Name: how aggregate size affects bulk density
Uploaded: 2024-09-12T16:16:40.000Z
Duration: 1 min 22 s
Channel: JoVE

응집체의 벌크 밀도는 그 사이에 존재하는 공극 공간을 포함하여 단위 부피 내의 응집체의 질량을 나타냅니다. 일반적으로 입방 피트당 파운드로 표시됩니다.
조밀하게 압축된 응집체는 느슨하게 압축된 응집체에 비해 더 높은 벌크 밀도를 달성합니다.
크기가 다른 응집체를 압축할 때 더 작은 입자가 더 큰 입자 사이의 틈을 메우므로 비슷한 크기의 골재를 압축할 때보다 더 높은 벌크 밀도가 생성됩니다.
또한 골재의 모양도 벌크 밀도에 영향을 미칩니다. 둥근 골재는 각진 골재보다 공극이 적어 둥근 골재의 더 높은 부피 밀도에 기여합니다.
또한 골재 표면에 수분이 존재하면 인접한 골재가 밀집되어 압축이 방해됩니다.
공극 공간의 비율은 골재의 벌크 밀도, 골재의 포화 표면 건조 상태에서의 벌크 비중 및 물의 단위 질량을 사용하여 계산됩니다.
공극 공간의 양은 콘크리트 혼합물에서 거친 골재 사이의 틈을 메우는 데 필요한 모르타르의 부피를 나타냅니다.

골재의 부피 밀도

부피 밀도는 단위 부피를 채울 골재 입자의 질량을 의미합니다. 부피 밀도라는 개념은 골재 입자를 완전히 밀착시켜 공극을 모두 제거하는 것이 불가능하다는 점에서 유래되었습니다. 따라서 부피라는 용어는 골재와 공극을 모두 포함하는 부피를 말합니다. 이 측정값은 골재가 부피로 배치될 때 중요하며, 질량을 부피로 변환할 때 사용됩니다.

모래와 자갈과 같은 대부분의 천연 미네랄 골재는 일반적으로 1521.75 – 1601.85 kg/m^3 범위에 있으며, 이들은 단위 중량이 약 2402.77 kg/m^3 인 정상 중량의 콘크리트를 생산하는 데 사용됩니다. 부피 밀도가 1121.29 kg/m^3 미만인 골재는 경량으로 분류되며, 밀도가 3.68 m^3 를 초과하는 골재는 중량으로 간주됩니다.

골재 입자의 부피 밀도는 입자 크기 분포의 영향을 받습니다. 단일 크기의 골재는 제한된 정도로만 압축할 수 있지만, 더 작은 입자를 큰 입자 사이의 공극에 채워 넣으면 부피 밀도를 높일 수 있습니다. 잔골재와 굵은 골재의 혼합물의 최적 부피 밀도는 잔골재가 전체 골재 질량의 약 35~40%를 구성할 때 달성됩니다.

응집체의 벌크 밀도는 그 사이에 존재하는 공극 공간을 포함하여 단위 부피 내의 응집체의 질량을 나타냅니다. 그것은 일반적으로 ...

Education

교육

JoVE Core

Civil Engineering

토목공학

Unit 1

제1단원

Aggregates and Water

골재 및 용수

KEY TERMS AND CONCEPTS

주요 용어 및 개념

Bulk Density of Aggregate

how aggregate size affects bulk density

Bulk density describes the mass of aggregate that fills a unit volume, including the empty spaces between particles. Those void spaces remain because aggregate particles cannot be packed so tightly that every gap disappears. In practice, bulk refers to the total volume of both the particles and the spaces around them.

This measurement matters when aggregates are batched by volume. It also helps convert materials measured by mass into a volume-based quantity. Natural mineral aggregates such as sand and gravel usually have a bulk density of about 95 to 100 lb/ft 3, and they are commonly used to make normal-weight concrete with a unit weight of about 150 lb/ft 3.

Aggregates can also be grouped by bulk density. Materials below 70 lb/ft 3 are classified as lightweight. Materials above 130 ft 3 are considered heavyweight.

