Name: ac waveform basics and phase
Uploaded: 2024-04-11T12:48:48.000Z
Duration: 1 min 18 s
Channel: JoVE

K12 Standards

new-jersey-student-learning-standards-for-science

New Jersey Student Learning Standards for Science

High School

Physical Science

waves-and-their-applications-in-technologies-for-information-transfer

Waves and Their Applications in Technologies for Information Transfer

HS-PS4-2

Sinusoidal Sources

直流电是指单向电流，而交流电是指周期性反转方向的电流。
交流电对于电力传输和分配至关重要。
家庭电源使用正弦电源供电。这些源产生的电压随时间呈正弦变化。
在数学上，它由一个谐波函数表示，称为正弦曲线，该函数由其幅度、角频率和相位定义。
该函数的变化每 T 秒重复一次，一个完整周期的持续时间称为周期。它与角频率有关。
每秒的周期数就是频率。
考虑两个频率相同的正弦曲线。如果一个正弦曲线比另一个正弦曲线更早达到其最大值和最小值，则第一个正弦曲线领先于第二个正弦曲线。
然后说两个正弦曲线异相，它们之间的偏移称为相位差。
如果两个正弦曲线同时达到它们的最大值和最小值，则它们是同相的，因此相位差为零。

正弦波源

直流电 (DC) 是指沿单一方向流动、保持恒定极性的电流。这与交流电 (AC) 形成了鲜明的对比，交流电能够周期性地改变其方向和大小。由于其具有高效的长距离传输能力，因此交流电能够成为现代输配电系统的支柱。 在家庭中，电源能够使用正弦电源来提供电力。这些源能够产生随时间呈正弦变化的电压。换句话说，电压能够以平滑的波状模式在最大值和最小值之间产生振荡。 在数学上，这种变化由称为正弦曲线的调和函数来进行表示。正弦曲线通常由三个主要的参数来进行定义：振幅（峰值）、角频率（振荡速率）和相位（相对于参考点的位置）。 正弦波形会每相隔 T 秒重复一次该模式，其中的 T 称为函数的周期。周期与角频率则会成反比，以此来代表波形中一个完整周期的持续时间。 另一方面，正弦频率能够定义为每秒所发生的周期数。它是周期的倒数，通常以赫兹 (Hz) 为单位来进行测量。 如果要理解相位的概念，则需要思考两个具有相同频率的正弦曲线。如果一个正弦曲线早于另一个正弦曲线并且达到其最大值和最小值，则称第一个正弦曲线能够“领先”于第二个正弦曲线。在这种情况下，两个正弦曲线是异相的，它们之间的偏移称为相位差。 相反，如果两个正弦曲线能够同时达到其最大值和最小值，则认为它们是同相的。这意味着它们的相位差为零。 了解这些与交流电相关的基本概念对于从设计电子电路到分析电源系统的各种应用是至关重要的。交流电的原理是我们日常生活中许多技术的基础，其中包括家用电器、电信系统和发电设施。

直流电是指单向电流，而交流电是指周期性反转方向的电流。
交替。。。

Education

教育

JoVE Core

Electrical Engineering

电气工程

Unit 1

第一单元

AC Circuit Analysis

交流电路分析

KEY TERMS AND CONCEPTS

关键术语与概念

ac waveform basics and phase

Alternating current, or AC, changes direction and magnitude over time, unlike direct current, or DC, which flows in one direction with constant polarity. AC is the main form of electricity used for modern power transmission and distribution because it can travel long distances efficiently. In homes, power supplies use sinusoidal sources to deliver electricity.

A sinusoidal source creates a voltage that rises and falls in a smooth wave-like pattern. This waveform is called a sinusoid, which is a harmonic function. The shape of the wave is described by three key parts: amplitude, angular frequency, and phase. Amplitude is the peak value. Angular frequency tells how fast the wave oscillates. Phase shows the wave’s position compared with a reference point.

A sinusoid repeats after a time called the period, or T. The period is the time for one complete cycle of the waveform. It is inversely related to angular frequency. Frequency is the number of cycles per second, and it is the reciprocal of the period. Frequency is measured in Hertz, or Hz.

