Name: A Flexible Wearable Supernumerary Robotic Limb for Chronic Stroke Patients (Video) | JoVE Journal
Uploaded: 2023-10-27T13:40:00.000+00:00
Duration: 3 min 55 s
Description: Learn how a flexible wearable robotic limb assists chronic stroke patients with finger rehabilitation and grasping tasks. This method uses bending sensors to interpret patient intentions and improve quality of life.

ai_agent_IP

ai_agent

maintenance

instantTrialDurationMinutes

isBiopharma

enableNewMyJoveSectionDesign

educationFeatures

seoMetaApi

ai_copilot_institution_blacklist

ai_chat_institution_blacklist

freeAccessWindow

ssoRoleCapture

scheduledMaintenanceBanner

joveLabsFeatures

disable_autoplay_for_bots

extended_trial_duration

5 minutes

This work is supported by the National Natural Science Foundation of China under Grant U1913207 and by the Program for HUST Academic Frontier Youth Team. The authors would like to thank the support from these foundations.

This protocol has been approved by the Ethics Review Board of Union Hospital, Tongji Medical College, Huazhong University of Science and Technology. Patients with upper limb functional disorders who met the diagnostic criteria and were receiving treatment at the author&#39;s hospital&#39;s rehabilitation department outpatient and inpatient units were selected as participants. The patients&#39; motor function recovery was assessed according to the Brunnstrom recovery stages21, and patients in stages 3-5 were chosen to participate in the experiments. Written informed consent was obtained from the patients who participated in the study. The procedure includes mold design for the pneumatic gripper, the fabrication process of the pneumatic gripper based on cured silicone rubber, integration of portable devices, and software and hardware implementation for grasp intention detection. Except for silicone rubber and common fabrics, all wearable components are produced using 3D printing technology (see Supplementary Coding Files 1-5).
1. Designing and fabricating the pneumatic gripper
<ol>
	<li>Assemble the pre-designed mold22 as shown in Figure 1A,B. Then use hot melt glue to secure the glass fibers at the designated positions in the mold, as depicted in Figure 1C. Ensure to use hot melt glue to seal any potential areas that may cause silicone leakage.</li>
	<li>Weigh an appropriate amount of Component A and Component B of the silicone elastomer (9:1 by weight) (see Table of Materials), and mix them in the specified ratio. After mixing, utilize a vacuum mixing and degassing machine with a variable centrifugal force, determined by the internal preset program of the machine. Once the mixture is ready, promptly inject it into the assembled mold, as illustrated in Figure 1D. 
	NOTE: The variable centrifugal force is controlled by the vacuum mixing and degassing machine through its internal preset program (see Table of Materials). The centrifugal force must be incrementally increased to ensure thorough mixing of the silicone rubber and the removal of any trapped air bubbles.</li>
	<li>Allow the mold to sit for approximately 30 s, then place it in a vacuum dryer for about 1 min to enable any small air bubbles in the silicone rubber to escape. Remove the mold from the dryer and place it as a whole in a thermostatic chamber set at 30 &#176;C for 12 h, allowing the silicone rubber to cure.</li>
	<li>Repeat the steps outlined in the second step by injecting the mixed silicone rubber into the mold shown in Figure 1E. Next, place the demolded rubber body shown in Figure 1F into the mold filled with silicone rubber. Put the entire assembly in a thermostatic chamber set at 30 &#176;C for 12 h to allow the silicone rubber to cure.</li>
	<li>Remove the cured silicone rubber body from the mold and trim off any excess silicone rubber. The fabrication of the flexible gripper is now complete. 
	&#8203;NOTE: The cavity consists of two sets of pneumatic grids, which are independent of each other. Due to the significant difference in elastic modulus between the glass fibers and the corrugated structure, the pneumatic gripper bends inward when inflated, allowing for envelope-grasping actions. The fingertip is designed with a protrusion resembling an elephant trunk, enabling fingertip-grasping actions.</li>
</ol>
2. Assembling the wearable flexible supernumerary robotic limb
NOTE: The wearable supernumerary robotic limb includes a mini air pump, air valves, a single-chip microcomputer, pneumatic gripper, power supply, flexible bending sensors, a wearable glove, and accessories for pneumatic and electrical connections (see Table of Materials), as shown in Figure 2.
<ol>
	<li>Meticulously handcraft the wearable glove with the help of a tailor. Ensure it undergoes multiple iterations and improvements based on wearer feedback and the tailor&#39;s experience.</li>
	<li>Secure the pneumatic gripper with 3D-printed parts and attach it to the appropriate position on the glove using adhesive tape.</li>
