Name: pipe size for laminar air flow
Uploaded: 2025-02-13T15:43:34.000Z
Duration: 1 min 24 s
Channel: JoVE

Consider air flowing through the pipe at 300 Kelvin at standard atmospheric pressure, with a mass flowrate of 0.0163 kilograms per second. If the flow is assumed to be laminar, determine the minimum diameter allowed for the pipe.
Laminar flow is achieved when the Reynolds number does not exceed 2100. This calculation begins by expressing the velocity in terms of flow rate and cross-sectional area.
For a circular pipe, the velocity depends on the flow rate and the pipe&#39;s diameter. Substituting this expression for velocity into the Reynolds number formula, which involves density, velocity, diameter, and viscosity, allows solving for the flow rate.
Given the specified flow rate, the fluid density is calculated using known values for pressure, gas constant, and temperature, yielding approximately 1.177 kilograms per cubic meter.
With the known quantities of mass flowrate and density, the volumetric flow rate is found to be around 0.0138 cubic meters per second.
Using a standard viscosity value, the required pipe diameter to ensure laminar flow is approximately 0.46 meters, keeping the Reynolds number at 2100.

laminar flow: problem solving

Laminar Flow: Problem Solving

Laminar flow occurs when a fluid moves smoothly in parallel layers with minimal mixing and turbulence. In fluid mechanics, ensuring laminar flow within a pipe is essential for precise control of flow characteristics, especially in engineering applications. The key factor in determining whether flow remains laminar is the Reynolds number, a dimensionless quantity that depends on the fluid&#39;s velocity, density, viscosity, and the pipe&#39;s diameter. A Reynolds number of 2100 or lower indicates laminar flow, while higher values lead to turbulence.
For air flowing through a pipe at standard atmospheric conditions and a given mass flow rate, the velocity of the fluid must be controlled to maintain laminar conditions. Since velocity depends on the flow rate and the cross-sectional area of the pipe, the pipe diameter plays a crucial role. By substituting the velocity expression into the Reynolds number formula and solving for the diameter, it is possible to determine the minimum required pipe size.
Using standard values for air density and viscosity at 300 Kelvin, the volumetric flow rate can be computed. This, in turn, allows for the calculation of the necessary pipe diameter. To ensure a Reynolds number of 2100 or lower, the minimum allowable diameter for the pipe is found to be approximately 0.46 meters. This calculation ensures that the flow remains smooth and predictable, avoiding turbulence that could disrupt performance.

Consider air flowing through the pipe at 300 Kelvin at standard atmospheric pressure, with a mass flowrate of 0.0163 kilograms per second. If the flow is ...

Education

JoVE Core

Civil Engineering

Unit 1

Flow in Pipes

KEY TERMS AND CONCEPTS

pipe size for laminar air flow

Laminar flow in a pipe means the fluid moves in smooth, parallel layers with very little mixing or turbulence. In fluid mechanics, keeping flow laminar is important when engineers want precise control of flow behavior. The Reynolds number is the key value used to check this. It is a dimensionless number that depends on the fluid’s speed, density, viscosity, and the pipe’s diameter.

A Reynolds number of 2100 or lower shows laminar flow. Higher values lead to turbulence. For air flowing through a pipe at standard atmospheric conditions and a fixed mass flow rate, the fluid speed must be controlled to stay in the laminar range. Because speed depends on the flow rate and the pipe’s cross-sectional area, the pipe diameter becomes the main design factor.

The calculation starts by substituting the velocity expression into the Reynolds number formula and solving for the diameter. For air at 300 Kelvin, the standard values of density and viscosity are used to find the volumetric flow rate first. That flow rate then gives the pipe size needed to keep the flow laminar. The minimum allowable diameter is about 0.46 meters, which helps the air move smoothly and predictably without turbulence that could affect performance.

Pipe Size for Laminar Air Flow

general characteristics of pipe flow i

Pipe Flow Regimes and Reynolds Number

Pipe flow is the movement of fluids through fully enclosed conduits such as water pipes and hydraulic hoses. These pipes are built to handle high-pressure gradients that drive the fluid forward. That is different from open-channel flow, where gravity is the main driving force. Rectangular conduits, such as air conditioning and heating ducts, usually work at lower pressures and are less suited for high-pressure use. Osborne Reynolds first classified pipe flow with dye injection experiments. He...

general characteristics of pipe flow ii

Pipe Entrance Length and Pressure Changes

Pipe flow changes as fluid moves from the pipe entrance to a fully developed state. At the entrance, the velocity profile is still adjusting. Viscous effects create a boundary layer along the wall, and that layer grows until it fills the whole pipe cross-section. When the boundary layer merges across the pipe, the flow becomes fully developed. At that point, the velocity profile stays steady along the pipe length. The distance needed to reach this state is called the entrance length. It...

laminar flow

Pipe Flow Patterns and Pressure Loss

Pipe flow patterns can be smooth, changing, or chaotic, and laminar flow is the smoothest form. In laminar flow, fluid particles move in parallel paths with very little mixing between layers. This happens when viscous forces are stronger than inertial forces. The flow regime in a pipe is often described with the Reynolds number, a dimensionless value that depends on fluid density, flow speed, pipe diameter, and dynamic viscosity. A Reynolds number below about 2100 usually means laminar flow.

