Name: dc motors
Uploaded: 2023-04-30T06:43:07.000Z
Duration: 9 min 29 s
Channel: JoVE

K12 Standards

Arizona Science Standards

High School

Physical Science

HS.P3

HS.P3U2.7

DC Motors

1. DC Tests
<ol>
	<li>With the low-power DC power supply limited to 0.8 A, connect the supply terminals to the DC machine armature.</li>
	<li>Record the supply's DC voltage and current readings.</li>
	<li>Estimate the resistance of each winding.</li>
	<li>Repeat for the other windings, shunt field and series field, one at a time.</li>
	<li>Turn off and disconnect the low-power DC power supply.</li>
	<li>Set the built-in field rheostat to maximum resistance and measure its resistance.</li>
	<li>Set the series field rheostat (external) to the maximum resistance and measure its resistance.</li>
</ol>
2. Prime-Mover Setup and Residual Magnetism
The prime-mover in this experiment is the synchronous machine, which operates as a motor that spins the DC generator rotor (armature).
<ol>
	<li>Make sure the three-phase disconnect switch, synchronous motor switch, and DC motor switch are all off.</li>
	<li>Check that the VARIAC is at 0%.</li>
	<li>Wire the VARIAC to the three-phase outlet, and connect the setup shown in Fig. 5.</li>
	<li>Check that the "Start/Run" switch is in the "Start" position.</li>
	<li>Turn on the three-phase disconnect switch.</li>
	<li>Turn on the high-voltage DC power supply.</li>
	<li>Make sure all connections are clear from the supply terminals.</li>
	<li>Press the "V/I DIS" button on the supply to display the voltage and current operating points. Adjust the voltage knob to 125 V.
	<ol>
		<li>Do not press the start button.</li>
	</ol>
	</li>
	<li>Press the "Start" button on the DC power supply panel.</li>
	<li>Slowly increase the VARIAC output until VAC1 reads 120 V.</li>
	<li>When the synchronous motor reaches a steady-state speed, flip the Start/Run switch into the Run position.</li>
	<li>Measure and record the rotational speed using the strobe light and record VA.</li>
	<li>Turn off the DC power supply and return the VARIAC to 0%.</li>
	<li>Reset the "Start/Run" switch to "Start."</li>
	<li>Turn off the three-phase disconnect switch.</li>
</ol>
<img alt="Synchronous motor diagram, high voltage DC setup, variac, dynamometer, mechanical coupling." src="/files/ftp_upload/10166/10166fig5.jpg" data-altupdatedat="1761830439000" data-alt="Figure 5"> 
Figure 5: A schematic of how to setup the prime-mover. <a href="//cloudfront.jove.com/files/ftp_upload/10166/10166fig5large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
3. DC Shunt Generator Characterization
<ol>
	<li>On the DC generator side, connect the shunt field in parallel with the armature field as shown in Fig. 6.</li>
	<li>Use the built-in rheostat for RFsh(ext), and use the multi-meter as an ammeter to measure IFsh.</li>
	<li>Keep "S1" open for a no-load test.</li>
	<li>Keep "RFsh(ext)" at maximum resistance.</li>
	<li>Turn on the three-phase disconnect switch.</li>
	<li>Press the "Start" button on the DC power supply panel.</li>
	<li>Slowly increase the VARIAC output until VAC1 reads 120 V.</li>
	<li>When the synchronous motor reaches a steady-state speed, flip the "Start/Run" switch into the "Run" position.</li>
	<li>Measure the shaft speed using the strobe-light technique described elsewhere.</li>
	<li>Record VA at this no-load condition on the DC generator side.</li>