	<li>Embed three flexible bending sensors (see Table of Materials) as shown in Figure 3 into the glove. Place them on the index, middle, and ring fingers, respectively, aligning them with the backside of the fingers. Use a data acquisition card to record signals from the sensors.</li>
	<li>Amplify the sensor signals and route them to an Arduino (see Table of Materials). Process these signals using a sliding window and least squares filtering within the Arduino23. Utilize these estimated values as baseline data for intent detection.</li>
	<li>Place components such as the air pump, air valves, control board, and power supply into a backpack for portability. Refer to Figure 4 for a visual representation of the wearing effect.</li>
</ol>
3. Detecting the grasping intention
NOTE: When the wearer&#39;s fingers generate movement, the sensor feedback signal changes accordingly. It works by increasing the resistance in the circuit as the component bends more. Figure 5 shows the recorded signal values of the flexible bending sensor during the finger movement of one volunteer. The three curves correspond to the signals obtained from sensors placed on the three fingers. Patients with hemiparesis often have limited finger mobility, but the sensor is capable of detecting significant changes.
<ol>
	<li>Collect data on the range and pattern of sensor changes during finger movements. Select appropriate threshold values based on the detected sensor amplitude to control pump activation. Instruct participants to move their fingers freely within their range of ability. Determine the threshold values as the averages of the peak and valley values of the sensor feedback. 
	NOTE: When the sensor signal exceeds the set threshold value, the pump starts operating. The air pressure increases as the fingers bend further. Conversely, when the bending angle of the fingers decreases, and the sensor detects a signal below the threshold, the air valve releases the pressure to zero, and the pneumatic gripper releases.</li>
	<li>Ask the user to observe the state of the pneumatic gripper and determine the appropriate time to stop inflating the air and cease further finger bending.</li>
	<li>Repeat the above tests to establish a reasonable threshold and to become familiar with using this device.</li>
</ol>
4. Testing the device with healthy volunteers
<ol>
	<li>Enlist three healthy volunteers with normal upper limb motor abilities for the study to confirm the wearing and grasping effects of the prototype.</li>
	<li>Set the maximum air pressure for the pneumatic gripper to 100 kPa. Instruct the participants to flex and extend their fingers. Have the participants wear the prototype and conduct gripping and releasing experiments on objects of various shapes using the method mentioned earlier.</li>
	<li>Solicit feedback from the wearers regarding their experience and adjust the wearing scheme based on their suggestions. 
	&#8203;NOTE: As depicted in Figure 6, the participants successfully enveloped and grasped cylindrical objects of different sizes using the prototype. Additionally, they also completed fingertip grasping tasks on rectangular block-shaped objects.</li>
</ol>
5. Rehabilitation and grasp assistance for patients
<ol>
	<li>Evaluate the patients&#39; motor function recovery according to the Brunnstrom recovery stages21 by medical professionals. Only allow patients in stages 3-5 to participate in the experiments for rehabilitation training or daily assistance.</li>
	<li>Enlist six chronic hemiparetic patients to validate the reliability and effectiveness of the prototype. Instruct the patients to independently wear the glove (excluding the backpack) and move their fingers within their range of ability for calibrating the threshold values.</li>
	<li>During the rehabilitation phase, encourage patients to engage in various gripping tasks to exercise their finger muscles. Have the patients sit at the edge of a table and use the prototype to perform a series of grasping activities, including grasping a water bottle, a banana, a cube, and a toothbrush.</li>
	<li>Ask the patients to complete relevant survey questionnaires (Supplementary File 1) based on their personal experiences after the experiment. Assess the following six subjective feelings: confidence in the function of the system; ease of use; convenience and comfort of wearing it; effectiveness and usefulness for rehabilitation; effectiveness and usefulness in daily life; areas that still need improvement.</li>
	<li>Rate their responses on a scale of 1 to 5, where 1 represents strongly disagree and 5 represents strongly agree. Record the data and analyze the issues with the prototype and potential areas for improvement based on the questionnaire. 
	NOTE: This not only adds interest to the rehabilitation training but also enhances the patient&#39;s willingness to participate in the recovery process. In cases where patients have reached a stable condition but still struggle to perform gripping tasks with their fingers, the use of the robotic limb can assist in carrying out certain daily grasping actions required for everyday life.</li>
</ol>

