30.4
Gleichstromgenerator
Ein Wechselstromgenerator wandelt mechanische Energie in elektrische Energie um, die sinusförmig variiert und somit zu Wechselstrom führt. Ein Gleichs…
Ein Gleichstromgenerator wandelt mechanische Energie in elektrische Gleichstrom um. Der Grundaufbau des Gleichstromgenerators ähnelt dem der einfachen Lichtmaschine, nur dass die beiden Schleifringe durch einen einzigen Spaltring ersetzt werden.
Wenn sich die leitende Schleife in einem gleichmäßigen Magnetfeld dreht, ändert sich der magnetische Fluss durch die Schleife sinusförmig, was zu induzierter EMK führt.
Dabei fungiert der Spaltring als Kommutator. Der Kommutator schaltet die Kontakte für jede halbe Umdrehung der Schleife und sorgt so für die gleiche Polarität der induzierten EMK.
Ähnlich wie bei einer Lichtmaschine ist die induzierte EMK Null, wenn der magnetische Fluss entweder maximal oder minimal ist.
Aufgrund des Kommutators ist die induzierte EMK jedoch nie negativ und hat ein Maximum, wenn der magnetische Fluss Null ist.
Die Größe der durchschnittlichen induzierten EMK wird geschätzt, indem der sinusförmige Term aus dem einfachen Generator durch seinen Durchschnittswert ersetzt wird.
Die Größe der induzierten EMK ist proportional zur Winkelgeschwindigkeit für das gegebene Magnetfeld und die Fläche der Schleife.
View the full transcript and gain access to JoVE Core videos
Q1: How does a DC generator differ from an alternator?
A DC generator converts mechanical energy into DC electrical energy with constant polarity, while an alternator produces AC current that varies sinusoidally. The key difference is that a DC generator uses a split ring commutator instead of slip rings. The commutator switches contacts for each half rotation, ensuring the induced emf always maintains the same polarity rather than alternating between positive and negative values.
Q2: What role does the commutator play in a DC generator?
The commutator is a split ring that functions as a periodic rotary switch, changing contacts with the brushes for each half rotation of the conducting loop. This switching ensures that the induced emf always has the same polarity. Without the commutator, the output would alternate between positive and negative values like an alternator, but the commutator rectifies the signal into unidirectional DC pulses.
Q3: When is the induced emf maximum in a DC generator?
The induced emf is maximum when the magnetic flux through the conducting loop is zero. This occurs when the loop rotates through the vertical position. Conversely, the induced emf is minimum when the magnetic flux is either maximum or minimum. The commutator ensures these minimum points appear as zero values rather than negative peaks, maintaining constant polarity throughout the rotation cycle.
Q4: How does magnetic flux change affect induced emf in a DC generator?
As the conducting loop rotates in a uniform magnetic field, the magnetic flux through it changes sinusoidally. This changing magnetic flux induces an emf according to Faraday's law of induction. The magnitude of the induced emf depends on how rapidly the flux changes, which is directly proportional to the angular velocity of the loop rotation and the strength of the magnetic field.
Q5: What factors determine the magnitude of induced emf in a DC generator?
The magnitude of induced emf is proportional to three factors: the strength of the applied uniform magnetic field, the area of the conducting loop, and the angular velocity of rotation. Increasing any of these parameters increases the induced emf. The average induced emf is calculated by replacing the sinusoidal variation with its average value, providing a measure of the generator's output voltage.
Q6: How does the conducting loop connect to an external circuit in a DC generator?
The conducting loop connects to the external circuit through a commutator and a pair of brushes. As the loop rotates and the commutator switches contacts, the brushes maintain electrical connection with the external circuit. This arrangement ensures that current flows in one direction through the external load, delivering DC power despite the alternating nature of the induced emf within the rotating loop.
Q7: Why does a DC generator output have constant polarity?
The split ring commutator switches the contact points with the brushes every half rotation, reversing the internal connections at the same moment the induced emf would naturally reverse. This synchronization ensures the output terminals always receive the same polarity, converting the sinusoidal induced emf into unidirectional DC pulses that fluctuate between zero and maximum rather than oscillating between positive and negative values.