Name: single phase transformer testing
Uploaded: 2023-04-30T06:42:08.000Z
Duration: 10 min 50 s
Channel: JoVE

K12 Standards

south-carolina-college-and-career-ready-science-standards

South Carolina College and Career Ready Science Standards

High School

Physics

motion-and-stability-forces-and-interactions

Motion and Stability: Forces and Interactions

P-PS2-6.

Single Phase Transformers

1. DC Test
<ol>
	<li>Turn on the low-voltage DC power supply available on the bench.</li>
	<li>Set its voltage output to 0 V, and set the current limit to 0.8 A.</li>
	<li>Double-check the circuit connections, then connect the power supply output across the primary side windings (IN1 and IN2). Leave the secondary side windings (OUT1 and OUT2) open.</li>
	<li>Turn on the supply and slightly increase the voltage until the current limit is reached. Note that the supply might already be current-limited when the supply is turned on. Do not increase the current limit. </li>
	<li>Record the voltage and current readings from the power supply display.</li>
	<li>Set the voltage back to 0 V and disconnect the supply.</li>
	<li>Adjust the current limit to 4 A, then connect the supply output across the secondary side windings (OUT1 and OUT2). Leave the primary side windings (IN1 and IN2) open.</li>
	<li>Turn on the supply and slightly increase the voltage until the current limit is reached. Note that the supply might already be current-limited when the supply is turned on. Do not increase the current limit.</li>
	<li>Record the voltage and current readings from the power supply display. For this transformer, the input voltage is 3.5 V and the current is 0.8 A.</li>
	<li>Set the voltage back to 0 V, turn the supply off, and disconnect it.</li>
	<li>Measure the resistance across the primary windings with a multi-meter.</li>
	<li>Measure the resistance across the secondary windings with a multi-meter.</li>
	<li>It is common to have the higher voltage side resistance to be higher than the lower voltage side resistance due to the fact that power on both sides is ideally equal, and higher voltage means lower current and thus lower resistance. The DC test and measured resistance on the multi-meter should match closely.</li>
</ol>
2. Open-circuit Test
<ol>
	<li>Make sure the three-phase source is off.</li>
	<li>Connect the circuit for the open-circuit test (Fig. 1). Use a digital power meter.</li>
	<li>Make sure the VARIAC is at 0%.</li>
	<li>Double-check that the circuit connections are as expected from Fig. 1, and then turn on the three-phase source.</li>
	<li>Slowly adjust the VARIAC knob until the voltage reading on the digital power meter reaches 24 V.</li>
	<li>Record the voltage, current, real power, and power factor of the power meter.</li>
	<li>Set the VARIAC back to 0%, turn off the three-phase source, and disconnect the VARIAC output.</li>
	<li>In the open-circuit or no-load test, the magnetizing reactance (Xm) and core loss resistance (RC) are found from the current (IOC), voltage (VOC), and power (POC) measurements as follows: 
	RC= VOC2/POC (1) 
	and Xm= VOC2/QOC (2) 
	where QOC2=(VOCIOC)2 - POC2 (3)</li>
</ol>
<img alt="Three-phase circuit diagram with variac, illustrating output connections and cable layout." src="/files/ftp_upload/10151/10151fig1.jpg" data-altupdatedat="1761830439000" data-alt="Figure 1"> 
Figure 1: DC test schematic. <a href="//cloudfront.jove.com/files/ftp_upload/10151/10151fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
3. Short-circuit Test
<ol>
	<li>Make sure the three-phase source is off.</li>
	<li>Connect the circuit for the short-circuit test (Fig. 2). Make sure IN1 and IN2 are connected to the VARIAC output.</li>
	<li>Make sure the VARIAC is at 0%.</li>