Phase helps compare two sinusoids with the same frequency. If one wave reaches its maxima and minima earlier than the other, it leads the second wave. The waves are then out of phase, and the shift between them is called the phase difference. If both waves reach their maxima and minima at the same time, they are in phase. In that case, the phase difference is zero.

Understanding AC, sinusoidal sources, and phase is important in many settings. These ideas are used in electronic circuit design and in power system analysis. They also support technologies that shape daily life, including household appliances, telecommunications systems, and power generation facilities.

AC Waveform Basics and Phase

sinusoidal sources

Alternating current, or AC, changes direction and magnitude over time, unlike direct current, or DC, which flows in one direction with constant polarity. AC is the main form of electricity used for modern power transmission and distribution because it can travel long distances efficiently. In homes, power supplies use sinusoidal sources to deliver electricity. A sinusoidal source creates a voltage that rises and falls in a smooth wave-like pattern. This waveform is called a sinusoid, which is...

graphical and analytic representation of sinusoids

graphical-and-analytic-representation-of-sinusoids

Measuring Sinusoid Phase on an Oscilloscope

Measuring sinusoid phase on an oscilloscope helps compare two sinusoidal voltages with the same amplitude and period. An oscilloscope is an instrument used to display and analyze waveforms. The process starts by reading the peak-to-peak value, which is twice the amplitude of the sinusoid. This shows the maximum voltage swing of the waveform. Next, the period and angular frequency are measured. The period is the time for one complete cycle. Angular frequency, often written as omega, is the rate...

phasors

Phasors for AC Circuit Analysis

Phasors are a mathematical tool for analyzing alternating current, or AC, circuits. They represent sinusoids with complex numbers. The phasor magnitude matches the sinusoid amplitude, and the phasor angle shows the phase measured from the positive x-axis. Phasors make AC circuit analysis simpler by removing time from the current and voltage expressions. That lets an AC circuit be treated like its equivalent direct current, or DC, form for calculations. Phasors can also be written in...

phasor arithmetics

Phasor Rules for AC Circuit Analysis

Phasor rules make AC circuit analysis easier by linking sinusoids to their matching phasors. A phasor is a complex-number form of a sinusoidal signal. This connection helps explain how alternating current changes with time. Differentiation and integration work in both the time domain and the phasor domain. If you take the derivative of a sinusoid in time, its phasor is multiplied by jω, where j is the imaginary unit and ω is the angular frequency. If you integrate a sinusoid in time, its...

phasor relationships for circuit elements

phasor-relationships-for-circuit-elements

AC Circuit Phasors: Resistor, Inductor, Capacitor

AC circuit phasors help show how voltage and current behave for resistors, inductors, and capacitors. Phasor representation moves these relationships from the time domain to the frequency domain, which makes AC circuit analysis easier. For a resistor, Ohm's law still applies. The voltage across the resistor and the current through it stay in phase, so their phasors point in the same direction. An inductor works differently because its voltage depends on the rate of change of current. The...

kirchoff's laws using phasors

AC Circuit Rules with Phasor Diagrams

AC circuit analysis uses Kirchhoff's voltage law and Kirchhoff's current law with phasors. In household wiring, AC power from a distribution panel is sent to appliances connected in parallel. These rules help describe how voltage and current behave in sinusoidal steady state. Kirchhoff's voltage law, or KVL, says that the sum of phasor voltages around a closed loop in an AC circuit is zero. The voltages can first be written in the time domain and then changed into phasor form. In phasor...

impedances and admittance

AC Circuit Response: Impedance and Admittance

AC circuit response changes with frequency, and impedance describes how resistors, inductors, and capacitors affect sinusoidal current flow. In phasor form, voltage and current are used to show this behavior in a clear way. Impedance is a key idea in AC circuit analysis because it measures opposition to current in an alternating circuit. These components behave differently in AC than in DC. In DC circuits, inductors act like short circuits and capacitors act like open circuits. In AC circuits,...