Revolutionizing Stroke Rehabilitation with Enhanced Grasping and Finger Recovery

<ol><li>Feigin, V. L., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Global%2C+regional%2C+and+national+burden+of+stroke+and+its+risk+factors%2C+1990-2019%3A+A+systematic+analysis+for+the+global+burden+of+disease+study+2019%5BTitle%5D)+AND+%22The+Lancet+Neurology%22%5BJournal%5D)">Global, regional, and national burden of stroke and its risk factors, 1990-2019: A systematic analysis for the global burden of disease study 2019.</a> The Lancet Neurology. 20 (10), 795-820 (2021).</li>
<li>Nakayma, H., Jørgensen, H. S., Raaschou, H. O., Olsen, T. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Compensation+in+recovery+of+upper+extremity+function+after+stroke%3A+The+copenhagen+stroke+study%5BTitle%5D)+AND+%22Archives+of+Physical+Medicine+and+Rehabilitation%22%5BJournal%5D)">Compensation in recovery of upper extremity function after stroke: The copenhagen stroke study.</a> Archives of Physical Medicine and Rehabilitation. 75 (8), 852-857 (1994).</li>
<li>Faria-Fortini, I., Michaelsen, S. M., Cassiano, J. G., Teixeira-Salmela, L. F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Upper+extremity+function+in+stroke+subjects%3A+Relationships+between+the+international+classification+of+functioning%2C+disability%2C+and+health+domains%5BTitle%5D)+AND+%22Journal+of+Hand+Therapy%22%5BJournal%5D)">Upper extremity function in stroke subjects: Relationships between the international classification of functioning, disability, and health domains.</a> Journal of Hand Therapy. 24 (3), 257-265 (2011).</li>
<li>Al-Fahaam, H., Davis, S., Nefti-Meziani, S., Theodoridis, T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Novel+soft+bending+actuator-based+power+augmentation+hand+exoskeleton+controlled+by+human+intention%5BTitle%5D)+AND+%22Intelligent+Service+Robotics%22%5BJournal%5D)">Novel soft bending actuator-based power augmentation hand exoskeleton controlled by human intention.</a> Intelligent Service Robotics. 11, 247-268 (2018).</li>
<li>IEEE International Conference on Robotics and Automation (ICRA). Thalman, C. M., Hsu, J., Snyder, L., Polygerinos, P. 2019 International Conference on Robotics and Automation (ICRA), , IEEE. 8436-8442 (2019).</li>
<li>Miron, G., Plante, J. S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Design+principles+for+improved+fatigue+life+of+high-strain+pneumatic+artificial+muscles%5BTitle%5D)+AND+%22Soft+Robotics%22%5BJournal%5D)">Design principles for improved fatigue life of high-strain pneumatic artificial muscles.</a> Soft Robotics. 3 (4), 177-185 (2016).</li>
<li>IEEE International Conference on Robotics and Automation (ICRA). Yun, Y., et al. 2017 IEEE International Conference on Robotics and Automation (ICRA), , IEEE. 2904-2910 (2017).</li>
<li>Tran, P., Jeong, S., Herrin, K. R., Desai, J. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Hand+exoskeleton+systems%2C+clinical+rehabilitation+practices%2C+and+future+prospects%5BTitle%5D)+AND+%22IEEE+Transactions+on+Medical+Robotics+and+Bionics%22%5BJournal%5D)">Hand exoskeleton systems, clinical rehabilitation practices, and future prospects.</a> IEEE Transactions on Medical Robotics and Bionics. 3 (3), 606-622 (2021).</li>
<li>Dynamic Systems and Control Conference. Ort, T., Wu, F., Hensel, N. C., Asada, H. H. Dynamic Systems and Control Conference, , V002T027A010 American Society of Mechanical Engineers. (2023).</li>