	<li>Calculate the rated input current of the transformer. This is found by dividing the VA rating by the voltage rating on the input side. For example, if the input is 115 V and the VA rating is 100 VA, the input current rating is 100/115= 0.87 A.</li>
	<li>Check the circuit, and then turn on the three-phase source.</li>
	<li>Slowly and carefully adjust the VARIAC knob until the current reading on the digital power meter reaches rated input current.</li>
	<li>Record the voltage, current, real power, and power factor on the power meter.</li>
	<li>Set the VARIAC back to 0%, turn off the disconnect switch, and disconnect the VARIAC output. Keep the VARIAC three-phase cable connected.</li>
	<li>Remove the short circuit placed across the transformer secondary.</li>
	<li>In the short-circuit test, the leakage reactance (X1+X2'=Xeq) and wire resistance (R1+R2'=Req) of both windings are found from the current (ISC), voltage (VSC), and power (PSC) measurements as follows: 
	Req=PSC/ISC2 (4) 
	and Xeq= QSC/ISC2 (5) 
	where QSC2=(VSC ISC)2 - PSC2 (6)</li>
	<li>X1 is assumed to be equal to X2', while R1 and R2' can be used from the DC test (or at least one of them). If the DC test is not performed, it is common to assume that R1 and R2' are equal.</li>
</ol>
<img alt="Three-phase short circuit test diagram with Variac, transformer, five-wire cable setup." src="/files/ftp_upload/10151/10151fig2.jpg" data-altupdatedat="1761830439000" data-alt="Figure 2"> 
Figure 2: Short-circuit test schematic. <a href="//cloudfront.jove.com/files/ftp_upload/10151/10151fig2large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
4. Load Test
Load tests show how the current and voltage values correlate between the input and output sides of the transformer where ideally, V1/V2 = I2/I1 = N1/N2 = a where N is the number of turns, subscripts 1 and 2 are for the primary and secondary sides, respectively, and a is the turns ratio. The impedance on the secondary side reflected to the primary side is R'=a2R or X'=a2X.
<ol>
	<li>Make sure the three-phase source is off.</li>
	<li>Connect the circuit for the load test (Fig. 3). Make sure IN1 and IN2 are connected to the VARIAC output.</li>
	<li>Make sure the VARIAC is at 0%.</li>
	<li>Connect an oscilloscope differential voltage probe across the primary with a 1/200 setting. Adjust the probe measurement for 0 V offset with an appropriate scaling factor.</li>
	<li>Connect an oscilloscope current probe to measure the load current. Adjust the probe measurement for 0 mV offset with a 1X scaling factor for a 100 mV/A setting.</li>
	<li>Check the circuit, and then turn on the three-phase disconnect switch.</li>
	<li>Slowly adjust the VARIAC knob until VP reads 115 V.</li>
	<li>Record the voltage, current, real power, and power factor of both digital power meters.</li>
	<li>Capture the oscilloscope screen with at least three cycles shown.</li>
	<li>Turn off the three-phase source and set the VARIAC at 0%.</li>
	<li>Replace the 100 Ω resistor with three 100 Ω resistors in parallel.</li>
	<li>Turn on the three-phase source and slowly adjust the VARIAC knob until VPreads 115 V.</li>
	<li>Record the two digital power meter readings only (no oscilloscope screen capture).</li>
	<li>Set the VARIAC back to 0%, turn off the disconnect switch, and disconnect the setup.</li>
</ol>
<img alt="Three-phase transformer diagram; VARIAC setup, voltage, and current measurement; circuit symbols." src="/files/ftp_upload/10151/10151fig3.jpg" data-altupdatedat="1761830439000" data-alt="Figure 3"> 
Figure 3: Load test schematic. <a href="//cloudfront.jove.com/files/ftp_upload/10151/10151fig3large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>