	<li>Reduce RFsh(ext) until the voltage generated at VA is around 150 V.</li>
	<li>After that point, reduce "RFsh(ext)" in five almost-equal steps until the minimum resistance is reached.
	<ol>
		<li>For each step, measure VA and IFsh.</li>
	</ol>
	</li>
	<li>Leave RFsh(ext) at its minimum value.</li>
	<li>Turn off the DC power supply.</li>
	<li>Reduce the VARIAC output to 0%.</li>
	<li>Move the ammeter from measuring IFsh to measure IA.</li>
	<li>Restart the setup as described earlier.</li>
	<li>Set RL to 300 Ω, and turn on "S1". Measure VA and IA.</li>
	<li>Turn off "S1," set RL to 200 Ω, then turn on "S1." Measure VA, and IA.</li>
	<li>Turn off "S1," set RL to 100 Ω, then turn on "S1." Measure VA, and IA.</li>
	<li>Turn off the DC power supply and set the VARIAC output to 0%.</li>
	<li>Keep the synchronous generator side of the setup intact.</li>
	<li>Disconnect the DC generator connections.</li>
	<li>Reset the "Start/Run" switch to "Start."</li>
	<li>Turn off the three-phase disconnect switch.</li>
</ol>
<img alt="Synchronous motor diagram with variac, high voltage DC power supply, and dynamometer coupling setup." src="/files/ftp_upload/10166/10166fig6.jpg" data-altupdatedat="1761830439000" data-alt="Figure 6"> 
Figure 6: A schematic of the shunt DC generator setup. <a href="//cloudfront.jove.com/files/ftp_upload/10166/10166fig6large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
4. DC Series Generator Characterization
<ol>
	<li>On the DC generator side, connect the series field in series with the armature field as shown in Fig 7.
	<ol>
		<li>Use the external rheostat for RFse(ext).</li>
		<li>Use the built-in rheostat as RL and have it at maximum resistance.</li>
		<li>Keep "S1" open for a no-load test.</li>
		<li>Keep RFse(ext) at maximum resistance.</li>
	</ol>
	</li>
	<li>Turn on the three-phase disconnect switch.</li>
	<li>Press the "Start" button on the DC power supply panel.</li>
	<li>Slowly increase the VARIAC output until VAC1 reads 120 V.</li>
	<li>When the synchronous motor reaches a steady-state speed, flip the "Start/Run" switch into the "Run" position.
	<ol>
		<li>Measure VA at this no-load condition on the DC generator side.</li>
	</ol>
	</li>
	<li>Turn on "S1" and reduce RFse(ext) as needed to see non-zero VA.</li>
	<li>Vary RL in five almost-equal steps until its 50% setting is reached, set to 300 Ω, and turn on "S1." Measure the speed, VA, and IA.
	<ol>
		<li>Turn off "S1," set RL to 200 Ω, then turn on "S1." Measure the speed, VA, and IA.</li>
		<li>Turn off "S1," set RL to 100 Ω, then turn on "S1." Measure the speed, VA, and IA.</li>
	</ol>
	</li>
	<li>Turn off the DC power supply.
	<ol>
		<li>Set the VARIAC output to 0%.</li>
		<li>Keep the synchronous generator side of the setup intact.</li>
		<li>Disconnect the DC generator connections.</li>
		<li>Reset the "Start/Run" switch to "Start."</li>
	</ol>
	</li>
	<li>Turn off the three-phase disconnect switch.</li>
	<li>Disassemble all wires and meters.</li>
</ol>
<img alt="Synchronous motor diagram with VARIAC and dynamometer setup for mechanical-electrical conversion." src="/files/ftp_upload/10166/10166fig7.jpg" data-altupdatedat="1761830439000" data-alt="Figure 7"> 
Figure 7: A schematic of the series DC generator setup. <a href="//cloudfront.jove.com/files/ftp_upload/10166/10166fig7large.jpg" target="_blank"> Please click here to view a larger version of this figure.</a>
&lt;