Particle size distribution changes bulk density. Aggregates made of one size can only be compacted to a limited degree. When smaller particles fit into the gaps between larger ones, the bulk density increases. The best bulk density in a mix of fine and coarse aggregates is reached when fine aggregates make up about 35 to 40 percent of the total aggregate mass.

How Aggregate Size Affects Bulk Density

unsoundness of aggregate due to volume change

unsoundness-of-aggregate-due-to-volume-change

Aggregate Durability in Freeze-Thaw Cycles

Aggregate durability can decline when volume changes damage the particles. Freezing and thawing, thermal change, and wetting and drying all place stress on aggregates. When unsound aggregates break down under these conditions, they can contribute to scaling, pop-outs, and cracking in concrete. Some aggregates are more vulnerable than others. Porous flints, cherts, and aggregates that contain clay minerals are especially prone to this kind of damage. Their internal structure can make them...

deleterious substances in aggregate

Testing Aggregate Impurities in Concrete

Aggregate impurities can lower the quality and durability of concrete. Organic matter, such as loam in sand, can interfere with cement hydration and weaken the bond between the aggregate and the cement paste. Organic impurities are often checked with a colorimetric test. In this test, the darkness of the solution after agitation shows the level of organic content. Clay and fine material can also coat aggregate particles and reduce the bond with the cement paste. The amount of clay and silt in...

sieve analysis and grading curves

Aggregate Size Testing with Sieve Grading

Aggregate size testing with sieve grading measures the particle size distribution of aggregate materials. It starts with a dried sample of aggregate that is weighed first. The sample is then sorted through a stack of square-opening sieves arranged from largest opening on top to smallest opening below. The sieve stack is shaken or vibrated so the particles move through the openings by size. After a set time, the material left on each sieve is weighed. That weight is then written as a percentage...

fineness modulus

Fineness Modulus from Sieve Analysis

Fineness modulus is a numerical index used to describe how coarse or fine aggregate particles are. For sand, it is found from sieve analysis using a standard set of ASTM sieves. The result helps show whether the sample is finer or more coarse. To calculate fineness modulus, first record the weight of aggregate retained on each sieve and in the pan at the bottom. Then find the cumulative weight retained on each sieve. Next, express each cumulative weight as a percentage of the total sample...

types of aggregate grading

Aggregate Grading for Strong Concrete Mixes

Aggregate grading describes the particle size distribution in a sample of aggregate. It is important for making a concrete mix that has enough strength, reasonable workability, and minimal segregation. The right grading also helps concrete stay economical. There are four main types of aggregate gradation: well-graded, uniformly graded, gap-graded, and open-graded. Each type has a different pattern on a gradation curve, which shows how particle sizes are spread across sieve sizes. These...

maximum size of aggregate

How Aggregate Size Affects Concrete Mix

Aggregate size affects how concrete is mixed, placed, and strengthened. The maximum size of aggregate is defined by the sieve aperture that retains 15 percent or more of the particles in the sample. This size choice helps determine the concrete’s water demand, workability, and final strength. Larger aggregate particles reduce the surface area that must be covered by cement paste. As a result, they can lower the water needed in the mix. When the desired workability and richness are kept, this...

quality of water

Water Standards for Concrete Mixing

Water standards for concrete mixing help control strength and durability. Potable water is usually preferred. Even so, it should not contain too much sodium or potassium, because these salts can weaken concrete integrity. Water quality is judged by impurities such as dissolved solids, chlorides, and sulfates. The pH value is ideally between 6 and 8. Slightly acidic natural water may still be acceptable if it does not contain harmful organic matter or algae. Limits for these impurities depend...

testing water quality

Water Tests for Concrete Performance

Water tests for concrete performance help determine whether an uncertain water source is safe to use in cement and mortar. The main checks compare the water against de-ionized or distilled water benchmarks. Engineers look at both setting time and the compressive strength of mortar made with the test water. Standards set clear limits for these results. ASTM C1602 requires setting times to stay within 90 minutes of the control. BS 3146:1980 allows a 30-minute change in initial setting, while BS...

