Name: supernode equations in nodal analysis
Uploaded: 2025-05-22T09:06:13.000Z
Duration: 1 min 11 s
Channel: JoVE

节点分析可以有效地简化对具有相关或独立电压源的电路的分析。
考虑一个具有四个电阻器和两个电压源的电路，以便在非参考节点和参考节点之间连接一个电压源。
在这里，非参考节点的电压可以写成等于源的电压。
另一个电压源连接在两个非参考节点之间。这些节点形成超级节点或广义节点。
要分析具有超节点的电路，必须同时应用基尔霍夫电流定律和电压定律来确定节点电压。
首先，将基尔霍夫电流定律应用于超节点，考虑通过每个元件的电流。获得的方程可以用节点电压来表示。
然后，重新绘制电路，将 Kirchhoff 电压定律应用于超节点。
沿顺时针方向绕着包含超级节点的循环旋转，得到一个约束方程。
现在可以求解得到的三个方程来确定节点电压。

使用电压源来进行节点分析

节点分析是电气工程中一种非常有效的方法，通常用来简化复杂电路的分析，其中包括具有独立电压源的电路。它的优势在于采用系统化方法将电路分解为可管理的元件，从而使得工程师能够更容易的理解和解决问题。 假设有一个含有四个电阻器和两个电压源的电路，如图1所示。其中一个电压源会连接在非参考节点和参考节点之间。在这种电路中，非参考节点处的电压可以直接等于源极的电压。可以通过这种方式来减少未知数所带来的简化问题。 <img alt="Figure1" src="/files/ftp_upload/15048/15048_PT_Figure_1.svg" style="text-align: center; height: 140px;"> 另一个电压源则是连接在两个非参考节点之间。这种电路形成了所谓的超级节点或广义节点。其中的超级节点是节点分析中一个独特的概念，这有助于用来处理电压源连接在非参考节点之间的情况。 分析具有超级节点的电路需要应用基尔霍夫电流定律 (KCL) 和基尔霍夫电压定律 (KVL)。首先，基尔霍夫电流定律应用于超级节点。该定律指出，进入节点的电流总和等于离开节点的电流总和。通过考虑通过超级节点内每个元件的电流，可以获得一个方程并根据节点电压编写方程。 接下来，为了能够应用基尔霍夫电压定律，需要重新绘制电路来突出包含超级节点的循环。基尔霍夫电压定律指出了位于网络中从任何闭环或网格中的电动势总和等于该环路中电势降的总和。沿顺时针方向能够绕这个环路给出约束方程。 通过这些步骤，最终可以得到三个方程，它们能够用来代表电路的行为。并且可以同时求解这些方程来确定其中的节点电压。

节点分析可以有效地简化对具有相关或独立电压源的电路的分析。
考虑一个带有四个电阻器的电路 ...

Education

教育

JoVE Core

Electrical Engineering

电气工程

Unit 1

第一单元

DC Circuit Analysis

直流电路分析

KEY TERMS AND CONCEPTS

关键术语与概念

Nodal Analysis with Voltage Sources

supernode equations in nodal analysis

Nodal analysis uses node voltages and Kirchhoff’s laws to solve circuits with voltage sources. It is a systematic method for breaking a complex circuit into smaller parts that are easier to analyze. In this example, the circuit includes four resistors and two voltage sources.

One voltage source is connected between a non-reference node and the reference node. In that case, the non-reference node voltage can be written directly as the source voltage. This removes one unknown and makes the circuit easier to solve.

The other voltage source is connected between two non-reference nodes. That connection creates a supernode, also called a generalized node. A supernode is a special case in nodal analysis that helps when a voltage source sits between two nodes that are not the reference node.

To analyze the supernode, Kirchhoff’s Current Law (KCL) is used first. KCL says the total current entering a node equals the total current leaving it. The currents through the elements in the supernode are written in terms of the node voltages to form one equation.

Next, Kirchhoff’s Voltage Law (KVL) is applied. The circuit is redrawn to show the loop that includes the supernode, and the loop is traced in a clockwise direction. KVL states that the sum of the electromotive forces in a closed loop equals the sum of the voltage drops in that loop, which gives a second constraint equation.

These steps produce three equations for the circuit. The equations can then be solved together to find the node voltages. This approach shows how nodal analysis handles voltage sources connected to both the reference node and other nodes.