impedance combination

Series and Parallel Impedance Rules

Impedance in series and parallel circuits follows the same rules used for resistors. A string of Christmas lights is a simple example. Each bulb represents one impedance element. In a series connection, the current stays the same through every component. This series behavior matches Kirchhoff’s Voltage Law, or KVL. The total impedance in the circuit is the sum of the individual impedances. The source voltage is then divided among the components based on their values. This is the voltage...

node analysis for ac circuits

AC Circuit Node Method in an Angioplasty Model

AC circuit node analysis is used to study an angioplasty system with a catheter turbine. The system helps remove plaque deposits from coronary arteries. Its electrical model is similar to a dual-node RLC circuit driven by a current-controlled voltage source. The analysis begins by collecting the input source voltage, inductance, and capacitance values. These measurements are used to find the driving voltage for the catheter shaft. The circuit is then viewed in the frequency domain, where...

mesh analysis for ac circuits

Impedance Matching with Mesh Currents

Impedance matching in radio communication uses resistor, capacitor, and inductor circuits to help signals move efficiently between a transmitter and a receiver. The circuit must balance the input and output signals before the current in the capacitor can be found. This makes the problem a good example of AC circuit analysis for high school students. The first step is to identify the input voltage and the output signal. The angular frequency is then taken from the time-domain form of the input...

source transformation for ac circuits

AC Source Conversion in Circuit Analysis

AC source conversion is a circuit analysis method used in the frequency domain. It changes a voltage source in series with an impedance into a current source in parallel with the same impedance, or it converts a current source back into a voltage source. The source values must keep the correct relationship during each change. This method helps solve for an unknown voltage in a circuit that includes a current source and components such as resistors, capacitors, and inductors. Each of these...

th&#233venin equivalent circuits

Finding Voltage and Impedance in Circuit A

The household power distribution system can be simplified with Thevenin's theorem. In this system, distribution lines and transformers form the main network. Electrical appliances can be treated as load impedance, which makes the circuit easier to analyze. An AC circuit can be split into two parts, circuit A and circuit B, with a single pair of terminals between them. Circuit A can then be replaced by its Thevenin equivalent circuit. That equivalent has a voltage source in series with an...

norton equivalent circuits

Norton Current in AC Circuit Analysis

Norton’s theorem helps simplify complex AC circuits by replacing a two-terminal linear network with a smaller equivalent circuit. That equivalent circuit uses an impedance in parallel with a constant current source. The method lets students break one complicated circuit into two parts and analyze them more easily. To build the Norton equivalent, the source is replaced by its internal impedance. The result is the Norton impedance, which is the same as the Thévenin impedance. This parallel...

superposition theorem for ac circuits

Analyzing Mixed-Frequency Linear Circuits

Analyzing mixed-frequency linear circuits starts with the principle of superposition. In a linear circuit, the total output from several inputs is the sum of the outputs from each input acting alone. Here, the inputs are the voltages from independent voltage sources and the currents from independent current sources. When one source is kept active, every other independent source is set to zero. A 0-V voltage source becomes a short circuit, and a 0-A current source becomes an open circuit. This...

op amp ac circuits

Analyzing an Op Amp Audio Filter

An op amp audio filter shapes an amplified sound signal by strongly reducing the lower-frequency parts. In this circuit, the focus is on a basic filter setup used after an amplifier in an audio system. The filter uses an operational amplifier in an inverting arrangement with resistors R1 and R2 and a capacitor C1. The analysis starts with a known input signal and asks for the output signal. To solve it, the capacitor impedance is found first. That requires the angular frequency from the...

design example: capacitance multiplier circuit

design-example-capacitance-multiplier-circuit

Capacitance Multiplier Circuit for Larger Capacitance

A capacitance multiplier circuit creates a larger effective capacitance from a small physical capacitor. In integrated circuit technology, this approach is useful when a small capacitor is not enough. The circuit can multiply capacitance by as much as 1000, so a 10-pF capacitor can act like a 100-nF capacitor. The design uses two op-amps. The first op-amp works as a voltage follower, which helps isolate the generated capacitance from the loading caused by the second stage. The second op-amp...

key terms and concepts

Learn how AC sinusoidal sources work, including amplitude, frequency, period, and phase, plus why phase difference matters in power and circuits.

