Solvent Assisted Linker Exchange
Solvent Assisted Linker Exchange - Related Videos
09:38
Biomembrane Fabrication by the Solvent-assisted Lipid Bilayer (SALB) Method
0 Views •
Cited by 23 •
2015
We present an experimental protocol to form a supported lipid bilayer on solid substrates without using lipid vesicles. We demonstrate a one-step method to form a lipid bilayer on silicon dioxide and gold as well as supported membranes with cholesterol-enriched domain for various biological applications.
08:13
Preparation of Biopolymer Aerogels Using Green Solvents
0 Views •
Cited by 45 •
2016
A new way for the production of biopolymer-based aerogels by carbon dioxide (CO2) induced gelation is shown. The technique utilizes pressurized carbon dioxide (5 MPa) for the production of biopolymer hydrogels and supercritical CO2 (12 MPa) to convert gels into aerogels. The only solvents needed besides CO2 are water and ethanol.
06:43
Rotary Evaporation to Remove Solvent
0 Views •
2023
Source: Dr. Melanie Pribisko Yen and Grace Tang — California Institute of Technology Rotary evaporation is a technique most commonly used in organic chemistry to remove a solvent from a higher-boiling point compound of interest. The rotary evaporator, or "rotovap", was invented in 1950 by the chemist Lyman C. Craig. The primary use of a rotovap is to dry and purify samples for downstream applications. Its speed and ability to handle large volumes of solvent make rotary evaporation a preferred...
09:41
Schlenk Lines Transfer of Solvents
0 Views •
2023
Source: Hsin-Chun Chiu and Tyler J. Morin, laboratory of Dr. Ian Tonks—University of Minnesota Twin Cities Schlenk lines and high vacuum lines are both used to exclude moisture and oxygen from reactions by running reactions under a slight overpressure of inert gas (usually N2 or Ar) or under vacuum. Vacuum transfer has been developed as a method separate solvents (other volatile reagents) from drying agents (or other nonvolatile agents) and dispense them to reaction or storage vessels while...
11:38
Heat Exchanger Analysis
0 Views •
2023
Source: Alexander S Rattner and Christopher J Greer; Department of Mechanical and Nuclear Engineering, The Pennsylvania State University, University Park, PA Heat exchangers transfer thermal energy between two fluid streams, and are ubiquitous in energy systems. Common applications include car radiators (heat transfer from hot engine coolant to surrounding air), refrigerator evaporators (air inside refrigerator compartment to evaporating refrigerant), and cooling towers in power plants...
FAQs
Incoming linker molecules diffuse through the solvent and reach coordination sites at the MOF metal nodes. Reversible coordination allows these molecules to interact with the nodes while the original ligands are displaced. Because the framework can remain largely intact during this exchange, the method modifies the MOF’s chemistry without requiring complete reconstruction of its structural network.
Solvent choice, temperature, linker concentration, and framework stability strongly influence exchange. Solvent affects how readily molecules diffuse through the framework, while temperature and concentration can change the exchange rate and amount of replacement. The framework must also tolerate the treatment, because its stability determines how successfully modification occurs while preserving the underlying structure.
Reversible coordination provides a dynamic pathway for incoming and original linkers to interact with metal nodes. Bonds can form and break during treatment, allowing ligand displacement rather than requiring permanent disruption of the framework. This behavior is central to controlled post-synthetic modification, since it supports chemical tuning while helping retain the MOF architecture.
A researcher begins with a preformed MOF and places it in a solution containing the desired linker molecules. The selected solvent provides the medium for diffusion, while temperature and linker concentration are adjusted according to the framework’s stability and the intended exchange extent. After exposure, the treated material contains modified linker chemistry within the existing MOF structure.
Researchers can use this approach when they want to tune an existing MOF’s pore size, chemical functionality, stability, or adsorption behavior without rebuilding the framework from the beginning. The post-synthetic route is especially relevant when the original architecture is valuable and the desired modification can be achieved through controlled linker exchange at the metal nodes.
Linker exchange can adjust pore size and chemical functionality, which in turn supports changes in stability and adsorption behavior. These tunable properties make the method relevant to MOF research in catalysis, separations, sensing, and gas storage. Its value lies in connecting molecular-level ligand modification with application-specific performance of the porous material.