Name: concrete workability check with slump
Uploaded: 2024-11-07T14:48:28.000Z
Duration: 1 min 20 s
Channel: JoVE

The slump test measures concrete workability and uses a 12-inch high truncated cone mold, narrowing from eight inches at the base to four inches at the top, securely attached to a flat base before the concrete is filled.
The concrete is added to the dampened mold in three layers, each compacted 25 times using a steel tamping rod with a five-eighths-inch diameter and rounded end. Finally, the top surface is struck off.
After filling, the cone is gently lifted, and the concrete slumps. This decrease in its height, called a slump, is measured to the nearest quarter inch.
A uniform slump is called a true slump, while concrete that slides down the mold indicates a shear slump, which requires retesting. Persistent shear slump suggests the mix lacks cohesion.
Sometimes, the concrete may collapse for lean mixes, which highlights the slump test&#39;s unreliability for lean mixes.
Slump, either too high or too low, serves as an immediate alert, prompting correction of the issue with the mix in bulk concreting. Recommended slump values for different workabilities are predetermined.

slump test

The slump test is a widely used method to measure the workability of concrete. It employs a 12-inch high truncated cone mold that tapers from eight inches at the base to four inches at the top. Before testing, the mold is securely attached to a flat base and dampened.
Concrete is poured into the mold in three layers to conduct the test. Each layer is compacted 25 times with a steel tamping rod, which has a five-eighths-inch diameter and a rounded end, to ensure even distribution and eliminate air pockets. After compacting, the top surface of the concrete is leveled off.
Once the mold is filled, it is gently lifted upward, allowing the concrete to slump downward due to gravity. The decrease in height of the concrete, referred to as the slump, is then measured to the nearest quarter inch. A proper slump, where the concrete maintains its conical shape, is a true slump. If the concrete collapses or spreads out, indicating a shear slump, the test may need to be repeated as it suggests the mix lacks cohesion and could be problematic for structural applications.
Excessively high or low slump values are indicators of potential issues in the concrete mix, requiring adjustments. The slump test is particularly effective for identifying the immediate need for corrections in bulk concreting operations, although it may be less reliable for lean mixes where the concrete tends to collapse. Recommended slump values are predetermined based on the specific requirements for different types of workability.

Slump Test

The slump test measures concrete workability and uses a 12-inch high truncated cone mold, narrowing from eight inches at the base to four inches at the ...

Education

JoVE Core

Civil Engineering

Unit 1

Fresh Concrete

KEY TERMS AND CONCEPTS

concrete workability check with slump

The slump test checks the workability of fresh concrete. Workability means how easy the mix is to place and handle. The test uses a 12-inch-high truncated cone mold that narrows from eight inches at the base to four inches at the top.

Before testing, the mold is fixed to a flat base and dampened. Concrete is added in three layers. Each layer is compacted 25 times with a steel tamping rod that is five-eighths of an inch in diameter and has a rounded end. This helps spread the concrete evenly and remove air pockets. The top surface is then leveled off.

After the mold is full, it is lifted straight up. The concrete drops under gravity, and the drop in height is called the slump. The slump is measured to the nearest quarter inch. If the concrete keeps its cone shape, it is called a true slump.

If the concrete collapses or spreads out, it is a shear slump. That result can mean the mix lacks cohesion and may not work well for structural use. Very high or very low slump values also point to problems in the mix and may require adjustment. The slump test is especially useful for finding quick fixes in bulk concreting work, but it may be less reliable for lean mixes that tend to collapse. Recommended slump values are set ahead of time for the workability needed in each type of job.

