Liquid Medication
Liquid Medication - Related Videos
10:43
Rapid and Low-cost Prototyping of Medical Devices Using 3D Printed Molds for Liquid Injection Molding
0 Views •
Cited by 34 •
2014
We have devised a method for low-cost and rapid prototyping of liquid elastomer rubber injection molded devices by using fused deposition modeling 3D printers for mold design and a modified desiccator as a liquid injection system.
11:11
Preparing and Administering Oral Tablet and Liquid Medications
0 Views •
2015
Source: Madeline Lassche, MSNEd, RN and Katie Baraki, MSN, RN, College of Nursing, University of Utah, UT Oral medications are the route most preferred by patients and are one of the most commonly used routes of medication administration by providers. Most oral preparations are taken by mouth, swallowed with fluid, and absorbed via the gastrointestinal tract. Oral medications are available in solid forms (e.g., tablets, capsules, caplets, and enteric-coated tablets) and liquid forms (e.g.,...
06:59
A Novel Approach for the Administration of Medications and Fluids in Emergency Scenarios and Settings
0 Views •
Cited by 5 •
2016
This study presents a novel device that offers an easy route to quickly provide medications and fluids in patients with limited or difficult IV access. This small-diameter device is placed in the distal third of the rectum, allowing for ongoing medication and fluids administration.
09:21
Efficiency of Liquid-liquid Extraction
0 Views •
2023
Source: Kerry M. Dooley and Michael G. Benton, Department of Chemical Engineering, Louisiana State University, Baton Rouge, LA Liquid-liquid extraction (LLE) is a separation technique used instead of distillation when either: (a) the relative volatilities of the compounds to be separated are very similar; (b) one or more of the mixture components are temperature sensitive even near ambient conditions; (c) the distillation would require a very low pressure or a very high distillate/feed...
13:38
Synthesis of Biocompatible Liquid Crystal Elastomer Foams as Cell Scaffolds for 3D Spatial Cell Cultures
0 Views •
Cited by 9 •
2017
This study presents a methodology to prepare 3D, biodegradable, foam-like cell scaffolds based on biocompatible side-chain liquid crystal elastomers (LCEs). Confocal microscopy experiments show that foam-like LCEs allow for cell attachment, proliferation, and the spontaneous alignment of C2C12s myoblasts.
FAQs
The distinction between a solution and a suspension affects administration. In a solution, the active ingredient is fully dissolved in the fluid vehicle. In a suspension, active-ingredient particles are distributed throughout that vehicle rather than dissolved. Recognizing which formulation is being used helps determine whether shaking is required before measuring a dose.
Excipients support more than flavor. Within a liquid medication, these inactive components can help maintain formulation stability, improve palatability, and support consistent dosing. Their functions matter clinically because a preparation must remain usable and acceptable while delivering the intended amount of active ingredient in the measured volume during treatment.
Shaking is relevant specifically to suspensions because their active ingredient is present as distributed particles rather than fully dissolved. Following the instruction to shake helps prepare the formulation as intended before a volume is measured. This step supports more consistent dosing, whereas a solution does not require particle redistribution.
An oral syringe or another appropriate measuring device provides a controlled way to measure the prescribed liquid volume. This is important because liquid medication doses are administered by volume, and inaccurate measurement can change the amount delivered. Using calibrated equipment therefore helps reduce dosing errors in clinical administration.
Liquid medication is particularly useful when a patient cannot easily swallow tablets or capsules. In clinical practice, this includes infants, older adults, and people with swallowing limitations. The fluid format can also permit dose adjustment by measured volume, allowing treatment to be adapted without relying on a solid dosage form.
When selecting or administering a liquid formulation, the key practical questions are whether the active ingredient is dissolved or suspended, whether shaking is directed, and which measuring device is appropriate. These details connect formulation design with bedside technique: identifying them helps clinicians deliver the intended volume and use the preparation consistently.