aggregates classification

Aggregate Types by Size, Weight, and Source

Aggregate types are grouped by size, petrographic characteristics, weight, and source. These categories help describe how different aggregates are identified and used in concrete. Size is one of the most common ways to classify them. Based on particle size, aggregates are either coarse or fine. Coarse aggregates are particles that do not pass through ASTM sieve No. 4. Fine aggregates are the particles that do pass through that sieve. Petrographic classification looks at shared mineral features.

shape and texture of coarse aggregate

How Aggregate Form Changes Concrete

Aggregate form affects how concrete mixes, packs, and bonds. Coarse aggregate is classified by the sharpness or roundness of its edges and corners. The main shapes are rounded, angular, elongated, and flaky. These shapes help show how the particles will behave in concrete. Rounded aggregates are fully shaped by attrition, which means they have been worn down by rubbing and impact. River gravel and seashore gravel are common examples. Angular aggregates, such as crushed rock, have clear edges...

bonding and strength of aggregate

How Aggregate Shape Affects Concrete Bond

Aggregate shape and surface texture affect how well concrete holds together. Rough, angular aggregates usually bond more strongly with the cement matrix than smooth, rounded ones. This stronger adhesion can help produce high-strength concrete. Angular aggregates also have a larger surface area. That gives the cement paste more area to grip, which improves the bond. Bond quality is hard to measure directly, and there is no single test that is accepted everywhere. A broken concrete sample can...

toughness and hardness of aggregate

Testing Aggregate Impact and Abrasion

Aggregate toughness and hardness are important for concrete used on pavement surfaces and industrial floors that must carry heavy loads. Toughness means an aggregate can resist failure from impact. Hardness means it can resist wear.

specific gravity of aggregate

Aggregate Pore Effects on Specific Gravity

Aggregate specific gravity depends on the pores inside the material. These pores may be permeable or impermeable, so the same aggregate can be described in more than one way. For this reason, specific gravity is grouped into bulk or gross specific gravity, apparent specific gravity, and absolute specific gravity. Bulk or gross specific gravity uses the mass of aggregate in the saturated surface-dry state. It is compared with the total volume of the aggregate, including both the solids and the...

bulk density of aggregate

Bulk density describes the mass of aggregate that fills a unit volume, including the empty spaces between particles. Those void spaces remain because aggregate particles cannot be packed so tightly that every gap disappears. In practice, bulk refers to the total volume of both the particles and the spaces around them. This measurement matters when aggregates are batched by volume. It also helps convert materials measured by mass into a volume-based quantity. Natural mineral aggregates such as...

porosity and absorption of aggregate

Aggregate Pore States and Water Uptake

Aggregate contains pores of different sizes, and those pores may be sealed inside the particle or open to the surface. Open pores let water enter the aggregate. Because aggregate makes up about three-quarters of concrete by volume, its porosity strongly affects the porosity of the finished concrete. Aggregate can also be described by its moisture state. When water fills every pore, the material is saturated and surface-dry. If it sits in dry air, some water evaporates and the aggregate becomes...

moisture content and bulking of aggregate

moisture-content-and-bulking-of-aggregate

How Aggregate Moisture Affects Concrete Mixes

Aggregate moisture affects concrete mixing by changing how much water must be added to the batch. Moisture content is the water coating the outside of aggregate that is in a saturated and surface-dry state. The total water in moist aggregate includes both moisture content and water absorption. When aggregates sit in stockpiles or are exposed to rain, they can take in moisture. That extra water must be counted during concrete batching so the water-to-cement ratio stays correct. The moisture...

key terms and concepts

Learn how aggregate size distribution changes bulk density, why void spaces matter, and how sand and gravel are classified for normal, lightweight, and heavyweight concrete.

How Aggregate Size Affects Bulk Density | JoVE K12

JoVE Core Civil Engineering offers a foundational exploration of essential construction materials such as bricks, stones, steel, wood, and concrete, along with fluid mechanics topics like flow over immersed bodies, open channel flow, and dimensional modeling. It also covers key surveying concepts, including leveling, traverse adjustments, curve design, topographic mapping, and geospatial technologies (GPS & GIS). Science-in-action videos showcase laboratory research on materials, fluids, and surveying practices in real-world engineering systems.

civil engineering

How Aggregate Size Affects Bulk Density

Description

Transcript