Concrete Workability Check with Slump

workability of concrete

Concrete Flow and Compaction Factors

Concrete workability is the ease with which fresh concrete can be mixed, placed, compacted, and finished. It is an important property during construction because it affects how well the material moves into position and how easily it can be shaped. Workability depends on the internal friction within the mix and the resistance it meets from molds and reinforcements. When the ingredients resist one another, concrete moves less easily. The same is true when it has to pass around barriers in the...

factors affecting workability

Concrete Workability and Mix Design Factors

Concrete workability depends on mix design factors that change how easily the material can be mixed, handled, and finished. The mix needs enough flow so it can move and be placed without losing quality. Water is a key part of this because it acts as a lubricant between the ingredients. The amount of water needed can change with the aggregates, or the solid particles in the mix. Finer particles and angular, rough-textured aggregates need more water than smooth, rounded ones because they have...

segregation in fresh concrete

How Concrete Mixes Separate During Placement

Fresh concrete can separate during placement, which changes how the mix is spread and can weaken the finished structure. This separation is called segregation. It happens when the parts of the mix no longer stay evenly blended. Segregation often occurs when concrete moves too much inside a form. It can also happen when the mix is dropped from a great height or pushed through narrow paths with sharp turns. In these cases, the heavier coarse aggregate settles at the bottom, while lighter...

bleeding in fresh concrete

Bleeding Water and Laitance in Fresh Concrete

Bleeding in fresh concrete happens when water from the mix rises to the surface after placement. The solid parts of the mix do not hold all the water as they settle, so separation occurs and water collects on top. Engineers can measure the severity of bleeding by checking total settlement or by noting how much the concrete height drops per unit height. Bleeding can create weak spots inside the concrete. Rising water may get trapped under large aggregate particles or reinforcement bars, which...

The slump test checks the workability of fresh concrete. Workability means how easy the mix is to place and handle. The test uses a 12-inch-high truncated cone mold that narrows from eight inches at the base to four inches at the top. Before testing, the mold is fixed to a flat base and dampened. Concrete is added in three layers. Each layer is compacted 25 times with a steel tamping rod that is five-eighths of an inch in diameter and has a rounded end. This helps spread the concrete evenly...

compacting factor test

Concrete Workability by Compacting Factor

The compacting factor test measures the workability of concrete. Workability describes how easily concrete can move and fill a mold or form during construction. This test is especially suitable for concrete mixes with aggregates up to one and a half inches in size. The setup uses specialized equipment with two truncated cone-shaped hoppers and a cylinder. All of the inside surfaces are polished to reduce friction. Concrete is first placed into the upper hopper without any compaction. Then the...

vebe test

Concrete Workability with the Vebe Test

The Vebe test measures the workability of concrete, especially for dry mixes. Workability means how easy concrete is to handle and compact. The test uses a cylindrical chamber, a standard slump cone, and a transparent disc-shaped rider mounted on a vibrating table. The cylindrical chamber measures nine and a half inches in diameter and eight inches in height. Concrete is placed into the slump cone in layers and compacted in the standard way. After the cone is removed, the concrete stays in the...

flow table test

Concrete Spread Measured by Flow Table

The flow table test measures how far fresh concrete spreads, which helps assess workability. Workability means how easily concrete can flow and settle under its own weight. The method is useful for highly flowable concrete mixes. The test uses a flow table made from a wooden board with a steel plate on top. Together, the parts weigh 35 pounds. The board is hinged to a base and measures 27.6 inches on each side. A truncated cone mold is also used. It is 8 inches high, with an 8-inch base...

key terms and concepts

Learn how the slump test measures concrete workability using a cone mold, layered filling, tamping, and slump measurement for fresh concrete.

Concrete Workability Check with Slump | JoVE K12

JoVE Core Civil Engineering offers a foundational exploration of essential construction materials such as bricks, stones, steel, wood, and concrete, along with fluid mechanics topics like flow over immersed bodies, open channel flow, and dimensional modeling. It also covers key surveying concepts, including leveling, traverse adjustments, curve design, topographic mapping, and geospatial technologies (GPS & GIS). Science-in-action videos showcase laboratory research on materials, fluids, and surveying practices in real-world engineering systems.

civil engineering

Concrete Workability Check with Slump

Description

Transcript

Tags