DC machines are significantly less common than they used to be before the invention of AC induction and synchronous machines. They remain common in simple low power applications such as toys, small robots, and legacy equipment. Permanent magnet DC machines, which use abundant non-rare-earth magnets, are more common than their shunt and series counter parts due to simpler excitation, especially in low cost and low complexity applications.

dc motors

Source: Ali Bazzi, Department of Electrical Engineering, University of Connecticut, Storrs, CT. 
The DC machine operates with DC currents and voltages as opposed to an AC machine, which requires AC currents and voltages. DC machines were the first to be invented and utilize two magnetic fields that are controlled by DC currents. The same machine can be easily reconfigured to be a motor or generator if appropriate field excitation is available, since the DC machine has two fields termed field and armature. The field is usually on the stator side and the armature is on the rotor side (opposite or inside-out compared to AC machines). Field excitation can be provided by permanent magnets or a winding (coil). When current is applied to the armature or rotor coil, it passes from the DC source to the coil through brushes that are stationary and slip rings mounted on the rotating rotor touching the brushes. When the rotor armature coil is a current-carrying loop, and is exposed to an external field from the stator or field magnet, a force is exerted on the loop. Since the loop is "hanging" on both sides of the motor using bearings, the force produces a torque that will rotate the rotor's shaft rather than move it in any other direction.
This rotation causes the magnetic fields to align but at the same time, slip rings switch sides on the brushes, or "commute," and this is what is known as the commutation process. When this commutation occurs, current flow in the rotor coil is reversed and magnetic fields oppose each other again, causing further torque in the same direction of rotation. This process continues and the rotor shaft spins providing motor action. In generator operation, mechanical rotation is provided to the rotor shaft and current flows out of the rotor after it is induced due to a moving coil under a magnetic field.
The machines discussed in this experiment have a field winding rather than permanent magnets. A commutation process that is critical in DC machine operation uses slip rings and brushes to transfer energy from the rotor (armature) to the outside world since the rotor is spinning and having spinning wires would twist and break them. However, these brushes and slip rings have major reliability drawbacks as they require regular maintenance, brush replacement, cleaning, and may cause sparking. This has led to replacement of most DC machines by AC machines that do not have these issues, and remaining DC machines mostly have permanent magnet field excitation, such as in toys and simple low-power tools. AC machines termed brushless DC machines (or BLDCs) are AC machines that utilize a DC source and power electronic inverter to get AC voltages out of the inverter. 
The objective of this experiment is to test two main DC machine configurations: shunt and series. Tests are intended to estimate the residual flux in the machine and to study the no-load and loading characteristics of different configurations.

Series windings typically carry high current rated at the machine&#39;s rated armature current, since both series and armature windings are in series. Therefore, series windings are expected to be on the order of a m&#937; to a few &#937;. Shunt windings on the other hand should draw minimum current from the source which power them along with the machine&#39;s armature, and therefore, have large resistance values of tens to hundreds or even thousands of &#937;.
<p class="jove_content"...

Source: Ali Bazzi, Department of Electrical Engineering, University of Connecticut, Storrs, CT. 
The DC machine operates with DC currents and voltages as ...

