Moisture Content
Moisture Content - Related Videos
06:16
Determination of Moisture Content in Soil
0 Views •
2023
Source: Laboratories of Dr. Ian Pepper and Dr. Charles Gerba - The University of Arizona Demonstrating Author: Bradley Schmitz Soils normally contain a finite amount of water, which can be expressed as the “soil moisture content.” This moisture exists within the pore spaces in between soil aggregates (inter-aggregate pore space) and within soil aggregates (intra-aggregate pore space) (Figure 1). Normally this pore space is occupied by air and/or water. If all the pores are occupied by air, the...
01:10
Moisture Content and Bulking of Aggregate
0 Views •
2024
The moisture content of aggregates is a crucial factor in construction, particularly in concrete mixing, as it influences the total water required in the mix. Moisture content represents the water coated on the exterior surface of the aggregate existing in a saturated and surface-dry condition. The total water content of a moist aggregate is the sum of its moisture content and water absorption. When aggregates are exposed to rain or sit in stockpiles, they absorb moisture, which must be...
08:52
Method to Produce Durable Pellets at Lower Energy Consumption Using High Moisture Corn Stover and a Corn Starch Binder in a Flat Die Pellet Mill
0 Views •
Cited by 50 •
2016
In this study, a protocol was developed to produce good quality pellets using a flat die pellet mill at reduced specific energy consumption testing high-moisture corn stover and a starch based binder. The results indicated that adding a corn starch binder improved the pellet durability, reduced percent fines and decreased specific energy consumption.
15:04
A Neuronal and Astrocyte Co-Culture Assay for High Content Analysis of Neurotoxicity
0 Views •
Cited by 46 •
2009
This article describes a novel protocol and reagent set designed for sensitive measurement of neurotoxic effects of compounds and treatments on co-cultures of neurons and astrocytes using high content analysis. Results demonstrate that high content analysis represents an exciting novel technology for neurotoxicity assessment.
07:04
Determination of the Glycogen Content in Cyanobacteria
0 Views •
Cited by 26 •
2017
Here, we present a reliable and easy assay to measure the glycogen content in cyanobacterial cells. The procedure entails precipitation, selectable depolymerization, and the detection of glucose residues. This method is suitable for both wildtype and genetically engineered strains and can facilitate the metabolic engineering of cyanobacteria.
FAQs
Using dry-solid mass as the reference separates the water quantity from the specimen’s final solid material quantity. This makes the result suitable for comparison between samples and allows percentage reporting to communicate the relationship compactly. The chosen reporting basis should be stated clearly whenever moisture measurements guide material selection, quality control, or construction decisions.
Drying conditions determine how completely water is removed before the final weighing. Insufficient time or an unsuitable temperature can leave residual water and alter the calculated value, while material composition can affect how the specimen responds to drying. Controlled, consistent conditions are therefore essential when comparing specimens or evaluating process performance.
Its effects depend on the material system. In soil, moisture content influences compaction and strength; in concrete, it affects behavior; and in timber, it contributes to dimensional stability. For powders and aggregates, it can influence flow or storage. Consequently, the same measurement supports different engineering interpretations rather than one universal performance judgment.
A typical determination begins by weighing the specimen before drying. The sample then undergoes controlled oven drying, or another validated water-removal method, until the relevant dry condition is reached. The dried specimen is weighed again, and the mass loss is compared with the dry mass. This calculation produces the reported moisture-content value.
The test requires consistent weighing, controlled water removal, and a clearly defined drying endpoint. Temperature and drying time must be managed because both can change the mass loss used in the calculation. Material composition also matters, so the selected oven procedure or alternative method should be validated for the specimen being examined.
Measurements support material selection, quality control, construction decisions, and process performance. For example, results can inform assessment of soil conditions related to compaction and strength, help evaluate concrete behavior, and identify moisture-related considerations for timber, powders, or aggregates. The practical value comes from connecting the measured condition with the material’s intended use.
The result provides a measurable condition that can be interpreted alongside the material’s engineering function. Soil measurements relate to compaction and strength, timber measurements to dimensional stability, and powder or aggregate measurements to flow and storage. Concrete results contribute to understanding its behavior. These links help engineers apply testing to quality control and construction choices.