<li>Hussain, I., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((A+soft+supernumerary+robotic+finger+and+mobile+arm+support+for+grasping+compensation+and+hemiparetic+upper+limb+rehabilitation%5BTitle%5D)+AND+%22Robotics+and+Autonomous+Systems%22%5BJournal%5D)">A soft supernumerary robotic finger and mobile arm support for grasping compensation and hemiparetic upper limb rehabilitation.</a> Robotics and Autonomous Systems. 93, 1-12 (2017).</li>
<li>Yang, B., Huang, J., Chen, X., Xiong, C., Hasegawa, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Supernumerary+robotic+limbs%3A+A+review+and+future+outlook%5BTitle%5D)+AND+%22IEEE+Transactions+on+Medical+Robotics+and+Bionics%22%5BJournal%5D)">Supernumerary robotic limbs: A review and future outlook.</a> IEEE Transactions on Medical Robotics and Bionics. 3 (3), 623-639 (2021).</li>
<li>Tong, Y., Liu, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Review+of+research+and+development+of+supernumerary+robotic+limbs%5BTitle%5D)+AND+%22IEEE%2FCAA+Journal+of+Automatica+Sinica%22%5BJournal%5D)">Review of research and development of supernumerary robotic limbs.</a> IEEE/CAA Journal of Automatica Sinica. 8 (5), 929-952 (2021).</li>
<li>Yap, H. K., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((A+magnetic+resonance+compatible+soft+wearable+robotic+glove+for+hand+rehabilitation+and+brain+imaging%5BTitle%5D)+AND+%22IEEE+Transactions+on+Neural+Systems+and+Rehabilitation+Engineering%22%5BJournal%5D)">A magnetic resonance compatible soft wearable robotic glove for hand rehabilitation and brain imaging.</a> IEEE Transactions on Neural Systems and Rehabilitation Engineering. 25 (6), 782-793 (2016).</li>
<li>Yun, S. S., Kang, B. B., Cho, K. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Exo-glove+pm%3A+An+easily+customizable+modularized+pneumatic+assistive+glove%5BTitle%5D)+AND+%22IEEE+Robotics+and+Automation+Letters%22%5BJournal%5D)">Exo-glove pm: An easily customizable modularized pneumatic assistive glove.</a> IEEE Robotics and Automation Letters. 2 (3), 1725-1732 (2017).</li>
<li>IEEE International Workshop on Intelligent Robots and Systems (IROS). Polygerinos, P., et al. 2013 IEEE/RSJ International Conference on Intelligent Robots and Systems, , IEEE. 1512-1517 (2013).</li>
<li>IEEE International Conference on Soft Robotics (RoboSoft). Stilli, A., et al. 2018 IEEE International Conference on Soft Robotics (RoboSoft), , IEEE. 579-584 (2018).</li>
<li>Zhang, D., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Making+sense+of+spatio-temporal+preserving+representations+for+eeg-based+human+intention+recognition%5BTitle%5D)+AND+%22IEEE+Transactions+on+Cybernetics%22%5BJournal%5D)">Making sense of spatio-temporal preserving representations for eeg-based human intention recognition.</a> IEEE Transactions on Cybernetics. 50 (7), 3033-3044 (2019).</li>
<li>IEEE International Workshop on Robot and Human Communication (ROMAN). Sirintuna, D., Ozdamar, I., Aydin, Y., Basdogan, C. 2020 29th IEEE International Conference on Robot and Human Interactive Communication (RO-MAN), , IEEE. 1280-1287 (2020).</li>
<li>2020 10th Annual Computing and Communincation Workshop and Conferenece (CCWC). Mahmud, S., Lin, X., Kim, J. H. 2020 10th Annual Computing and Communication Workshop and Conference (CCWC), , IEEE. 0768-0773 (2020).</li>