DC Motors, drive equipment, ranging from small toys and rechargeable power tools, to electric vehicles. These electromechanical machines consist of an inner conductive coil, called the armature, and an outer magnet, called the stator. A DC source provides current to the armature through a commutator slippering. Inducing electromagnetic force and allowing rotation of the loop. The magnitude of the electromagnetic force depends on the angle between the magnetic field and the coil, creating fluctuations in torque with rotation. Multiple windings, spaced around the armature, minimize torque fluctuations, and prevent the commutator form shorting out the power supply. The commutator slippering periodically switches the direction of current through the coil, further preventing alignment of magnetic fields. This video introduces DC motor configurations, and demonstrates the measurement of DC motor performance characteristics, such as speed, current, and voltage with varying load.Permanent magnet staters, in DC machines are the most common, however, when the staters magnetic field is produced through conductor windings, performance characteristics, such as speed and torque output, can be modified through electric field design. For example, speed is related to the voltage developed by the motor, called the electro motor force, or EMF. Similarly, torque is proportional to current. These characteristics vary depending on the design of the motor, and influence the motor design selected for certain applications. The four basic electronic configurations of DC machines are separately excited, shunt, series, and compound. Separately excited motors use separate power supplies for the field and armature, allowing for independent control to support varying loads. In shunt design, the most common configuration, field windings are connected parallel to the armature load, with a common DC supply. This provides adjustable speed with varying load, which is useful in machine tools and centrifical pumps. In series configuration, a DC supply powers the field and armature in series. This delivers higher starting torque for overcoming intertial loads in equipment, such as trains, elevators, or hoists. Compound design motors use both shunt and series circuits for both high starting torque and speed regulation. The shunt field may be loading before or after the series field. Now that the configurations of DC motors have been outlined, the analysis of current, voltage, and load relationships in shunt DC motors will be demonstrated.The data collected in the DC tests can be used to build equivalent circuit models if needed. Before measuring the electrical characteristics of the DC motor, set the low power DC supply to 0.8 amps, and connect the supply terminals to the machine armature. Then, record the supplies voltage and current. Next, use a multimeter to measure voltage and current across the armature, winding the shunt field and the series field. Use the data to estimate the resistance in each component. After measuring the basic characteristics of the DC motor generator, set the built in field rheostat to the maximum settings, and measure its resistance. Finally, set the external series field rheostat to its upper limit, and measure its resistance.Following the DC motor tests, a synchronous machine is used to rotate the DC machine's armature. Thus, the DC machine is run as a generator, without field excitation, then with no load. Under these conditions, the terminal voltage equals EMF. The rotational speed of the generator is measured, and used to calculate the magnetism retained by the armature in the absence of coil excitation, called residual magnetism. First, check that the three phase disconnect, synchronous motor, and DC motor are all switched off. Then, attach a small piece of tape to the DC motor external rotor. After checking that the variac is set to zero percent, wire the variac to the three phase outlet. Next, connect the setup as shown. Then, check that the start run switch is in the start position. Following the adjustments to the variac, confirm that all connections are clear from the supply terminals. Only then, turn on the three phase disconnect switch. Next, turn on the high voltage DC power supply, press the VI display button to display the operating end current, and adjust the voltage knob to 125 volts. Do not press the start button before adjusting the voltage knob. Press the start button the DC power supply panel, and switch on the equipment. Next, slowly increase the variac output until the terminal voltage reads 120 volts. When the synchronous motor reaches a steady state rotational speed, flip the start run switch to run. Pay attention to machine sound changes. The machine sound becomes monotonic at steady state. Use the strobe light to freeze the motion of the motor by synchronizing the strobe rate to the motor rotation speed. The tape attached to the rotor will appear stationary when the strobe light is synchronized. Confirm that this rate is the motor speed by slowly increasing the strobe rate to synchronize the fan at the next highest rate. If correct, this will be double the first observed strobe synchronization rate. This start up sequence will be repeated before each subsequent test run. After startup, record the rotational speed of the motor and the armature voltage. Then use this data to calculate the residual magnetic field strength.DC machines are used in a variety of applications. Once operating parameters of different machines are characterized, they can be chosen based on design specifications for a particular device. The DC generator can be characterized in various configurations, such as the shunt configuration. With switch S1 open, for no load testing, the field end load resisters are adjusted to the maximum. Then, the shaft speed and terminal voltage are recorded as described previously. The shunt resistance is reduced in five steps until the minimum resistance is reached. And the terminal voltage and current across the shunt resistor measured. The motor can be measured with simulated loads using load resistors, following the same protocol. Each type of DC generator has its own voltage current output. Shunt generators can provide voltage for a wide range of current load, while series generators provide increasing voltage with current load. In a variety of applications, where a wireless power source is preferred, such as motorized prosthetics, DC motors are the actuator of choice. In neurally controlled lower limb prosthetics, either surface or transdermal sensors are used to send signals to motorized joints in the replacement limb, much as in an intact leg. Gate and foot flection are controlled more naturally and intuitively than would be possible using a rigid limb replacement.You've just watched Jove's introduction to DC motors. You should now understand how a DC motor works and how to characterize its parameters. Thanks for watching.

Education

JoVE Science Education

Engineering

Electrical Engineering

electrical safety precautions and basic equipment

electrical-safety-precautions-and-basic-equipment

Safe Handling of High-Voltage Lab Power

Safe handling of high-voltage lab power is essential in electric machine and power electronics experiments. These labs involve electrical currents, voltages, power, and energy that require extreme care. The systems used in this work can include three-phase AC voltage at 208 V, 230 V, or 480 V. They may also use up to 250 V DC and currents that can reach 10 A. These levels can be dangerous if handled without proper attention. Electrocution can happen when electricity passes through the body.

characterization of magnetic components

B-H Curves and Inductor Core Limits

Magnetic components such as inductors and transformers depend on the core material around their windings. In this experiment, students get hands-on experience with these parts from both a design view and a material view. The work focuses on B-H curves, which show the magnetic behavior of a material. A B-H curve describes the magnetic flux density the core can support as current flows through the windings. It also helps show the limit before magnetic saturation occurs. Magnetic saturation...

