11.10
Brückengleichrichter
Der Brückengleichrichter ist in der Elektronik unverzichtbar, um Wechselstrom (AC) effizient in Gleichstrom (DC) umzuwandeln. Dieser Gleichrichter bes…
Der Brückengleichrichter, der für die Umwandlung von Wechselstrom in Gleichstrom unerlässlich ist, besteht aus vier Dioden, die in einer Brückenkonfiguration angeordnet sind.
Diese Anordnung ermöglicht es, sowohl die positive als auch die negative Hälfte der Wellenform zu korrigieren.
Während der positiven Halbzyklen der Eingangsspannung leitet der Brückengleichrichter Strom durch die Dioden D1 und D2 und den Widerstand R, während die Dioden D3 und D4 in Sperrrichtung vorgespannt sind.
Umgekehrt ist bei negativen Halbzyklen die Sekundärspannung negativ, und der Strom fließt durch die Dioden D3 und D4 und den Widerstand R, wobei die Dioden D1 und D2 in Sperrrichtung vorgespannt sind.
Trotz der wechselnden Zyklen bleibt die Richtung des Stromflusses konstant, was zu einer gleichbleibend positiv pulsierenden DC-Ausgangsspannung führt.
Die inverse Spitzenspannung wird während positiver Halbzyklen ermittelt und beträgt etwa die Hälfte des Wertes für einen Vollwellengleichrichter mit einem Transformator mit Mittenabgriff.
Der Brückengleichrichter benötigt weniger Umdrehungen für die Sekundärwicklung des Transformators, wodurch er effizienter und kompakter wird.
Der Wirkungsgrad des Brückengleichrichters kann durch die Verwendung von Schottky-Dioden oder durch den Einbau eines Kondensatorfilters gesteigert werden, der Verluste reduziert und die Qualität des DC-Ausgangs verbessert.
View the full transcript and gain access to JoVE Core videos
Q1: How does a bridge rectifier convert AC to DC?
A bridge rectifier uses four diodes arranged in a bridge configuration to convert alternating current to direct current. During positive half-cycles, diodes D1 and D2 conduct while D3 and D4 are reverse-biased. During negative half-cycles, D3 and D4 conduct while D1 and D2 are reverse-biased. This alternating conduction pattern ensures current flows through the load resistor in a single direction, producing a consistently positive pulsating DC output.
Q2: What is the advantage of a bridge rectifier over a full wave rectifier with a center-tapped transformer?
The bridge rectifier requires fewer turns on the transformer's secondary winding compared to a full wave rectifier, making it more efficient and compact. Additionally, the peak inverse voltage in a bridge rectifier is approximately half that of a center-tapped full wave rectifier, reducing stress on the diodes and enabling more cost-effective circuit design.
Q3: Why are diodes reverse-biased during certain half-cycles in a bridge rectifier?
During each half-cycle, only two diodes conduct while the other two are reverse-biased to prevent current from flowing backward through the circuit. This selective conduction ensures unidirectional current flow through the load resistor. The reverse-biased diodes block current in the opposite direction, maintaining the consistent positive output voltage required for DC applications.
Q4: How can the output quality of a bridge rectifier be improved?
Bridge rectifier performance can be enhanced by using Schottky diodes, which have low forward voltage drops and fast recovery times, reducing losses. Adding a capacitor filter minimizes ripple in the output, producing higher-quality DC voltage. These improvements result in more stable and cleaner direct current suitable for sensitive electronic applications.
Q5: What is peak inverse voltage in a bridge rectifier?
Peak inverse voltage (PIV) is the maximum reverse voltage that appears across a diode when it is reverse-biased. In a bridge rectifier, the PIV is calculated as the source voltage minus the diode voltage. This value is approximately half that of a full wave center-tapped rectifier, making bridge rectifiers suitable for lower-voltage diode applications.
Q6: How does current flow through a bridge rectifier during positive and negative half-cycles?
During positive half-cycles, current flows through diodes D1 and D2 and the load resistor R, while diodes D3 and D4 are reverse-biased. During negative half-cycles, current flows through diodes D3 and D4 and resistor R, with D1 and D2 reverse-biased. Despite this alternating path, the current direction through the load remains constant, ensuring steady positive pulsating DC output.
Q7: Why is the bridge rectifier configuration more efficient than other rectifier types?
The bridge rectifier processes both positive and negative halves of the AC waveform using only four diodes and a standard transformer, eliminating the need for a center-tapped secondary winding. This simpler design reduces transformer complexity, lowers cost, and improves voltage regulation and output stability. The reduced component count and transformer turns requirement make bridge rectifiers the preferred choice for efficient AC-to-DC conversion.