The described tests are critical in evaluating the impedance of a transformer and in determining its equivalent circuit parameters. Since transformer applications vary from simple chargers to high power AC transmission, appropriately characterizing different transformers for various applications is essential. Transformer impedance is used in power systems to determine possible fault impedances on either side of a transformer, approximate the efficiency of a transformer, calculate its line...

single phase transformers

Source: Ali Bazzi, Department of Electrical Engineering, University of Connecticut, Storrs, CT.
Transformers are stationary electric machines that step up or down AC voltage. They are typically formed of primary and secondary coils or windings, where the voltage on the primary is stepped up or down at the secondary, or the other way around. When a voltage is applied to one of the windings and current flows in that winding, flux is induced in the magnetic core, coupling both windings. With an AC current, AC flux is induced, and its rate of change induces voltage on the secondary winding (Faraday&#39;s law). Flux linkage between both windings depends on the number of turns of each winding; therefore, if the primary windings have more turns than the secondary winding, voltage will be higher on the primary than on the secondary, and vice versa.
This experiment characterizes a single-phase transformer by finding its equivalent circuit parameters. Three tests are performed: open-circuit test, short-circuit test, and the DC test.

By performing the DC, open-circuit, short-circuit, and load tests, the transformer&#39;s equivalent circuit parameters were identified; therefore, simulating, operating, and analyzing realistic transformer behavior become possible.
The short circuit test is usually performed by applying an increasing voltage on the high voltage side, since only small voltages on that side may cause rated current to flow on the shorted low voltage side. This is useful in operating the transformer at rated curre...

Source: Ali Bazzi, Department of Electrical Engineering, University of Connecticut, Storrs, CT.
Transformers are stationary electric machines that step up ...

Single phase transformers are used in power supplies and other equipment to convert AC voltages and currents from one value to another. Transformers are critical for providing electrical isolation which is necessary for the safe operation of many laboratory instruments and medical devices. If the input and output do not share a common terminal, then the transformer can transfer power with complete physical separation. This prevents electricity on the hazardous high-voltage side of a system from reaching circuits and people on the safe low-voltage side. Understanding the components within a transformer is important for transformer analysis and design. This video will demonstrate how to measure electrical parameters of transformer components by performing various tests.A transformer has a pair of input terminals connected to a primary winding or coil and a pair of output terminals connected to a secondary winding. A core consisting of steel, ferrite or even simply air magnetically couples the two windings. A voltage across one winding causes current to flow through it, creating a magnetic field. Magnetic flux, which is the amount of magnetic field passing through an area is then coupled through the core to the secondary winding where it induces a voltage. This principal is called mutual induction. Faraday's Law states that flux's rate of change times the number of windings is equal to the induced voltage. Also called the Electromotive Force or EMF. A DC voltage across the primary winding is constant therefore the resulting magnetic flux is also constant and the rate of change is zero. However an AC voltage produces a magnetic flux with a non-zero rate of change and consequently induces a voltage. In other words an AC voltage is required for the transformer to operate. The transformer turns ratio is the number of turns of wire on the primary winding divided by the number of turns on the secondary winding. The ratio of voltage across the primary to voltage across the secondary is equal to the turns ratio. Depending on the turns ratio a transformer can step up voltage, step down voltage or keep it the same. The ratio of current through the primary to current through the secondary is equal to the inverse of the turns ratio. For example if the primary coil has three turns and the secondary has 30 turns, the turns ratio is 0.1. Thus 120 volts on the primary of this transformer becomes 1200 volts on the secondary. 