introduction to the power pole board

Power Pole Board for DC/DC Converter Labs

The HiRel Power Pole Board is a flexible tool for studying DC/DC converters. A DC/DC converter changes direct-current voltage and current from one level to another. In many cases, voltage conversion is the main goal. This board supports several converter types on one platform. It can be used to examine boost converters, which step voltage up, and buck converters, which step voltage down. It also helps students study buck-boost converters, which can step voltage up or down. The board is also...

dc/dc boost converter

Stepping Up DC Voltage with Boost Converters

DC voltage can be increased with a boost converter. This step-up circuit is useful in many applications where a DC source must be raised without first converting it to AC, using a transformer, and then rectifying the transformer output. A boost converter uses an inductor as an energy storage device. The inductor supports the output with extra energy in addition to the DC input source. That added energy raises the output voltage. This experiment studies several characteristics of a boost...

dc/dc buck converter

Buck Converter Step-Down DC Voltage

A DC/DC buck converter steps down DC voltage in an efficient, regulated way. Unlike transformers, which easily raise or lower AC voltage and current, DC systems need switching power converters to change voltage levels. The buck converter works by chopping the input DC voltage with a series input switch. An L-C low-pass filter then smooths the chopped signal and extracts the average output voltage. A diode gives the inductor current a path when the switch is off during part of the switching...

flyback converter

Flyback Converter Voltage Step-Up and Step-Down

A flyback converter is a buck-boost converter that can both step voltage up and step it down. It also provides electrical isolation between the input and the output by using a coupled inductor, or flyback transformer. The coupled inductor acts like a transformer with a turns ratio, but it also stores energy through the air gap. This setup gives the converter both voltage step-up and step-down capability. In the experiment, the converter is studied in open-loop operation with a manually set...

single phase transformers

Single Phase Transformer Testing

Single-phase transformers step up or step down AC voltage in electric power systems. They are stationary electric machines with primary and secondary coils, also called windings. The primary winding receives the applied voltage, and the secondary winding delivers the changed voltage. Inside the transformer, current in one winding creates magnetic flux in the core. This flux links the two windings and transfers energy between them. With AC current, the changing flux induces voltage in the...

single phase rectifiers

AC to DC Conversion with Rectifiers

Rectifiers convert AC power into DC power for electronic circuits. A DC power supply provides unidirectional voltage and current. Batteries can do this, but they are limited by lifetime and cost. Using a rectifier is another way to turn AC line power into DC power. A rectifier is a device that lets current pass in one direction and blocks it in the other. It works after a forward voltage threshold is reached. Rectifiers may use a diode, a silicon controlled rectifier, or other silicon P-N...

thyristor rectifier

Controlling SCR Half-Wave Rectification

Thyristors, also called silicon controlled rectifiers (SCRs), are used to control current in a rectifier circuit. Like diodes, they let current pass from the anode to the cathode and block current in the opposite direction. Unlike a diode, a thyristor can be turned on with a gate terminal that receives a small current pulse. A thyristor is a four-layer device with alternating n-type and p-type layers. These layers form a PNPN structure with three junctions. The device has three terminals. The...

single phase inverter

DC to AC Conversion with Half-Bridge Inverters

DC to AC conversion is the main idea behind a power inverter. DC power flows in one direction, while AC current changes direction at about 50-60 Hz. Many electronic devices are designed to run on AC power, so a DC source must be inverted before it can be used with them. An inverter makes this change through switching action. The switches repeatedly flip the polarity of the input DC source at the output, or load side, for part of a switching period. A typical power inverter needs a stable DC...

