Basic Organic Chemistry Techniques
Glassware in Organic Chemistry
There are standard pieces of glassware that are used in the organic chemistry lab. Beakers and Erlenmeyer flasks are ty…
Laboratory procedures in organic chemistry typically utilize standard glassware equipment and techniques. Beakers and Erlenmeyer flasks are often used for simple mixing and holding solvents. Round-bottom flasks with either a short or a long neck are used for reactions under high heat or vacuum. This is because the round shape is more resistant to cracking under these conditions.
Heating reactions is a common lab procedure. However, a Bunsen burner is not generally used for organic compounds because they are flammable. When heating a reaction in a beaker or Erlenmeyer flask, a hot plate with a magnetic stirrer is typically used. When heating a reaction in a round-bottom flask, a water bath or heating mantle is used to accommodate the shape of the flask.
Many reactions must be heated to a certain temperature for a specific amount of time to proceed. These reactions are performed under reflux. A reflux setup uses a round-bottom flask containing a solvent whose boiling point overlaps with the optimal temperature of the reaction. A condenser is fitted onto the flask, and cold water enters at the bottom arm and exits out the top arm. As the mixture is heated and stirred, the solvent evaporates and then condenses back into the flask, preserving the reaction volume.
Another common technique used in the organic chemistry lab is filtration, which is a method to separate solids from liquids. Gravity filtration is the simplest filtration technique used to separate granular insoluble solids. This setup consists of an Erlenmeyer flask, a conical funnel, and a folded piece of filter paper. The mixture is poured into the funnel, and the liquid passes through into the flask, called the filtrate. The solids remain on the filter paper.
A faster filtration technique is vacuum filtration. Here, a Büchner funnel is connected to a filter flask using a rubber adaptor. The filter flask looks like an Erlenmeyer flask, but it has a side arm that connects the flask to the vacuum via vacuum tubing. Then, a flat piece of filter paper is placed inside of the funnel and wet slightly before the vacuum is slowly turned on. The liquid is sucked through the filter paper into the flask, while the solid is retained on the filter paper.
In this lab, you will perform a simple reaction to form benzoic acid, enabling you to practice simple organic chemistry techniques, like weighing solids, measuring volume, and performing vacuum filtration. You'll then practice the reflex technique using tetrahydrofuran.
Laboratory procedures in organic chemistry typically utilize standard glassware equipment and techniques. Beakers and Erlenmeyer flasks are often used for simple mixing and holding solvents. Round-bottom flasks with either a short or a long neck are used for reactions under high heat or vacuum. This is because the round shape is more resistant to cracking under these conditions.
Heating reactions is a common lab procedure. However, a Bunsen burner is not generally used for organic compounds because they are flammable. When heating a reaction in a beaker or Erlenmeyer flask, a hot plate with a magnetic stirrer is typically used. When heating a reaction in a round-bottom flask, a water bath or heating mantle is used to accommodate the shape of the flask.
Many reactions must be heated to a certain temperature for a specific amount of time to proceed. These reactions are performed under reflux. A reflux setup uses a round-bottom flask containing a solvent whose boiling point overlaps with the optimal temperature of the reaction. A condenser is fitted onto the flask, and cold water enters at the bottom arm and exits out the top arm. As the mixture is heated and stirred, the solvent evaporates and then condenses back into the flask, preserving the reaction volume.
Another common technique used in the organic chemistry lab is filtration, which is a method to separate solids from liquids. Gravity filtration is the simplest filtration technique used to separate granular insoluble solids. This setup consists of an Erlenmeyer flask, a conical funnel, and a folded piece of filter paper. The mixture is poured into the funnel, and the liquid passes through into the flask, called the filtrate. The solids remain on the filter paper.
A faster filtration technique is vacuum filtration. Here, a Büchner funnel is connected to a filter flask using a rubber adaptor. The filter flask looks like an Erlenmeyer flask, but it has a side arm that connects the flask to the vacuum via vacuum tubing. Then, a flat piece of filter paper is placed inside of the funnel and wet slightly before the vacuum is slowly turned on. The liquid is sucked through the filter paper into the flask, while the solid is retained on the filter paper.
In this lab, you will perform a simple reaction to form benzoic acid, enabling you to practice simple organic chemistry techniques, like weighing solids, measuring volume, and performing vacuum filtration. You'll then practice the reflex technique using tetrahydrofuran.
View the full transcript and gain access to JoVE Lab Manual videos
Q1: Why are round-bottom flasks preferred for heating organic reactions?
Round-bottom flasks are preferred for high-heat or vacuum reactions because their round shape is more resistant to cracking than flat-bottomed glassware. The curved design also provides more surface area for uniform heating or cooling. This makes them ideal for reactions requiring sustained temperature control or pressure changes.
Q2: What is reflux and why is it used in organic chemistry?
Reflux is a technique that prevents solvent loss during prolonged heating. A condenser fitted to a round-bottom flask allows heated solvent vapors to condense and return to the flask, preserving reaction volume. Cold water flows through the condenser from bottom to top while the mixture is heated and stirred, maintaining optimal reaction temperature without evaporative loss.
Q3: What is the difference between gravity filtration and vacuum filtration?
Gravity filtration uses a simple setup with a glass funnel and filter paper, relying on gravity to separate solids from liquids. Vacuum filtration is faster and uses a Büchner funnel connected to a vacuum flask with a side arm. The vacuum applies suction to pull liquid through the filter paper more quickly, making it ideal for time-sensitive lab work.
Q4: Why shouldn't Bunsen burners be used to heat organic compounds?
Organic compounds and solvents are highly flammable and readily form combustible vapors. An open flame from a Bunsen burner creates a dangerous fire hazard in organic chemistry labs. Instead, indirect heating methods like hot plates, heating mantles, and water baths provide safe temperature control without flame exposure.
Q5: How should you properly weigh solid organic reagents in the lab?
Place a weighing boat or paper on an analytical or top-loading balance and press tare to zero the mass. Use a spatula to transfer solid from the stock bottle to the weighing boat. Never reuse the same spatula for different reagents to avoid contamination, and never return excess reagent to the stock bottle.
Q6: What heating method should be used for reactions requiring temperatures above 100°C?
For temperatures between 100°C and 250°C, use a silicone heating mantle designed for round-bottom flasks to provide uniform, indirect heat. For temperatures exceeding 250°C, use a sand bath instead. Heating mantles and sand baths are safer than open flames for organic reactions requiring high temperatures.
Q7: What is the purpose of using the smallest appropriate graduated cylinder for volume measurement?
Using the smallest graduated cylinder suitable for your volume minimizes measurement error. For example, a 25-mL cylinder accurately measures 20 mL but cannot precisely measure 5 mL. Conversely, do not use a 25-mL cylinder four times to measure 100 mL; instead, use a 100-mL graduated cylinder for better accuracy.