10 amps through the primary becomes 1 amp through the secondary. Finally if the secondary coil has a load of impedance Z2, the primary coil has an apparent or reflective load, Z2 prime. The value of this reflective load is the impedance on the secondary side multiplied by the square of the turns ratio. A transformer can be considered a pair of coupled inductors which ideally transfers energy without loss from one coil to the other. However a real transformer has leaked magnetic flux or leakage inductance which does not contribute to the transfer of energy between windings. Furthermore a real transformer experiences power dissipation and heating from winding resistances. Magnetic flux induced in the core is an additional source of heat due to core loss resistance. To avoid damage a specified maximum power input is used called the VA rating or the product of input voltage and the current which is power. Now that the basics of a transformer have been introduced, let's take a look at how to measure a transformer's electrical parameters.The transformer used in this experiment is rated to tolerate a maximum of 115 volts on the primary winding and a maximum of 24 volts on the secondary winding. Furthermore, this transformer has a power rating of 100VA meaning that it can accept a maximum of 100 watts of power. This DC test measures the resistance of each winding for use in the equivalent circuit model of the transformer. First set the low-voltage DC power supply voltage output to zero volts and the current limit to 0.8 amps. Then turn the supply off. Connect the power supply output across the primary winding. Do not connect anything to the secondary winding. Turn on the DC power supply and increase the voltage gradually until the current limit is reached. Record the voltage and current readings from the display of the power supply. Calculate the resistance of the primary winding by dividing the voltage by the current. Set the power supply voltage back to zero volts and turn it off. Connect the power supply across the secondary winding leaving an open circuit on the primary winding. Set the current limit on the power supply to four amps. Then increase the voltage gradually until the current limit is reached. Record the voltage and current readings from the display of the power supply. Calculate the resistance of the secondary winding. Set the power supply voltage back to zero volts, turn it off and disconnect it from the transformer. Finally use a multi-meter to confirm the calculated resistances across the primary and secondary windings.The open circuit test measures the mutual reactants or the opposition to a change in current from the core loss resistance. Core loss resistance is the equivalent circuit parameter for power dissipation and approximates power losses in the core of the transformer. With the three-phase power source off and the Variac set to zero percent, assemble the circuit as shown. Then use a digital power meter to measure open-circuit current and voltage on the primary side. Turn on the three-phase power source and slowly adjust the Variac's control knob to increase voltage until the digital power meter reads 24 volts. Record the open-circuit voltage, open-circuit current, open-circuit real power and power factor. Use these values to calculate equivalent circuit parameters for the transformer. The core loss resistance, RC is calculated from the open-circuit voltage and open-circuit power. The mutual reactance XM is calculated similarly using open circuit voltage, power and current.The short circuit test measures the leakage reactants and can also determine the wire resistance of both windings. First calculate the rated input current of the transformer by dividing the VA rating by the voltage rating for the input side. With the power source off, and Variac at zero percent output assemble the circuit as shown. This time use the digital power meter to measure short circuit current and voltage. Turn on the three-phase power source and slowly adjust the Variac to increase voltage until the current reading on the digital power meter reaches the rated input current. Record the short circuit voltage and current as well as the short circuit real power and the power factor. The leakage reactants is the sum of the primary side reactants and the reflected secondary side reactants which are assumed to be equal. Calculate the leakage reactants with the measurements from the short circuit test. Finally calculate the total wire resistance of both windings as the sum of the resistance of the primary winding and the reflected resistance of the secondary side winding.Transformers are very useful electrical devices which have applications in the area of power conversion and electrical isolation for safety. The load test measures the ratio of voltage across the primary to voltage across the secondary as well as the ratio of current through the primary to current through the secondary. The circuit was assembled with a 100 Ohm resistor connected to the secondary side and the current and voltage measured on both sides. With the primary side at 115 volts, the voltage, current, real power and power factor were measured on both sides. The ratio of the primary voltage to secondary voltage should ideally equal the turns ratio. A study of the olfactory sensory neurons of mice used ultraviolet light from a xenon flash tube to dissociate certain compounds. The circuitry to drive a flash tube required high voltages generated with a step-up transformer. As with all high-voltage equipment, safe design uses transformers for electrical isolation to prevent accidental short circuits between components with dangerous voltages and other electronics in the circuit.You've just watched Jove's introduction to single-phase transformers. You should now understand how a transformer works as well as how to measure its equivalent circuit parameters. Thanks for watching!

