fabricating-degradable-thermoresponsive-hydrogels-on-multiple-length

Fabricating Degradable Thermoresponsive Hydrogels on Multiple Length Scales via Reactive Extrusion, Microfluidics, Self-assembly, and Electrospinning

While various smart materials have been explored for a variety of biomedical applications (e.g., drug delivery, tissue engineering, bioimaging, etc.), ...

McMaster University

A simple, rapid, solvent-free, and scalable thermally driven self-assembly approach is described to produce monodisperse, covalently cross-linked, and degradable poly(N-isopropylacrylamide) (PNIPAM) microgels based on mixing hydrazide (PNIPAM-Hzd) and aldehyde (PNIPAM-Ald) functionalized PNIPAM precursors. Preheating of a seed PNIPAM-Hzd solution above its phase transition temperature produces nanoaggregates that are subsequently stabilized and cross-linked by the addition of PNIPAM-Ald. The ratio of PNIPAM-Hzd:PNIPAM-Ald used to prepare the microgels, the time between PNIPAM-Ald addition and cooling, the temperature to which the PNIPAM-Hzd polymer solution is preheated, and the concentration of PNIPAM-Hzd in the initial seed solution can all be used to control the size of the resulting microgels. The microgels exhibit similar thermal phase transition behavior to conventional precipitation-based microgels but are fully degradable into oligomeric precursor polymers. The microgels can also be lyophilized and redispersed without any change in colloidal stability or particle size and exhibit no significant cytotoxicity in vitro. We anticipate that microgels fabricated using this approach may facilitate translation of the attractive properties of such microgels in vivo without the concerns regarding microgel clearance that exist with other PNIPAM-based microgels. 

Temperature-Induced Assembly of Monodisperse, Covalently Cross-Linked, and Degradable Poly(N-isopropylacrylamide) Microgels Based on Oligomeric Precursors.

Highly monodisperse and hydrolytically degradable thermoresponsive microgels on the tens-to-hundreds of micron size scale have been fabricated based on simultaneous on-chip mixing and emulsification of aldehyde and hydrazide-functionalized poly(N-isopropylacrylamide) precursor polymers. The microfluidic chip can run for extended periods without upstream gelation and can produce monodisperse (<10% particle size variability) microgels on the size range of ∼30-90 μm, with size tunable according to the flow rate of the oil continuous phase. Fluorescence analysis indicates a uniform distribution of each reactive pre-polymer inside the microgels while micromechanical testing suggests that smaller microfluidic-produced microgels exhibit significantly higher compressive moduli compared to bulk hydrogels of the same composition, an effect we attribute to improved mixing (and thus crosslinking) of the precursor polymer solutions within the microfluidic device. The microgels retain the reversible volume phase transition behavior of conventional microgels but can be hydrolytically degraded back into their oligomeric precursor polymer fragments, offering potential for microgel clearance following use in vivo.

Microfluidic production of degradable thermoresponsive poly(N-isopropylacrylamide)-based microgels.

The internal morphology of temperature-responsive degradable poly(N-isopropylacrylamide) (PNIPAM) microgels formed via an aqueous self-assembly process based on hydrazide and aldehyde-functionalized PNIPAM oligomers is investigated. A combination of surface force measurements, small angle neutron scattering (SANS), and ultrasmall angle neutron scattering (USANS) was used to demonstrate that the self-assembled microgels have a homogeneously cross-linked internal structure. This result is surprising given the sequential addition process used to fabricate the microgels, which was expected to result in a densely cross-linked shell-diffuse core structure. The homogeneous internal structure identified is also significantly different than conventional microgels prepared via precipitation polymerization, which typically exhibit a diffuse shell-dense core structure. The homogeneous structure is hypothesized to result from the dynamic nature of the hydrazone cross-linking chemistry used to couple with the assembly conditions chosen that promote polymer interdiffusion. The lack of an internal cross-linking gradient within these degradable and monodisperse microgels is expected to facilitate more consistent drug release over time, improved optical properties, and other potential application benefits.

Article	Year
Temperature-Induced Assembly of Monodisperse, Covalently Cross-Linked, and Degradable Poly(N-isopropylacrylamide) Microgels Based on Oligomeric Precursors. Langmuir : the ACS journal of surfaces and colloids\| PubMed ID: 25977976	2015
Microfluidic production of degradable thermoresponsive poly(N-isopropylacrylamide)-based microgels. Soft matter\| PubMed ID: 29177347	2017
Dynamically Cross-Linked Self-Assembled Thermoresponsive Microgels with Homogeneous Internal Structures. Langmuir : the ACS journal of surfaces and colloids\| PubMed ID: 29261314	2018

Eva Mueller

Biography

JoVE Journal Publications

Other Publications