AC Waveform Basics and Phase | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

Travelling Waves

A wave is a disturbance that propagates from its source, repeating itself periodically, and is typically associated with simple harmonic motion. ...

Wave Parameters

The simplest mechanical waves are associated with simple harmonic motion and repeat themselves for several cycles. These simple harmonic waves can be ...

Equations of Wave Motion

Mathematically, the motion of a wave can be studied using a wavefunction. Consider a string oscillating up and down in simple harmonic motion, having a ...

Graphing the Wave Function

Consider the wave equation for a sinusoidal wave moving in the positive x-direction. The wave equation is a function of both position and time. From the ...

/files/media/science-education/science-education-thumbs/14721.jpg

Velocity and Acceleration of a Wave

A wave propagates through a medium with a constant speed, known as a wave velocity. It is different from the speed of the particles of the medium, which ...

Speed of a Transverse Wave

The speed of a wave depends on the characteristics of the medium. For example, in the case of a guitar, the strings vibrate to produce the sound. The ...

/files/media/science-education/science-education-thumbs/14722.jpg

problem-solving-tuning-of-a-guitar-string

Problem-Solving: Tuning of a Guitar String

In the case of stringed instruments like the guitar, the elastic property that determines the speed of the sound produced is its linear mass density or ...

/files/media/science-education/science-education-thumbs/14744.jpg

Kinetic and Potential Energy of a Wave

All forms of waves carry energy; this is directly visualized in nature. For instance, the waves of earthquakes are so intense that they can shake huge ...

Energy and Power of a Wave

The total energy associated with a wavelength is the sum of the potential energy and the kinetic energy. The average rate of energy transfer associated ...

Interference and Superposition of Waves

When two waves of the same nature occur in the same region simultaneously, they result in interference. Interference of waves implies that the net effect ...

Reflection of Waves

When a wave travels from one medium to another, it gets reflected at the boundary of the second medium. A common example of this is when a person yells at ...

Propagation of Waves

When a wave propagates from one medium to another, part of it may get reflected in the first medium, and part of it may get transmitted to the second ...

Standing Waves

Sometimes waves do not seem to move; rather, they just vibrate in place. Unmoving waves can be seen on the surface of a glass of milk kept in a ...

/files/media/science-education/science-education-thumbs/12783.jpg

Modes of Standing Waves - I

A close look at earthquakes provides evidence for the conditions appropriate for resonance, standing waves, and constructive and destructive interference. ...

/files/media/science-education/science-education-thumbs/12784.jpg

Modes of Standing Waves: II

The starting point for expressing the modes of standing waves is understanding the boundary conditions that the waves must follow. The boundary conditions ...

/files/media/science-education/science-education-thumbs/14723.jpg

Use mathematical representations to support a claim regarding relationships among the frequency, wavelength, and speed of waves traveling in various media. 

Clarification statement: Examples of data could include electromagnetic radiation traveling in a vacuum and glass, sound waves traveling through air and water, and seismic waves traveling through the earth. 

Assessment Boundary: Assessment is limited to algebraic relationships and describing those relationships qualitatively.

HS-PS4-1

Speed of Sound in Gases

The speed of sound in a gaseous medium depends on various factors. Since gases constitute molecules that are free to move, they are highly compressible. ...

Direct current refers to unidirectional current, whereas alternating current refers to current that reverses its direction periodically.
Alternating ...

Signal and System

Signals are sets of data or information.
One-dimensional signals include single-variable functions, such as the variations in air pressure over time in ...

reconstruction-of-signal-using-interpolation

Reconstruction of Signal using Interpolation

Consider a continuous signal and its sampled counterpart with a sampling period T.
Applying a zero-order hold to the sampled signal results in a piecewise ...

Classification of Signals

Signals are categorized as Continuous-time or discrete-time, Periodic or aperiodic, Analog or digital, and Causal or noncausal.
A continuous-time signal ...

Evaluate questions about the advantages of using a digital transmission and storage of information. 