Education

JoVE Science Education

Engineering

Electrical Engineering

single phase transformer testing

Single-phase transformers step up or step down AC voltage in electric power systems. They are stationary electric machines with primary and secondary coils, also called windings. The primary winding receives the applied voltage, and the secondary winding delivers the changed voltage.

Inside the transformer, current in one winding creates magnetic flux in the core. This flux links the two windings and transfers energy between them. With AC current, the changing flux induces voltage in the secondary winding by Faraday's law. The voltage change depends on the number of turns in each winding. If the primary has more turns than the secondary, the primary voltage is higher. If the secondary has more turns, the secondary voltage is higher.

This experiment characterizes a single-phase transformer by finding its equivalent circuit parameters. It uses three tests: the open-circuit test, the short-circuit test, and the DC test. These measurements help describe how the transformer behaves under different conditions.

Single Phase Transformer Testing

electrical safety precautions and basic equipment

electrical-safety-precautions-and-basic-equipment

Safe Handling of High-Voltage Lab Power

Safe handling of high-voltage lab power is essential in electric machine and power electronics experiments. These labs involve electrical currents, voltages, power, and energy that require extreme care. The systems used in this work can include three-phase AC voltage at 208 V, 230 V, or 480 V. They may also use up to 250 V DC and currents that can reach 10 A. These levels can be dangerous if handled without proper attention. Electrocution can happen when electricity passes through the body.

characterization of magnetic components

B-H Curves and Inductor Core Limits

Magnetic components such as inductors and transformers depend on the core material around their windings. In this experiment, students get hands-on experience with these parts from both a design view and a material view. The work focuses on B-H curves, which show the magnetic behavior of a material. A B-H curve describes the magnetic flux density the core can support as current flows through the windings. It also helps show the limit before magnetic saturation occurs. Magnetic saturation...

introduction to the power pole board

Power Pole Board for DC/DC Converter Labs

The HiRel Power Pole Board is a flexible tool for studying DC/DC converters. A DC/DC converter changes direct-current voltage and current from one level to another. In many cases, voltage conversion is the main goal. This board supports several converter types on one platform. It can be used to examine boost converters, which step voltage up, and buck converters, which step voltage down. It also helps students study buck-boost converters, which can step voltage up or down. The board is also...

dc/dc boost converter

Stepping Up DC Voltage with Boost Converters

DC voltage can be increased with a boost converter. This step-up circuit is useful in many applications where a DC source must be raised without first converting it to AC, using a transformer, and then rectifying the transformer output. A boost converter uses an inductor as an energy storage device. The inductor supports the output with extra energy in addition to the DC input source. That added energy raises the output voltage. This experiment studies several characteristics of a boost...

dc/dc buck converter

Buck Converter Step-Down DC Voltage

A DC/DC buck converter steps down DC voltage in an efficient, regulated way. Unlike transformers, which easily raise or lower AC voltage and current, DC systems need switching power converters to change voltage levels. The buck converter works by chopping the input DC voltage with a series input switch. An L-C low-pass filter then smooths the chopped signal and extracts the average output voltage. A diode gives the inductor current a path when the switch is off during part of the switching...

flyback converter

Flyback Converter Voltage Step-Up and Step-Down

A flyback converter is a buck-boost converter that can both step voltage up and step it down. It also provides electrical isolation between the input and the output by using a coupled inductor, or flyback transformer. The coupled inductor acts like a transformer with a turns ratio, but it also stores energy through the air gap. This setup gives the converter both voltage step-up and step-down capability. In the experiment, the converter is studied in open-loop operation with a manually set...

Single-phase transformers step up or step down AC voltage in electric power systems. They are stationary electric machines with primary and secondary coils, also called windings. The primary winding receives the applied voltage, and the secondary winding delivers the changed voltage. Inside the transformer, current in one winding creates magnetic flux in the core. This flux links the two windings and transfers energy between them. With AC current, the changing flux induces voltage in the...

single phase rectifiers

AC to DC Conversion with Rectifiers

Rectifiers convert AC power into DC power for electronic circuits. A DC power supply provides unidirectional voltage and current. Batteries can do this, but they are limited by lifetime and cost. Using a rectifier is another way to turn AC line power into DC power. A rectifier is a device that lets current pass in one direction and blocks it in the other. It works after a forward voltage threshold is reached. Rectifiers may use a diode, a silicon controlled rectifier, or other silicon P-N...

thyristor rectifier

Controlling SCR Half-Wave Rectification

Thyristors, also called silicon controlled rectifiers (SCRs), are used to control current in a rectifier circuit. Like diodes, they let current pass from the anode to the cathode and block current in the opposite direction. Unlike a diode, a thyristor can be turned on with a gate terminal that receives a small current pulse. A thyristor is a four-layer device with alternating n-type and p-type layers. These layers form a PNPN structure with three junctions. The device has three terminals. The...

single phase inverter

DC to AC Conversion with Half-Bridge Inverters

DC to AC conversion is the main idea behind a power inverter. DC power flows in one direction, while AC current changes direction at about 50-60 Hz. Many electronic devices are designed to run on AC power, so a DC source must be inverted before it can be used with them. An inverter makes this change through switching action. The switches repeatedly flip the polarity of the input DC source at the output, or load side, for part of a switching period. A typical power inverter needs a stable DC...

