An Improved Method for the Preparation of Type I Collagen From Skin

Summary

Traditional procedures for the isolation of soluble type 1 collagen (COL1) require about 10 days from start to finish because of lengthy buffer incubations and laborious resuspensions of fibrils. Here, we describe a means to purify COL1 from small dermal biopsies in less than 3 hr.

Abstract

Soluble type 1 collagen (COL1) is used extensively as an adhesive substrate for cell cultures and as a cellular scaffold for regenerative applications. Clinically, this protein is widely used for cosmetic surgery, dermal injections, bone grafting, and reconstructive surgery. The sources of COL1 for these procedures are commonly nonhuman, which increases the potential for inflammation and rejection as well as xenobiotic disease transmission. In view of this, a method to efficiently and quickly purify COL1 from limited quantities of autologously-derived tissues would circumvent many of these issues; however, standard isolation protocols are lengthy and often require large quantities of collagenous tissues. Here, we demonstrate an efficient COL1 extraction method that reduces the time needed to isolate and purify this protein from about 10 days to less than 3 hr. We chose the dermis as our tissue source because of its availability during many surgical procedures. This method uses traditional extraction buffers combined with forceful agitation and centrifugal filtration to obtain highly-pure, soluble COL1 from small amounts of corium. Briefly, dermal biopsies are washed thoroughly in ice-cold dH₂O after removing fat, connective tissue, and hair. The skin samples are stripped of noncollagenous proteins and polysaccharides using 0.5 M sodium acetate and a high speed bench-top homogenizer. Collagen from residual solids is subsequently extracted with a 0.075 M sodium citrate buffer using the homogenizer. These extracts are purified using 100,000 MW cut-off centrifugal filters that yield COL1 preparations of comparable or superior quality to commercial products or those obtained using traditional procedures. We anticipate this method will facilitate the utilization of autologously-derived COL1 for a multitude of research and clinical applications.

Introduction

For decades, researchers and commercial vendors have isolated solubilized COL1 from an assortment of tissue sources including skin and tendon using some variation of a simple acid extraction protocol followed by neutralization, which results in a resuspension of a matrix of organized COL1 fibrils that can be used for a multitude of biomedical applications ^1-4.  While there are many examples of clinical applications for COL1, few of these employ autologously-derived COL1 because preparation of this protein requires lengthy extractions taking days or weeks to perform^5-7. As a result, research investigators and physicians generally use expensiv....

Protocol

Here we will demonstrate the isolation of COL1 from lamb skin.  As written, this protocol can also be used to successfully isolate COL1 from rabbit and human skin.

1. Prepare Dermal Sample

1. Equilibrate all reagents to 4 °C prior to use.
2. Rinse dermal sample (25-50 g) in ice-cold dH₂O and remove any wool, fur, or hair with depilatory cream.
3. Use a single-edge razor blade to scrape the sample clean of connective tissue and fat.
4. Rinse the sample in ice-cold dH₂O.
5. Slice the skin sample into 1 cm x 1 cm pieces with a single-edge razor blade.

Results

This COL1 isolation protocol requires about 2 hr and 15 min to complete. Figure 1 shows a schematic diagram outlining the major steps in this procedure. Preparing the sample and performing the 7 cycles of high-speed agitations and rinses with sodium acetate takes approximately 35 min (Figures 1A-C). Performing one agitation and rinse cycle with dH₂O takes approximately 5 min (Figures 1D and 1E). Adding sodium citrate and subjecting the sample to one agitation .......

Discussion

A crucial component to this method is the repeated efficient compression of the dermal sample to remove excess liquid. It is critical to remove as much sodium acetate as possible in step 2.5 by compressing the sample. We use a spatula to compact the skin against the side of the tube; however, cheesecloth could also be used, although this would necessitate removal of the sample from the tube and increase the time required to perform these steps. Likewise, it is important to compress the sample in step 3.1 so that the volu.......

Materials

List of materials used in this article

Name	Company	Catalog Number	Comments
FastPrep-24 System	MP Biomedicals	116004500
Centrifuge	Beckman	J6-MI	Swing bucket rotor to accommodate 50 ml conical tubes at 3,200 x g.