<li>Asghar, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Review+on+electromyography+based+intention+for+upper+limb+control+using+pattern+recognition+for+human-machine+interaction%5BTitle%5D)+AND+%22Proceedings+of+the+Institution+of+Mechanical+Engineers%2C+Part+H%3A+Journal+of+Engineering+in+Medicine%22%5BJournal%5D)">Review on electromyography based intention for upper limb control using pattern recognition for human-machine interaction.</a> Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine. 236 (5), 628-645 (2022).</li>
<li>Naghdi, S., Ansari, N. N., Mansouri, K., Hasson, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((A+neurophysiological+and+clinical+study+of+brunnstrom+recovery+stages+in+the+upper+limb+following+stroke%5BTitle%5D)+AND+%22Brain+Injury%22%5BJournal%5D)">A neurophysiological and clinical study of brunnstrom recovery stages in the upper limb following stroke.</a> Brain Injury. 24 (11), 1372-1378 (2010).</li>
<li>Ru, H., Huang, J., Chen, W., Xiong, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Modeling+and+identification+of+rate-dependent+and+asymmetric+hysteresis+of+soft+bending+pneumatic+actuator+based+on+evolutionary+firefly+algorithm%5BTitle%5D)+AND+%22Mechanism+and+Machine+Theory%22%5BJournal%5D)">Modeling and identification of rate-dependent and asymmetric hysteresis of soft bending pneumatic actuator based on evolutionary firefly algorithm.</a> Mechanism and Machine Theory. 181, 105169(2023).</li>
<li>Qin, L., Wu, W., Tian, Y., Xu, W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Lidar+filtering+of+urban+areas+with+region+growing+based+on+moving-window+weighted+iterative+least-squares+fitting%5BTitle%5D)+AND+%22IEEE+Geoscience+and+Remote+Sensing+Letters%22%5BJournal%5D)">Lidar filtering of urban areas with region growing based on moving-window weighted iterative least-squares fitting.</a> IEEE Geoscience and Remote Sensing Letters. 14 (6), 841-845 (2017).</li>
<li>Liu, S., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((A+two-finger+soft-robotic+gripper+with+enveloping+and+pinching+grasping+modes%5BTitle%5D)+AND+%22IEEE%2FASME+Transactions+on+Mechatronics%22%5BJournal%5D)">A two-finger soft-robotic gripper with enveloping and pinching grasping modes.</a> IEEE/ASME Transactions on Mechatronics. 26 (1), 146-155 (2020).</li>
<li>Tawk, C., Sariyildiz, E., Alici, G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Force+control+of+a+3D+printed+soft+gripper+with+built-in+pneumatic+touch+sensing+chambers%5BTitle%5D)+AND+%22Soft+Robotics%22%5BJournal%5D)">Force control of a 3D printed soft gripper with built-in pneumatic touch sensing chambers.</a> Soft Robotics. 9 (5), 970-980 (2022).</li>
<li>Zuo, W., Song, G., Chen, Z. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Grasping+force+control+of+robotic+gripper+with+high+stiffness%5BTitle%5D)+AND+%22IEEE%2FASME+Transactions+on+Mechatronics%22%5BJournal%5D)">Grasping force control of robotic gripper with high stiffness.</a> IEEE/ASME Transactions on Mechatronics. 27 (2), 1105-1116 (2021).</li>
<li>Watanabe, T., Morino, K., Asama, Y., Nishitani, S., Toshima, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Variable-grasping-mode+gripper+with+different+finger+structures+for+grasping+small-sized+items%5BTitle%5D)+AND+%22IEEE+Robotics+and+Automation+Letters%22%5BJournal%5D)">Variable-grasping-mode gripper with different finger structures for grasping small-sized items.</a> IEEE Robotics and Automation Letters. 6 (3), 5673-5680 (2021).</li>
</ol>

