a-microfluidic-platform-for-precision-small-volume-sample-processing

A Microfluidic Platform for Precision Small-volume Sample Processing and Its Use to Size Separate Biological Particles with an Acoustic Microdevice

A major advantage of microfluidic devices is the ability to manipulate small sample volumes, thus reducing reagent waste and preserving precious sample. ...

Lawrence Livermore National Laboratory

Integrated surface plasmon resonance biosensors promise to enable compact and portable biosensing at high sensitivities. To replace the far field detector traditionally used to detect surface plasmons we integrate a near field detector below a functionalized gold film. The evanescent field of a surface plasmon at the aqueous-gold interface is converted into photocurrent by a thin film organic heterojunction diode. We demonstrate that use of the near field detector is equivalent to the traditional far field measurement of reflectivity. The sensor is stable and reversible in an aqueous environment for periods of 6 hrs. For specific binding of neutravidin, the detection limit is 4 microg/cm(2). The sensitivity can be improved by reducing surface roughness of the gold layers and optimization of the device design. From simulations, we predict a maximum sensitivity that is two times lower than a comparable conventional SPR biosensor.

Near field detector for integrated surface plasmon resonance biosensor applications.

We investigate tunable plasmon resonant cavity arrays in paired parallel nanowire waveguides. Resonances are observed when the waveguide length is an odd multiple of quarter plasmon wavelengths, consistent with boundary conditions of node and antinode at the ends. Two nanowire waveguides satisfy the dispersion relation of a planar metal-dielectric-metal waveguide of equivalent width equal to the square field average weighted gap. Confinement factors over 10(3) are possible due to plasmon focusing in the interwire space.

Plasmon resonant cavities in vertical nanowire arrays.

Surface enhanced Raman spectroscopy (SERS) has been increasingly utilized as an analytical technique with significant chemical and biological applications (Qian et al 2008 Nat. Biotechnol. 26 83; Fujita et al 2009 J. Biomed. Opt. 14 024038; Chou et al 2008 Nano Lett.8 1729; Culha et al 2003 Anal. Chem. 75 6196; Willets K A 2009 Anal. Bioanal. Chem. 394 85; Han et al 2009 Anal. Bioanal. Chem. 394 1719; Sha et al 2008 J. Am. Chem. Soc. 130 17214). However, production of a robust, homogeneous and large-area SERS substrate with the same ultrahigh sensitivity and reproducibility still remains an important issue. Here, we describe a large-area ultrahigh-uniformity tapered silver nanopillar array made by laser interference lithography on the entire surface of a 6 inch wafer. Also presented is the rigorous optical characterization method of the tapered nanopillar substrate to accurately quantify the Raman enhancement factor, uniformity and repeatability. An average homogeneous enhancement factor of close to 10(8) was obtained for benzenethiol adsorbed on a silver-coated nanopillar substrate.

Rigorous surface enhanced Raman spectral characterization of large-area high-uniformity silver-coated tapered silica nanopillar arrays.

Programmable positioning of 2 μm polystyrene (PS) beads with single particle precision and location selective, "on-demand", particle deposition was demonstrated by utilizing patterned electrodes and electrophoretic deposition (EPD). An electrode with differently sized hole patterns, from 0.5 to 5 μm, was used to illustrate the discriminatory particle deposition events based on the voltage and particle-to-hole size ratio. With decreasing patterned hole size, a larger electric field was required for a particle deposition event to occur in that hole. For the 5 μm hole, particle deposition began to occur at 10 V/cm where as an electric field of 15 V/cm was required for particles to begin depositing in the 2 μm holes. The likelihood of particle depositions continued to increase for smaller sized holes as the electric field increased. Eventually, a monolayer of particles began to form at approximately 20 V/cm. In essence, a voltage threshold was found for each hole pattern of different sizes, allowing fine adjustments in pattern hole size and voltage to control when a particle deposition event took place, even with the patterns on the same electrode. This phenomenon opens a route toward controlled, multimaterial deposition and assembly onto substrates without repatterning of the electrode or complicated surface modification of the particles. An analytical approach using the theories for electrophoresis and dielectrophoresis found the former to be the dominating force for depositing a particle into a patterned hole. Ebeam lithography was used to pattern spherical holes in precise configurations onto electrode surfaces, where each hole accompanied a polystyrene (PS) particle placement and attachment during EPD. The versatility of e-beam lithography was utilized to create arbitrary pattern configurations to fabricate particle assemblies of limitless configurations, enabling fabrication of unique materials assemblies and interfaces.

Article	Year
Near field detector for integrated surface plasmon resonance biosensor applications. Optics express\| PubMed ID: 19129901	2009
Plasmon resonant cavities in vertical nanowire arrays. Nano letters\| PubMed ID: 20698595	2010
Rigorous surface enhanced Raman spectral characterization of large-area high-uniformity silver-coated tapered silica nanopillar arrays. Nanotechnology\| PubMed ID: 20808033	2010
On-demand and location selective particle assembly via electrophoretic deposition for fabricating structures with particle-to-particle precision. Langmuir : the ACS journal of surfaces and colloids\| PubMed ID: 25314133	2015

Mihail Bora

Biography

JoVE Journal Publications

Other Publications