5.12
Kroki przed zabiegiem obejmują zdjęcie biżuterii i podwinięcie rękawów. Jednak wiele organizacji pozwala pracownikom nosić obrączki ślubne.
Sam proces…
Cała procedura mycia rąk trwa około czterdziestu do sześćdziesięciu sekund, w zależności od stopnia zabrudzenia. Do szorowania potrzeba co najmniej 20 sekund.
Przed rozpoczęciem prania należy zdjąć wszelkie pierścionki, bransoletki czy zegarki na rękę i podwinąć rękawy.
Długie rękawy utrudniają mycie nadgarstków i mogą powodować szybkie ponowne zanieczyszczenie, podczas gdy noszenie biżuterii lub zegarka na rękę pozwala na pozostawienie mikroorganizmów na i pod akcesorium po umyciu rąk, dlatego najlepiej ich unikać, jeśli to możliwe.
Wszelkie skaleczenia na rękach należy przykryć wodoodpornym opatrunkiem, ponieważ pęknięcia w skórze mogą umożliwić przedostanie się potencjalnych patogenów.
Paznokcie powinny być krótkie i czyste, bez lakieru do paznokci i sztucznych paznokci, ponieważ mogą one przenosić brud i bakterie.
Aby rozpocząć mycie rąk, odkręć wodę z kranu o natężeniu przepływu, które zapobiega rozpryskiwaniu, i pozwól jej płynąć, aż poczujesz się komfortowo ciepła.
Ciepła woda jest wygodna i usuwa oleje ze skóry.
Następnie zwilż dłonie i nadgarstki wodą i nałóż tyle mydła, aby pokryć wszystkie powierzchnie.
Mydło pieni się wodą, aby przyspieszyć mycie rąk i usuwa brud, materiał organiczny i mikroorganizmy.
View the full transcript and gain access to JoVE Core videos
Q1: Why should jewelry and watches be removed before handwashing?
Jewelry and wristwatches allow microorganisms to remain on and beneath the accessories even after handwashing, preventing effective decontamination. Removing these items ensures all hand surfaces are properly cleaned and reduces infection risk. Many organizations allow wedding rings as an exception to this requirement.
Q2: How long does a proper handwashing procedure take?
The entire handwashing procedure takes approximately 40 to 60 seconds, depending on the extent of contamination. A minimum of 20 seconds is required for scrubbing to effectively remove dirt, organic material, and microorganisms from all hand surfaces. Adequate time ensures thorough decontamination.
Q3: What should be done about cuts or abrasions on the hands before washing?
Any cuts on the hands should be covered with a waterproof dressing before handwashing. Breaks in the skin may allow potential pathogens to gain entry, and repeated handwashing can worsen an injury. Waterproof dressings protect the wound while allowing proper hand hygiene.
Q4: Why is nail hygiene important in handwashing procedures?
Fingernails should be kept short and clean, without nail polish or artificial nails, as these can harbor dirt and bacteria. Long nails, fake nails, and nail polish imperfections are not entirely removed by handwashing, making proper nail maintenance essential for infection prevention.
Q5: What is the correct way to turn on the tap water for handwashing?
Turn on the tap water at a flow rate that prevents splashing and direct the water flow away from the drain. Drain openings are often contaminated with microorganisms that could be transferred to the environment or user if splashing occurs. Allow water to run until it feels comfortably warm.
Q6: Why should sleeves be rolled up before handwashing?
Long sleeves hinder the washing of wrists and can cause quick re-contamination after handwashing. Rolling up sleeves ensures wrists are fully accessible for cleaning and prevents contaminated fabric from recontaminating clean hands. This step is essential for maintaining hand cleanliness throughout the procedure.
Q7: How should soap be applied during the handwashing procedure?
Apply enough soap to cover all hand surfaces after wetting hands with water. Soap lathers with water to speed up handwashing and removes dirt, organic material, and microorganisms. Applying soap directly onto dry hands may damage the skin, so hands should be wet first.