The authors have nothing to disclose.

This study presents an innovative, flexible, wearable supernumerary robotic limb designed to assist chronic stroke patients in finger rehabilitation and gripping tasks. This robotic system prioritizes portability and offers both envelope grasp and fingertip grasp functionalities. It incorporates a flexible bending sensor for user-friendly human-machine interaction control. Static grasping experiments validate the gripping capabilities of the designed mechanism in two distinct grasping modes. The study involves experiment...

According to previous research1, as of 2019, there were more than 100 million cases of stroke worldwide. Approximately two-thirds of these cases resulted in hemiplegic sequelae, and over 80% of severe hemiplegic stroke patients could not fully recover hand and arm function2. Furthermore, the aging population is expected to continue growing in the coming decades, leading to a significant increase in the number of potential stroke victims. The persistent upper extremity impairments following a stroke can significantly affect activities of daily living (ADLs), and hand rehabilitation has been clinically recognized as a critical objective for enhancing the activity and participation of chronic stroke patients3.
Traditional motor-driven robotic upper limb devices can provide substantial driving force, but their rigid structures often translate into large sizes and high weights. Moreover, they pose the risk of causing irreversible harm to the human body if they were to malfunction. In contrast, soft pneumatic actuators have demonstrated considerable potential in rehabilitation4, assistance5, and surgical applications6. Their advantages include safety, lightweight construction, and inherent compliance.
In recent years, numerous flexible wearable robots have emerged, designed and developed around soft pneumatic actuators. These robots have been intended for the rehabilitation and post-rehabilitation assistance of stroke patients&#39; upper limbs. They primarily encompass hand exoskeletons7,8, and supernumerary limbs9,10. Although both are used in the fields of wearable robotics and rehabilitation, the former directly interacts with the human body, potentially constraining muscles or joints, while the latter supplements the human workspace or movement without direct constraint11,12. Wearable supernumerary robotic fingers based on servo motors were developed to assist occupational therapists in activities of daily living (ADLs) training9. A similar approach can be found in other research10. These two categories of robotic fingers have introduced novel possibilities for the application of such robots in the rehabilitation assistance of hemiparetic patients. Nonetheless, it is worth noting that the rigid structure employed in these robotic designs may introduce potential considerations regarding user comfort and safety. The design, fabrication, and evaluation of a soft wearable robotic glove were presented13, which can be used for hand rehabilitation and task-specific training during functional Magnetic Resonance Imaging (fMRI). The glove utilizes soft pneumatic actuators made of silicone elastomers to generate finger joint motion, and the device is MR-compatible without causing artifacts in fMRI images. Yun et al. introduced the Exo-Glove PM, a customizable soft pneumatic assistive glove that utilizes an assembly-based approach14. This innovative design features small modules and adjustable distances between them, allowing users to customize the glove based on their phalange length using spacers. This approach maximizes comfort and performance without the need for custom manufacturing. Researchers presented soft actuators composed of elastomeric materials with integrated channels functioning as pneumatic networks15. These actuators generate bending motions that safely conform to human finger movements. Additionally, researchers introduced the AirExGlove, a lightweight and adaptable inflatable soft exoskeleton device16. This system is cost-effective, customizable for different hand sizes, and has successfully accommodated patients with varying levels of muscle spasticity. It offers a more ergonomic and flexible solution compared to rigid-linked robotic systems. While these studies have made significant contributions to the development of flexible wearable hand rehabilitation and assistive robots, it&#39;s worth noting that none of them have achieved complete portability and human-robot interaction control.
Numerous studies have explored the correlation between biological signals, such as electroencephalogram (EEG)17 or electromyogram (EMG) signals18, and human intention. However, both approaches have certain limitations within the constraints of existing devices and technological conditions. Invasive electrodes require surgical procedures on the human body, while non-invasive electrodes suffer from issues such as high noise levels and unreliability in signal acquisition. Detailed discussions of these limitations can be found in the literature19,20. Therefore, the pursuit of research into the portability and user-friendly human-machine interaction capabilities of flexible wearable supernumerary robotic limbs remains highly relevant.
In this study, a unique flexible wearable supernumerary robotic limb was designed and fabricated to assist chronic stroke patients in finger rehabilitation and gripping assistance. This robotic limb is characterized by its lightweight, safety, compliance, waterproofing, and impressive output-to-weight/pressure ratio. Two gripping modes, envelope and fingertip grasping, have been achieved while maintaining portability and ensuring a user-friendly human-robot interaction. The protocol details the design and fabrication process of the pneumatic gripper and the wearable scheme. Additionally, a human-robot interaction method based on flexible bending sensors has been proposed, allowing for convenient and user-friendly control through threshold segmentation. All these aspects have been validated through practical experiments.
The main contributions of this study are summarized as follows: (1) A lightweight, friendly, and wearable flexible supernumerary robotic limb for chronic stroke patients has been designed and fabricated. (2) A reliable method of human-robot interaction has been realized based on flexible bending sensors. (3) Real-world experiments have been conducted to verify the effectiveness and reliability of the proposed mechanism and method, which include output force testing and involve six chronic stroke patients.