dc motors

DC Motors and Generator Action

DC machines use direct current and direct voltage to create motion or generate electricity. They were the first machines of this kind to be invented. A DC machine works with two magnetic fields that are controlled by DC currents, and the same machine can be set up as either a motor or a generator when the right field excitation is available. In a DC machine, the field is usually on the stator side and the armature is on the rotor side. That arrangement is the reverse of what is found in many...

ac induction motor characterization

Three-Phase Motor Equivalent Circuit Tests

Three-phase induction motor testing can be used to find equivalent circuit parameters. The experiment uses the per-phase equivalent circuit to model the motor. This model keeps the important behavior of the original system and makes calculations easier. The procedure uses tests similar to those used in transformer characterization. These measurements help estimate the motor's circuit values from its electrical response. The experiment also aims to operate the motor in the linear torque-speed...

vfd-fed ac induction machine

Variable Frequency Drive Speed Control

Variable frequency drives, or VFDs, control the speed of AC induction motors. They are a type of adjustable speed drive and are becoming standard equipment for powering most AC induction motors. In industrial and automation settings, VFDs can provide strong control of motor speed, torque, or position. This experiment focuses on speed control with open-loop operation. It uses constant voltage-to-frequency ratio control, also called V/f control. The motor usually operates at a rated stator flux,...

ac synchronous machine synchronization

Grid Connection of AC Synchronous Generators

AC synchronous generators are a major source of electrical power worldwide. They are three-phase, wound-rotor machines that are used in many power plants. These generators need a prime mover and an exciter to produce power. A prime mover is the device that spins the generator, often a turbine driven by fluid. That fluid can come from water flowing from a dam through a long nozzle or from steam made by burning coal. Most power plants use synchronous generators, including coal, nuclear, natural...

ac synchronous machine characterization

Three-Phase Synchronous Motor Starting and V-Curves

Three-phase synchronous motors and generators are important AC machines. Wound-rotor synchronous motors are less common than permanent magnet rotor synchronous motors because the rotor field uses brushes. Synchronous generators are much more common. They are used in most existing power plants because they provide excellent frequency and voltage regulation. A synchronous motor runs at the same speed as the stator magnetic field. This gives it almost 0% speed regulation, so the rotor speed stays...

electrical engineering

This collection starts with an electrical safety video that introduces the best practices for commonly used equipment in an electrical laboratory. Subsequent videos introduce elements such as inductors, transformers, convertors, rectifiers, and inverters.

Learn how a single-phase transformer works and how open-circuit, short-circuit, and DC tests are used to find its equivalent circuit parameters.

Single Phase Transformer Testing | JoVE K12

Ali Bazzi

Overview

Principles of Single-phase Transformers

DC Test for Winding Resistance

Open Circuit Test

Short Circuit Test

Applications

Summary

Newton's Second Law

Newton&#39;s second law is closely related to his first law of motion. It mathematically gives the cause-and-effect relationship between force and changes ...

Second Law: Motion under Same Force

Newton&#39;s laws can be applied to bodies at rest and bodies in motion. Newton&#39;s first law is applied to bodies in equilibrium, whereas the second ...

Force and Acceleration

Source: Nicholas Timmons,&#160;Asantha Cooray, PhD, Department of Physics &#38; Astronomy, School of Physical Sciences, University of California, Irvine, ...

second-law-motion-under-same-acceleration

Second Law: Motion under Same Acceleration

Newton&#39;s second law of motion applies to bodies moving under the same acceleration. For example, when a baggage tractor pulls luggage carts, each cart ...

Newton's Laws of Motion

Source: Andrew Duffy, PhD, Department of Physics, Boston University, Boston, MA
This experiment examines at various situations involving two interacting ...

Newton's Law of Motion

When we observe objects around us, one question that comes to mind is why they move or stay still. The answer to this question can be explained using ...

Analyze data to support the claim that Newton's second law of motion describes the mathematical relationship among the net force on a macroscopic object, its mass, and its acceleration.