DC Motors and Generator Action

DC machines use direct current and direct voltage to create motion or generate electricity. They were the first machines of this kind to be invented. A DC machine works with two magnetic fields that are controlled by DC currents, and the same machine can be set up as either a motor or a generator when the right field excitation is available. In a DC machine, the field is usually on the stator side and the armature is on the rotor side. That arrangement is the reverse of what is found in many...

ac induction motor characterization

Three-Phase Motor Equivalent Circuit Tests

Three-phase induction motor testing can be used to find equivalent circuit parameters. The experiment uses the per-phase equivalent circuit to model the motor. This model keeps the important behavior of the original system and makes calculations easier. The procedure uses tests similar to those used in transformer characterization. These measurements help estimate the motor's circuit values from its electrical response. The experiment also aims to operate the motor in the linear torque-speed...

vfd-fed ac induction machine

Variable Frequency Drive Speed Control

Variable frequency drives, or VFDs, control the speed of AC induction motors. They are a type of adjustable speed drive and are becoming standard equipment for powering most AC induction motors. In industrial and automation settings, VFDs can provide strong control of motor speed, torque, or position. This experiment focuses on speed control with open-loop operation. It uses constant voltage-to-frequency ratio control, also called V/f control. The motor usually operates at a rated stator flux,...

ac synchronous machine synchronization

Grid Connection of AC Synchronous Generators

AC synchronous generators are a major source of electrical power worldwide. They are three-phase, wound-rotor machines that are used in many power plants. These generators need a prime mover and an exciter to produce power. A prime mover is the device that spins the generator, often a turbine driven by fluid. That fluid can come from water flowing from a dam through a long nozzle or from steam made by burning coal. Most power plants use synchronous generators, including coal, nuclear, natural...

ac synchronous machine characterization

Three-Phase Synchronous Motor Starting and V-Curves

Three-phase synchronous motors and generators are important AC machines. Wound-rotor synchronous motors are less common than permanent magnet rotor synchronous motors because the rotor field uses brushes. Synchronous generators are much more common. They are used in most existing power plants because they provide excellent frequency and voltage regulation. A synchronous motor runs at the same speed as the stator magnetic field. This gives it almost 0% speed regulation, so the rotor speed stays...

electrical engineering

This collection starts with an electrical safety video that introduces the best practices for commonly used equipment in an electrical laboratory. Subsequent videos introduce elements such as inductors, transformers, convertors, rectifiers, and inverters.

Explore how DC machines use brushes, slip rings, commutation, and field excitation to act as motors or generators, with shunt and series tests.

DC Motors and Generator Action | JoVE K12

south-carolina-college-and-career-ready-science-standards

South Carolina College and Career Ready Science Standards

Physics

motion-and-stability-forces-and-interactions

Motion and Stability: Forces and Interactions

P-PS2-6.

Georgia Standards of Excellence

9-12

SP5.

Applications in Motors and Generators

Ali Bazzi

Overview

Principles of DC Motors

DC Tests

Measurement of Residual Magnetism

Applications

Summary

Position and Displacement

The position of an object defines its location relative to a convenient frame of reference at any particular time. A frame of reference is an arbitrary ...

Average Velocity

To calculate the other physical quantities in kinematics, we must introduce the time variable. The time variable allows us not only to state the position ...

Average Acceleration

The importance of understanding acceleration spans our day-to-day experiences, as well as the vast reaches of outer space and the tiny world of subatomic ...

Instantaneous Acceleration

Acceleration is in the direction of the change in velocity, but it is not always in the direction of motion. When an object slows down, its acceleration ...

velocity-and-position-by-graphical-method

Velocity and Position by Graphical Method

Velocity and position can be calculated from the known function of acceleration as a function of time. The total area under the acceleration-time graph ...

Kinematic Equations - I

When an object moves with constant acceleration, the velocity of the object changes at a constant rate throughout the motion. The kinematic equations of ...

Kinematic Equations: Problem Solving

When analyzing one-dimensional motion with constant acceleration, the problem-solving strategy involves identifying the known quantities and choosing the ...

Force

Forces affect every moment of our life. Our bodies are held to the Earth by force, and they are held together by the forces of charged particles. When we ...

Mass and Weight

Mass and weight are often used interchangeably in everyday conversation. For example,&#160; medical records often show our weight in kilograms, but never ...

Newton's Laws of Motion

Source: Andrew Duffy, PhD, Department of Physics, Boston University, Boston, MA
This experiment examines at various situations involving two interacting ...

Newton's First Law: Introduction

Motion draws our attention. Motion itself can be beautiful, causing us to marvel at the forces needed to create spectacular sights, such as that of a ...

first-law-particles-in-one-dimensional-equilibrium

First Law: Particles in One-dimensional Equilibrium

Newton&#39;s first law of motion states that a body at rest remains at rest, or if in motion, remains in motion at constant velocity, unless acted on by a ...