Clarification statement: Examples of advantages could include that digital information is stable because it can be stored reliably in computer memory, transferred easily, and copied and shared rapidly. Disadvantages could include issues of easy deletion, security, and theft.

dual-nature-of-electromagnetic-em-radiation

Dual Nature of Electromagnetic (EM) Radiation

Electromagnetic (EM) radiation consists of electric and magnetic field components oscillating in planes perpendicular to each other and mutually ...

Electromagnetic Waves in Matter

Electromagnetic waves can travel in the vacuum as well as in matter. For example light, which is an electromagnetic wave, can travel through air, water, ...

Electromagnetic Waves

James Clerk Maxwell formulated a single theory combining all the electric and magnetic effects scientists knew during that time, calling the phenomena his ...

Generating Electromagnetic Radiations

The German physicist Heinrich Hertz (1857&#8211;1894) was the first to generate and detect certain types of electromagnetic waves in the laboratory. ...

Evaluate the claims, evidence, and reasoning behind the idea that electromagnetic radiation can be described either by a wave model or a particle model, and that for some situations one model is more useful than the other. 

Clarification statement: Emphasis is on how the experimental evidence supports the claim and how a theory is generally modified in light of new evidence. Examples of a phenomenon could include resonance, interference, diffraction, and photoelectric effect. 

Assessment Boundary: Assessment does not include using quantum theory.

HS-PS4-3

The Electromagnetic Spectrum

The electromagnetic spectrum consists of all the types of electromagnetic radiation arranged according to their frequency and wavelength. Each of the ...

Biological Effects of Radiation

All radioactive nuclides emit high-energy particles or electromagnetic waves. When this radiation encounters living cells, it can cause heating, break ...

Evaluate the validity and reliability of claims in published materials of the effects that different frequencies of electromagnetic radiation have when absorbed by matter. 

Clarification statement: Emphasis is on the idea that photons associated with different frequencies of light have different energies, and the damage to living tissue from electromagnetic radiation depends on the energy of the radiation. Examples of published materials could include trade books, magazines, web resources, videos, and other passages that may reflect bias. 

Assessment Boundary: Assessment is limited to qualitative descriptions.

HS-PS4-4

Control Systems

Control systems influence many applications, from space shuttles to automated manufacturing. They exist naturally, such as our body&#39;s blood sugar ...

Electromagnetic waves are categorized according to their wavelengths and frequencies, giving the electromagnetic spectrum. These waves are classified as ...

Electromagnetic Wave Equation

Maxwell&#39;s equations for electromagnetic fields are related to source charges, either static or moving. These fields act on a test charge, whose ...

Plane Electromagnetic Waves I

The existence of combined electric and magnetic fields that propagate through space as electromagnetic (EM) waves is the most significant prediction of ...

Plane Electromagnetic Waves II

Consider a plane wavefront traveling in position x-direction with a constant speed. This wavefront can be utilized to obtain the relationship between ...

propagation-speed-of-electromagnetic-waves

Propagation Speed of Electromagnetic Waves

Electromagnetic waves are consistent with Ampere&#39;s law. Assuming there is no conduction current Ampere&#39;s law is given as:


Consider a plane ...

Energy Carried By Electromagnetic Waves

Anyone who has used a microwave oven knows there is energy in electromagnetic waves. Sometimes, this energy is obvious, such as in the summer sun&#39;s ...

Intensity Of Electromagnetic Waves

The energy transport per unit area per unit time, or the Poynting vector, gives the energy flux of an electromagnetic wave at any specific time. For a ...

Standing Electromagnetic Waves

Electromagnetic waves can be reflected; the surface of a conductor or a dielectric can act as a reflector. As electric and magnetic fields obey the ...

Standing Waves in a Cavity

A household microwave and lasers are examples of standing electromagnetic waves in a cavity. When two conducting metal plates are placed parallel at the ...

Communicate technical information about how some technological devices use the principles of wave behavior and wave interactions with matter to transmit and capture information and energy. 

Clarification statement: Examples could include solar cells capturing light and converting it to electricity; medical imaging; and communications technology. 

Assessment Boundary: Assessments are limited to qualitative information. Assessments do not include band theory.

HS-PS4-5

AC Waveform Basics and Phase

Description

Transcript

Tags

More videos by Standards