P-PS2-1

Force and Momentum

Force and momentum are intimately related. Force acting over time can change momentum, and Newton&#39;s second law of motion can be stated in its most ...

Internal and External Forces

Newton&#39;s first law states that a net external force causes a change in motion. External forces act on an object or system, originating outside of the ...

Conservation of Momentum: Introduction

The total momentum of a system consisting of N interacting objects is constant in time or is conserved. A system must meet two requirements for its ...

Force

Forces affect every moment of our life. Our bodies are held to the Earth by force, and they are held together by the forces of charged particles. When we ...

Conservation of Momentum

Conservation of Momentum: Problem Solving

Solving problems using the conservation of momentum requires four basic steps:

	Identify a closed system, where the total mass is constant, and no net ...

conservation-of-linear-momentum-for-a-system-of-particles

Conservation of Linear Momentum for a System of Particles

In a game of billiards, when the cue ball strikes a stationary ball, it transfers some of its momentum to the stationary ball. The cue ball slows down, ...

principle-of-linear-impulse-and-momentum-for-a-system-of-particles

Principle of Linear Impulse and Momentum for a System of Particles

Consider a system of particles moving relative to an inertial frame of reference.
The equation of motion for such a system can be written as the sum of ...

Use mathematical representations to support the claim that the total momentum of a system of objects is conserved when there is no net force on the system.

P-PS2-2

principle-of-linear-impulse-and-momentum-for-a-single-particle

Principle of Linear Impulse and Momentum for a Single Particle

Linear momentum is a fundamental concept in physics that describes the motion of an object. It is a vector quantity, having a magnitude equal to the ...

principle-of-angular-impulse-and-momentum-problem-solving

Principle of Angular Impulse and Momentum: Problem Solving

Consider a ball of mass m, attached to a massless rod of known length, subjected to a time-dependent torque. If the initial velocity of the mass is known, ...

Linear Momentum

The term momentum is used in various ways in everyday language, most of which are consistent with the precise scientific definition. Generally, momentum ...

principle-of-angular-impulse-and-momentum

Principle of Angular Impulse and Momentum

The angular impulse and momentum principle provides insights into how forces applied at a distance from an object&#39;s rotational axis influence its ...

principle-linear-impulse-momentum-for-single-particle-problem

Principle of Linear Impulse and Momentum for a Single Particle: Problem Solving

Consider a massless pulley system consisting of a wooden box and a cylinder of known masses. Determine the speed of the attached objects at a specific ...

Angular Momentum

Angular momentum describes the rotational motion of an object.
It is defined as the moment of the object&#39;s linear momentum about a specific point O.
...

relation-between-moment-of-a-force-and-angular-momentum

Relation Between Moment of a Force and Angular Momentum

In a spinning top, applying a force at a distance from the center creates torque, which changes the angular momentum of the top, causing it to spin.
The ...

Apply scientific and engineering ideas to design, evaluate, and refine a device that minimizes the effect of a force on a macroscopic object during a collision.

P-PS2-3

Gravitation

In the years before Newton, a general belief prevailed that different laws governed objects in the sky than objects on Earth. When Kepler wrote down the ...

/files/media/science-education/science-education-thumbs/14716.jpg

Newton's Law of Gravitation

Our everyday observation tells us that all objects close to the Earth naturally tend to fall to the ground. Early philosophers assumed that this downward ...

gravitation-between-spherically-symmetric-masses

Gravitation Between Spherically Symmetric Masses

The gravitational potential energy between two spherically symmetric bodies can be calculated from the masses and the distance between the bodies, ...

/files/media/science-education/science-education-thumbs/14717.jpg

Gravity between Spherical Bodies

Newton&#39;s law of gravitation describes the gravitational force between any two point masses. However, for extended spherical objects like the Earth, ...

Coulomb's Law

Experiments with electric charges have shown that if two objects each have an electric charge, they exert an electric force on each other. The magnitude ...

comparison-between-electrical-and-gravitational-forces

Comparison Between Electrical And Gravitational Forces

There are four fundamental forces in nature: the gravitational force, the electromagnetic force, the strong nuclear force, and the weak nuclear force. To ...