Newton's Second Law

Newton&#39;s second law is closely related to his first law of motion. It mathematically gives the cause-and-effect relationship between force and changes ...

Force and Acceleration

Source: Nicholas Timmons,&#160;Asantha Cooray, PhD, Department of Physics &#38; Astronomy, School of Physical Sciences, University of California, Irvine, ...

Second Law: Motion under Same Force

Newton&#39;s laws can be applied to bodies at rest and bodies in motion. Newton&#39;s first law is applied to bodies in equilibrium, whereas the second ...

Newton's Third Law: Introduction

Whenever one body exerts a force on a second body, the first body experiences a force equal in magnitude and opposite in direction, to the force that it ...

Drawing Free-body Diagrams: Rules

The first step in describing and analyzing most phenomena in physics involves the careful drawing of a free-body diagram. Free-body diagrams are useful in ...

Free Body Diagrams: Examples

Solving problems that involve forces is easy using free-body diagrams. A free-body diagram is a sketch showing all the external forces that are acting on ...

Equilibrium and Free-body Diagrams

Source: Ketron Mitchell-Wynne, PhD, Asantha Cooray, PhD, Department of Physics &#38; Astronomy, School of Physical Sciences, University of California, ...

Collect, analyze and interpret data regarding the change in motion of an object or system in one dimension, to construct an explanation using Newton’s Laws.

HS.P3U1.6

Solving Problems in Physics

Problem-solving is the ability to apply general physical principles to specific situations, usually expressed by equations. It is an essential skill in ...

Problem Solving in Statics

Problem-solving in statics is a crucial aspect of engineering and physics that involves resolving issues associated with bodies in a state of equilibrium. ...

An Introduction to Mechanics

Humans have been making ships, shelters, pyramids, weapons, agricultural equipment, and many more items without recording the process or theory behind ...

Introduction to Structures

A structure is defined as a system of interconnected members designed to support or transfer forces and successfully withstand the loads acting on them. ...

Simple Trusses

A truss is a structural framework consisting of slender members connected at joints, designed to support external loads while minimizing material usage ...

Method of Joints

The method of joints is a commonly used technique to analyze the forces in structural trusses. The method is based on the principle of equilibrium, which ...

Rigid Body Equilibrium Problems - I

A rigid body is said to be in static equilibrium when the net force and the net torque acting on the system is equal to zero. To solve for rigid body ...

Stability of structures

Consider two rods connected at point O by a pin and a torsional spring of constant k. The ends of both the rods are pin-connected.
If both the rods are ...

Buckling of Steel Columns

Source:&#160;Roberto Leon, Department of Civil and Environmental Engineering, Virginia Tech, Blacksburg, VA
In the design of civil works, it is important ...

Machines

Machines are complex structures consisting of movable, pin-connected multi-force members that work together to transmit forces. One example of a machine ...

Rolling Resistance

When a solid cylinder rolls steadily on a rigid surface, the normal force applied by the surface on the cylinder is perpendicular to the tangent at the ...

Propulsion and Thrust

Source: Alexander S Rattner; Department of Mechanical and Nuclear Engineering, The Pennsylvania State University, University Park, PA
Aircraft, rockets, ...

Rocket Propulsion in Empty Space - I

The driving force for the motion of any vehicle is friction, but in the case of rocket propulsion in space, the friction force is not present. The motion ...

aerodynamic-performance-of-a-model-aircraft-the-dc-6b

Aerodynamic Performance of a Model Aircraft: The DC-6B

Source: Jose Roberto Moreto and Xiaofeng Liu, Department of Aerospace Engineering, San Diego State University, San Diego, CA
The low-speed wind tunnel is ...

airfoil-behavior-pressure-distribution-over-a-clark-y-14-wing

Airfoil Behavior: Pressure Distribution over a Clark Y-14 Wing

Source: David Guo, College of Engineering, Technology, and Aeronautics (CETA), Southern New Hampshire University (SNHU), Manchester, New Hampshire
An ...

Use mathematics and computational thinking to explain how Newton’s laws are used in engineering and technologies to create products to serve human ends.

DC Motors

Description

Transcript

Tags

More videos by Standards