<table><tbody><tr><td>Air Compressor</td><td>Xinweicheng</td><td>F35L-JJ-24V</td><td>Provide air supply for the pneumatic gripper</td></tr><tr><td>Arduino&amp;nbsp;</td><td>Emakefun</td><td>Mega 2560</td><td>Single-chip microcomputer/data acquisition card</td></tr><tr><td>Backpack</td><td>Mujin</td><td></td><td>Integrating external devices</td></tr><tr><td>Flex Sensor</td><td>Spectra Symbol</td><td>Flex Sensor 2.2</td><td>Flexible bending sensors</td></tr><tr><td>Power supply</td><td>Yisenneng</td><td>YSN-37019200</td><td>Provide power</td></tr><tr><td>PU quick-plug connector</td><td>Elecall</td><td>PU-6</td><td>Connector for PU tube</td></tr><tr><td>PU tube</td><td>Baishehui</td><td>ZDmJKJJy</td><td>Air line connection</td></tr><tr><td>Silicone elastomer</td><td>Wacker</td><td>ELASTOSIL M4601 A/B</td><td>Material of the pneumatic gripper</td></tr><tr><td>Thermostatic chamber</td><td>Ruyi</td><td>101-00A</td><td>Constant temperature to accelerate the curing of silicone</td></tr><tr><td>Vacuum dryer</td><td>Fujiwara</td><td>PC-3</td><td>Further defoaming</td></tr><tr><td>Vacuum mixing and degassing machine</td><td>Smida</td><td>TMV-200T</td><td>Mix silicone thoroughly and get it defoamed</td></tr><tr><td>Valve</td><td>SMC</td><td>NTV1030-312CL</td><td>Control the air pressure</td></tr></tbody></table>

a flexible wearable supernumerary robotic limb for chronic stroke patients

A Flexible Wearable Supernumerary Robotic Limb for Chronic Stroke Patients

In this study, we present a flexible wearable supernumerary robotic limb that helps chronic stroke patients with finger rehabilitation and grasping movements. The design of this innovative limb draws inspiration from bending pneumatic muscles and the unique characteristics of an elephant's trunk tip. It places a strong emphasis on crucial factors such as lightweight construction, safety, compliance, waterproofing, and achieving a high output-to-weight/pressure ratio. The proposed structure enables the robotic limb to perform both envelope and fingertip grasping. Human-robot interaction is facilitated through a flexible bending sensor, detecting the wearer's finger movements and connecting them to motion control via a threshold segmentation method. Additionally, the system is portable for versatile daily use. To validate the effectiveness of this innovation, real-world experiments involving six chronic stroke patients and three healthy volunteers were conducted. The feedback received through questionnaires indicates that the designed mechanism holds immense promise in assisting chronic stroke patients with their daily grasping activities, potentially improving their quality of life and rehabilitation outcomes.

Output force experiments 
Figure 7 vividly depicts the structural design and dimensions of our actuator, providing a cross-sectional illustration. This actuator comprises two distinct sets of chambers, each containing five elegantly curved air chambers. Remarkably, at the actuator's terminus, we have ingeniously integrated a protruding structure, reminiscent of an elephant's trunk tip, significantly expanding the actuator's gripping radius.
To ...

This protocol introduces a flexible wearable supernumerary robotic limb tailored to assist in finger rehabilitation for stroke patients. The design incorporates a bending sensor to facilitate seamless human-robot interaction. Validation through experiments involving both healthy volunteers and stroke patients underscores the efficacy and dependability of the proposed study.