Laminar flow in a pipe means the fluid moves in smooth, parallel layers with very little mixing or turbulence. In fluid mechanics, keeping flow laminar is important when engineers want precise control of flow behavior. The Reynolds number is the key value used to check this. It is a dimensionless number that depends on the fluid’s speed, density, viscosity, and the pipe’s diameter. A Reynolds number of 2100 or lower shows laminar flow. Higher values lead to turbulence. For air flowing through...

turbulent flow

Turbulent Flow in Pipes and Mixing

Turbulent flow is a fluid pattern with irregular changes in speed and pressure. It looks chaotic when compared with laminar flow, which moves in smooth, parallel layers with little mixing. In turbulent flow, the motion is highly irregular and three-dimensional. This behavior starts when the fluid speed becomes high enough to create instabilities in the velocity profile. Small disturbances, called turbulent spots, can appear at a critical speed. As the Reynolds number, a ratio of inertial...

turbulent flow: problem solving

Carbonation Flow and Reynolds Number

Carbonation uses carbon dioxide gas to dissolve gas into a liquid, as in carbonated drinks. Efficient carbonation depends on temperature, pressure, and flow conditions. By controlling these factors, more CO2 can dissolve in the liquid. Temperature plays a major role in CO2 solubility. Here, both the CO2 gas and the liquid are cooled to 20°C. Lower temperatures increase solubility, so a larger volume of gas can dissolve. Pressure also helps drive carbonation. At 20°C, the CO2 gas is...

major losses in pipes

Pipe Pressure Drop from Wall Friction

Pipe pressure drop from wall friction is a major loss in fluid flow. As a fluid moves through a pipe, friction along the pipe walls removes energy. That energy loss shows up as a drop in pressure. The size of the drop depends on the flow conditions and on the physical properties of both the fluid and the pipe. Flow in a pipe is often described as laminar or turbulent using the Reynolds number. This dimensionless number compares inertial forces with viscous forces in the fluid. In laminar flow,...

minor losses in pipes

Pipe Fittings and Valve Head Loss

Pipe fittings and valves can cause head loss in a pipe system. These losses happen when flow is disturbed by bends, expansions, entries, exits, and other components. The fluid loses energy because the flow becomes less steady and more turbulent. Valves are a major source of minor loss because they block or guide the fluid path. A closed valve or a partly closed valve adds resistance and creates turbulence. The amount of energy loss depends on the valve shape, its position, and the way the flow...

single pipe systems

Pipe Flow Problems by What You Know

Pipe flow problems are grouped by the information that is known and the result that needs to be found. In fluid mechanics, these are often called Type I, Type II, and Type III problems. Each type uses fluid properties, pipe details, and operating conditions to answer a different engineering question. In a Type I problem, the fluid density and viscosity are known. The pipe diameter, length, and surface roughness are also known. The flow rate or average velocity is given, and the goal is to find...

multiple pipe systems

Pipe Flow Paths in Series and Parallel

Multiple pipe systems move fluids through connected pipe paths in engineering networks. They help control flow distribution, pressure, and head loss. These systems are grouped into series, parallel, loop, and network configurations, and each one behaves differently. In a series configuration, fluid passes through one pipe segment after another. The flow rate stays the same through every segment. Head loss builds up across the path, so the total loss from entry point A to exit point B is the...

pipe flowrate measurement

Comparing Orifice, Nozzle and Venturi Meters

Orifice, nozzle, and Venturi meters are used to measure fluid flowrate in pipes by narrowing the flow area. The smaller opening makes the fluid move faster and lowers the pressure. The pressure difference, together with Bernoulli’s principle and real-world corrections, is used to calculate flowrate. The orifice meter is the simplest and least expensive option. It uses a flat plate with a hole in the center to create a measurable pressure drop. It is often used in water treatment, oil and gas...

pipe flowrate measurement: problem solving

pipe-flowrate-measurement-problem-solving

Spray Tank Pipe Flow Rate Calculation

Spray tank pipe flow rate calculation uses fluid mechanics to find how fast pesticide moves through a pressurized system. The tank is pressurized to 150 kPa and holds the liquid at a height of 0.80 meters. The liquid then travels through a 1.9 meter pipe with a diameter of 0.015 meters and an angle of 0.698 radians before reaching a 0.007 meter nozzle that sprays the pesticide. Accurate flow rate matters because the pesticide must be applied evenly across the plants. The first step is to find...

design example: designing a residential plumbing system

design-example-designing-a-residential-plumbing-system

Residential Plumbing Flow and Pressure Design

Residential plumbing flow and pressure design starts with water demand, flow rate, and pressure needs. These systems are sized by looking at how many people live in the home and what fixtures they use. The goal is to provide reliable water delivery while keeping the system efficient. A key part of the design is the Reynolds number. This dimensionless value helps classify flow in a pipe as laminar, which is smooth, or turbulent, which is more mixed and irregular. It depends on factors such as...

key terms and concepts

Find the minimum pipe diameter needed to keep air flow laminar at 300 K. Learn how Reynolds number, flow rate, and pipe size work together.

Pipe Size for Laminar Air Flow | JoVE K12

JoVE Core Civil Engineering offers a foundational exploration of essential construction materials such as bricks, stones, steel, wood, and concrete, along with fluid mechanics topics like flow over immersed bodies, open channel flow, and dimensional modeling. It also covers key surveying concepts, including leveling, traverse adjustments, curve design, topographic mapping, and geospatial technologies (GPS & GIS). Science-in-action videos showcase laboratory research on materials, fluids, and surveying practices in real-world engineering systems.

civil engineering

Pipe Size for Laminar Air Flow

Description

Transcript

Tags