware and lab equipment (we suggest that students work in pairs):

     1Box of laboratory wipes

     1Bag of baking soda

     1Roll of pH paper

     1Roll of laboratory paper

     1Pen

     250-mL glass burettes

     11-mL volumetric pipette

     25-mL volumetric pipettes

     110-mL volumetric pipette

     1Pipette bulb or controller

     150-mL volumetric flask

     3150-mL beakers

     1100-mL beaker

     550-mL beakers

     1400-mL beaker

     150-mL graduated cylinder

     110-mL graduated cylinder

     3Funnels

     1Glass stirring rod

     13.5-mL cuvette with cap

   • Distribute boxes of disposable pipettes around the lab so that students have access to extras.
   • Just before the lab, place the 0.5 M nitric acid, the 0.5 mM sodium thiocyanate, and the 1 M iron(III) chloride solutions in a central hood.