19.3
Dairesel Mil - Doğrusal Aralıkta Gerilim
Dairesel bir şaftın Hooke Yasası sınırları dahilinde kalan torka maruz kaldığı ve herhangi bir kalıcı deformasyonun önlendiği bir senaryo düşünün. Bu…
Dairesel mile uygulanan torkun Hooke yasası sınırı içinde olduğu, dolayısıyla kalıcı bir deformasyon olmadığı bir durumu düşünün.
Şimdi, kesme gerilimi ifadesini hatırlayın. Rijitlik modülü ile çarpılarak ve kesme gerilimi ve gerinim için Hooke Yasası kullanılarak, bir şafttaki kesme gerilimi için bir ifade belirlenebilir.
Şaftın herhangi bir enine kesitine uygulanan temel kuvvetlerin momentlerinin toplamının, şaft üzerine uygulanan torkun büyüklüğüne eşit olması gerektiğini hatırlayın.
Kesme geriliminin yerine geçmek ve terimleri yeniden düzenlemek, enine kesitin merkezine göre kutupsal atalet momentini temsil eden integral bir terimle bir ifade verir.
Maksimum kesme gerilimi için daha fazla yeniden düzenleme ve ikame, rijit bir tekdüze dairesel şaftta kesme gerilimi için elastik burulma formülünü verir.
Bununla birlikte, iç ve dış yarıçapları r1 ve r2 olan içi boş bir şaft için, kutupsal atalet momenti, iki yarıçapın dördüncü kuvvetindeki bir fark olarak ifade edilir.
View the full transcript and gain access to JoVE Core videos
Q1: What is the elastic torsion formula for shearing stress in a circular shaft?
The elastic torsion formula determines shearing stress in a rigid uniform circular shaft by combining Hooke's Law with the polar moment of inertia. It derives from multiplying shearing strain by the modulus of rigidity, then ensuring the sum of moments on any cross-section equals the applied torque. This formula applies when torque remains within Hooke's law limit, preventing permanent deformation.
Q2: How does the polar moment of inertia differ between solid and hollow circular shafts?
For a solid circular shaft, the polar moment of inertia is calculated from the fourth power of the radius. For a hollow shaft with inner radius r1 and outer radius r2, the polar moment of inertia is expressed as the difference in the fourth power of both radii. This difference accounts for the removed material in the hollow center.
Q3: Why is the modulus of rigidity important in deriving shaft stress equations?
The modulus of rigidity relates shearing stress to shearing strain through Hooke's Law. When multiplied by the shearing strain expression, it enables derivation of the shearing stress equation for the shaft. This material property is essential for connecting elastic deformation behavior to the applied torque.
Q4: What role does the sum of moments play in the elastic torsion formula?
The sum of moments of elementary forces exerted on any cross-section of the shaft must equal the magnitude of the applied torque. This equilibrium condition is fundamental to deriving the elastic torsion formula. Substituting this relationship into the stress equation produces the integral term representing polar moment of inertia.
Q5: When can the elastic torsion formula be applied to a circular shaft?
The elastic torsion formula applies when torque remains within Hooke's law limit, ensuring no permanent deformation occurs. Under these conditions, the shaft exhibits linear elastic behavior, and shearing stress is directly proportional to shearing strain. This linear range assumption is critical for formula validity.
Q6: How does maximum shearing stress relate to the polar moment of inertia in torsion?
Maximum shearing stress is inversely proportional to the polar moment of inertia. After substituting for maximum shearing stress in the equilibrium equation, the polar moment of inertia emerges as a key geometric property. Larger polar moments of inertia reduce maximum stress for the same applied torque, which is why hollow shafts are often preferred in design of transmission shafts.
Q7: What assumptions must be satisfied for the elastic torsion formula to hold?
The shaft must be rigid and uniform with constant cross-section. Torque must remain within Hooke's law limit to prevent plastic deformation. The formula assumes linear elastic material behavior where shearing stress is proportional to shearing strain. These conditions ensure the derived relationships between torque, stress, and geometric properties remain valid.