In this study, we present a flexible wearable supernumerary robotic limb that helps chronic stroke patients with finger rehabilitation and grasping ...

a-flexible-wearable-supernumerary-robotic-limb-for-chronic-stroke

Research

JoVE Journal

Engineering

This study reports the development of a novel robot-assisted task-oriented program for hand rehabilitation. The developmental process consists of experiments using both healthy subjects and subjects who have had a stroke and suffered from subsequent motor control dysfunction.

Development of a Novel Task-oriented Rehabilitation Program using a Bimanual Exoskeleton Robotic Hand

Chronic stroke patients' insured rehabilitation is generally time limited. Imaging-based study of brain activity from walking-related motor tasks can lead to establishing biomarkers to measure improved outcomes and justify extending tailored therapy. A novel, magnetic resonance-compatible, variable-resistance foot motion device and a protocol for use during functional magnetic resonance imaging are presented.

Use of a Foot-Induced Digitally Controlled Resistance Device for Functional Magnetic Resonance Imaging Evaluation in Patients with Foot Paresis

It is estimated that 1 in 6 individuals worldwide will have a stroke in their lifetime, causing long-term disability, whose rehabilitation mechanisms are still poorly understood. This study proposes a protocol to evaluate brain activation by functional near-infrared spectroscopy (fNIRS) during a lower limb robotic therapy session.

An Experiment Using Functional Near-Infrared Spectroscopy and Robot-Assisted Multi-Joint Pointing Movements of the Lower Limb

This protocol describes an upper limb rehabilitation robot that provides intelligent feedback through four modes. These modes enhance upper limb function and flexibility, thereby improving patients' quality of life.

Enhancing Upper Limb Function and Motor Skills Post-Stroke Through an Upper Limb Rehabilitation Robot

This experimental protocol outlines the use of a dual upper limb task-oriented robotic system for stroke patients with upper limb dysfunction. The findings indicate that this system can significantly improve stroke patients' upper limb function and daily living activities.

Application of a Dual Upper Limb Task-Oriented Robotic System for the Functional Recovery of the Upper Limb in Stroke Patients

This study introduces a brain-computer interface (BCI) system for stroke patients, which combines electroencephalography and electrooculography signals to control an upper limb robotic hand, enhancing daily activities. The evaluation used the Berlin Bimanual Test for Stroke (BeBiTS).

Brain-Computer Interface-controlled Upper Limb Robotic System for Enhancing Daily Activities in Stroke Patients

This protocol aims to evaluate the clinical efficacy and patient comfort of using bedside lower limb rehabilitation robots for post-stroke hemiplegia rehabilitation, comparing outcomes with those of traditional manual therapy through randomized controlled trials.

Application of Bedside Lower Extremity Rehabilitation Robots in Stroke Rehabilitation: A Randomized Controlled Trial

A robotic platform is described that will be used to study the hydrodynamic performance—forces and flowfields—of the swimming California sea lion. The robot is a model of the animal's foreflipper that is actuated by motors to replicate the motion of its propulsive stroke (the 'clap').

A Robotic Platform to Study the Foreflipper of the California Sea Lion

This protocol describes a solution-based fabrication strategy for high-performance, flexible, transparent electrodes with fully-embedded, thick metal mesh. Flexible transparent electrodes fabricated by this process demonstrate among the highest reported performances, including ultra-low sheet resistance, high optical transmittance, mechanical stability under bending, strong substrate adhesion, surface smoothness, and environmental stability.

Scalable Solution-processed Fabrication Strategy for High-performance, Flexible, Transparent Electrodes with Embedded Metal Mesh

In this paper, we present a protocol to directly grow an epitaxial yet flexible lead zirconium titanate memory element on muscovite mica.

A Fabrication and Measurement Method for a Flexible Ferroelectric Element Based on Van Der Waals Heteroepitaxy

Learn how a flexible wearable robotic limb assists chronic stroke patients with finger rehabilitation and grasping tasks. This method uses bending sensors to interpret patient intentions and improve quality of life.

A Flexible Wearable Supernumerary Robotic Limb for Chronic Stroke Patients

Explore More Videos