Newton's Law of Gravitational Attraction

Sir Isaac Newton established the universality of the law of gravitational attraction based on empirical evidence and inductive reasoning. He published his ...

Newton's Law of Universal Gravitation

Source: Ketron Mitchell-Wynne, PhD,&#160;Asantha Cooray, PhD, Department of Physics &#38; Astronomy, School of Physical Sciences, University of ...

Use mathematical representations of Newton's law of gravitation and Coulomb's law to describe and predict the gravitational and electrostatic forces between objects.

P-PS2-4

Types of Forces

In most situations, forces can be grouped into two categories: contact forces and field forces.&#160; Contact forces occur as a result of direct physical ...

Magnetic Fields

Source: Yong P. Chen, PhD, Department of Physics &#38; Astronomy, College of Science, Purdue University, West Lafayette, IN
Magnetic fields can be ...

Electric Charge in a Magnetic Field

Source: Andrew Duffy, PhD, Department of Physics, Boston University, Boston, MA
This experiment duplicates J.J. Thomson's famous experiment at the end of ...

Electric Fields

Source: Yong P. Chen, PhD, Department of Physics &#38; Astronomy, College of Science, Purdue University, West Lafayette, IN
An electric field is generated ...

Electromagnetic Fields

Electric fields generated by static charges, often referred to as electrostatic fields, are characteristically different from electric fields created by ...

Magnetic Field Due to Two Straight Wires

Consider two parallel straight wires carrying a current of 10 A and 20 A in the same direction and separated by a distance of 20 cm. Calculate the ...

Energy Carried By Electromagnetic Waves

Anyone who has used a microwave oven knows there is energy in electromagnetic waves. Sometimes, this energy is obvious, such as in the summer sun&#39;s ...

Energy Stored in Capacitors

A parallel plate capacitor connected to a battery develops a potential difference across its plates.
By integrating the equation relating voltage and ...

Power and Energy

Energy is the total work required to drive the current through the circuit.
A rise in voltage results in more work done, passing more current, resulting ...

Voltage

The movement of electrons in a conductor requires some form of energy or work, usually provided by an external force, like a battery. This force is called ...

Electromotive Force

Electromotive force (emf) is the force that causes current to flow from a higher to a lower&#160; potential. The term &#34;electromotive ...

Electrical Energy

Using electric appliances for a longer period of time consumes more electrical energy and results in a higher electric bill. The energy produced by the ...

Electrical Current

Electrical current is defined as the rate at which charge flows. When there is a large current present, such as that used to run a refrigerator, a large ...

Electric Potential Energy

When an electric field accelerates a free positive charge q, it is given kinetic energy. The process is analogous to an object accelerated by a ...

Electrical Power

Electric power is the product of current and voltage, represented in units of joules per second, or watts. For example, cars often have one or more ...

Plan and conduct an investigation to provide evidence that an electric current can produce a magnetic field and that a changing magnetic field can produce an electric current.

P-PS2-5

sources-and-properties-of-electric-charge

Sources and Properties of Electric Charge

All objects we see around us consist of atoms, which combine to form molecules. The lightest element in the universe is hydrogen, and a hydrogen atom ...

Electric Charges

From lightning during thunderstorms to electronic devices, the phenomenon of electromagnetism is all around us. The electromagnetic force is one of the ...

Electron Behavior

Electrons are negatively charged subatomic particles attracted to and orbit around the positively-charged nucleus of an atom. They reside in spaces ...

Electronic Structure of Atoms


An atom comprises protons and neutrons, which are contained inside the dense, central&#160;core called the nucleus, with electrons present around the ...

Atomic Structure

All matter is composed of atoms, the smallest individual units of elements. Each atom is made up of three subatomic particles: protons, neutrons, and ...

Electric Field

Consider two point charges, each exerting Coulomb force on the other. It is possible to describe the Coulomb interaction via an intermediate step by ...

Communicate scientific and technical information about why the molecular-level structure is important in the functioning of designed materials.

Single Phase Transformer Testing

Description

Transcript

Tags

More videos by Standards