Supernode Equations in Nodal Analysis

nodal analysis

Using Node Voltages in Circuit Analysis

Nodal analysis uses node voltages to simplify circuit analysis. In this method, the voltage at each node becomes the main variable. Once those voltages are known, they can be used to find other values, such as the current through specific circuit parts. The process begins by choosing a reference node, also called a datum node. This node is selected for convenience and assigned a voltage of zero. The other nodes, called non-reference nodes, are then measured relative to that point. In the...

nodal analysis with voltage sources

Nodal analysis uses node voltages and Kirchhoff’s laws to solve circuits with voltage sources. It is a systematic method for breaking a complex circuit into smaller parts that are easier to analyze. In this example, the circuit includes four resistors and two voltage sources. One voltage source is connected between a non-reference node and the reference node. In that case, the non-reference node voltage can be written directly as the source voltage. This removes one unknown and makes the...

mesh analysis

Mesh Currents for Circuit Analysis

Mesh currents give students a simpler way to analyze planar circuits. In mesh analysis, the unknowns are currents, not voltages. The method uses Kirchhoff's voltage law, or KVL, to build the equations needed to solve the circuit. A mesh is a closed loop in a circuit that does not contain any smaller loops inside it. Each independent mesh is assigned a mesh current, and this current is usually drawn in the clockwise direction. These mesh currents are used as the main circuit variables during...

mesh analysis with current sources

Current Sources in Mesh Circuit Analysis

Current sources make mesh circuit analysis easier because they can reduce the number of equations needed. This applies to both independent and dependent current sources. The method depends on where the current source is placed in the circuit. When a current source appears in only one mesh, the setup is simple. Assign mesh currents as usual, but leave out the mesh that contains the current source from the equation process. Then apply Kirchhoff's voltage law, or KVL, to the remaining mesh to get...

source transformation

Circuit Source Equivalents

Circuit source equivalents make it easier to simplify electrical circuits in circuit analysis. A source transformation replaces a voltage source in series with a resistor by a current source in parallel with a resistor, or it replaces a current source in parallel with a resistor by a voltage source in series with a resistor. The key idea is that the equivalent resistance at the circuit terminals stays the same when the original sources are turned off. When making the change, the current source...

linear circuits

Circuit Linearity and Resistor Behavior

Circuit linearity describes how a circuit responds when its input changes. A linear circuit has an output that is directly proportional to its input. This behavior follows two rules: homogeneity and additivity. Homogeneity means that if the input, or excitation, is multiplied by a constant factor, the response is multiplied by the same factor. For example, if the current is increased by a constant k, the voltage also increases by k times. Additivity means that the response to a sum of inputs...

superposition theorem

Analyzing Circuits with Superposition

Superposition is a circuit analysis method for linear circuits with more than one independent source. It lets you find the voltage across or current through an element by adding the separate effects of each source acting alone. To use superposition, keep one independent source active and turn off the others. A voltage source is replaced by a short circuit, and a current source is replaced by an open circuit. Then calculate the output from the single active source. Repeat the process for each...

thevinin's theorem

Thevenin Circuit Equivalents

Thevenin circuit equivalents simplify linear two-terminal circuits by replacing the fixed part of a network with one equivalent source and one resistor. This method is useful when a circuit has a fixed section and a load that can change. A household electrical outlet is a familiar example, because different appliances can be plugged in or removed. Each change in load can require a new circuit analysis, so an equivalent circuit makes the work easier. Thevenin's theorem states that a linear...

norton's theorem

Norton Equivalent Circuit in DC Analysis

Norton equivalent circuit in DC analysis shows how a linear two-terminal circuit can be replaced by a simpler network. The replacement uses a current source, called I_N, in parallel with a resistor, called R_N. I_N is the short-circuit current through the terminals, and R_N is the input or equivalent resistance seen at the terminals when the independent sources are turned off. To find Norton's resistance, all independent sources in the circuit are set to zero. The resistance measured at the...

maximum power transfer

Load Matching in Thevenin Circuits

Load matching in Thevenin circuits helps a source deliver the most power to a connected load. This matters in engineering fields such as telecommunications, where power delivery must be optimized. Even then, internal losses can be significant and may equal or exceed the power sent to the load. The Thevenin equivalent circuit is a useful way to study this situation. It replaces the full linear circuit with a simpler source and resistance while keeping the load in place. In this setup, the load...

design example: strain gauge bridge or wheatstone bridge

design-example-strain-gauge-bridge-or-wheatstone-bridge

Wheatstone Bridge Output for Strain Gauge Design

A strain gauge and Wheatstone bridge work together to turn mechanical strain into an electrical signal. In engineering, this setup is often used to measure force or pressure. Each part of the bridge has a resistance that changes slightly when strain is applied. The main goal is to turn a very small voltage output into a larger, easier-to-read signal. A voltmeter can then measure that output more clearly. To do this, an engineer designs the strain gauge circuit and figures out how much...

key terms and concepts

Learn how nodal analysis uses supernodes, KCL, and KVL to solve circuits with voltage sources and find unknown node voltages.

Supernode Equations in Nodal Analysis | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

Supernode Equations in Nodal Analysis

Description

Transcript

Tags