11.11
Kırpıcı Devreler
Kırpıcı devre, dalga biçimi özelliklerini değiştirmek ve kontrol etmek için diyotların benzersiz özelliklerinden yararlanan temel bir dalga şekillendi…
Kesme devresi, dalga biçimlerini değiştirmek için diyotlar kullanan bir dalga şekillendirme aracıdır.
Bu devreler TV'lerde, radar vericilerinde ve alıcılarda yaygındır.
Her biri bir önyargılı pile bağlı iki ideal diyottan ve bir dirençten oluşan çift kesme devresi düşünün.
Giriş AC sinyalinin pozitif yarım döngüsü sırasında, diyot D1, giriş sinyali tarafından ileri kutupludur ve önyargılı pil tarafından ters kutupludur. Buna karşılık, diyot D2 her ikisi tarafından da ters kutupludur.
Giriş voltajı kutuplama voltajından düşükse, diyot D1 açık bir anahtar görevi görür ve çıkışın aynı uygulanan voltajı yansıtmasına neden olur.
Bununla birlikte, giriş voltajı kutuplama voltajını aştığında, diyot D1 ileri yönlü hale gelir, giriş voltajını bloke eder ve çıkışta sinyal bırakmaz.
Negatif yarım döngü için, diyot D2'nin sinyali kırpması ve çıkış voltajının D2'nin kutuplama voltajı ile sınırlandırılması ile benzer bir işlem meydana gelir.
Direnç değeri, yeterli ileri diyot akımını ve ters diyot akımından minimum voltaj düşüşünü dengelemek için titizlikle seçilir.
View the full transcript and gain access to JoVE Core videos
Q1: What is a clipper circuit and what is its primary function?
A clipper circuit is a wave-shaping tool that uses diodes to modify waveforms by removing or limiting portions of an AC signal. These circuits are commonly found in TVs, radar transmitters, and receivers, where they enhance waveform modulation. The circuit operates by allowing signals below a threshold voltage to pass while blocking or clipping signals that exceed the biasing voltage set by the circuit's batteries.
Q2: How does a dual-clipper circuit control the positive half-cycle of an input signal?
During the positive half-cycle, diode D1 responds to the input voltage relative to its biasing battery. When input voltage is less than the biasing voltage, D1 acts as an open switch, allowing the applied voltage to pass through unchanged. When input voltage exceeds the biasing voltage, D1 becomes forward-biased and blocks the signal, clipping the output to the biasing voltage level.
Q3: What happens during the negative half-cycle in a dual-clipper circuit?
During the negative half-cycle, diode D2 performs the clipping function while D1 remains reverse-biased by both the input signal and its biasing battery. Diode D2 clips the negative portion of the waveform, constraining the output voltage to the biasing voltage level of D2. This symmetrical operation ensures the output waveform is limited on both positive and negative peaks.
Q4: Why is resistor selection critical in a clipper circuit design?
The resistor value must balance two competing requirements: ensuring adequate forward current flows through the diode when it conducts, and minimizing voltage drop caused by reverse current flow when the diode is reverse-biased. This careful selection maintains proper clipping action while preserving circuit performance and preventing excessive power dissipation across the resistor.
Q5: How do ideal diodes behave in a clipper circuit configuration?
Ideal diodes in a clipper circuit act as perfect switches: they conduct with zero resistance when forward-biased and block all current when reverse-biased. This ideal behavior allows the circuit to precisely clip waveforms at predetermined voltage levels set by the biasing batteries, with no voltage drop across the conducting diode or leakage current through the reverse-biased diode.
Q6: What determines the clipping voltage level in a dual-clipper circuit?
The clipping voltage level is determined by the biasing battery voltage connected to each diode. When the input signal exceeds the biasing voltage, the corresponding diode becomes forward-biased and clips the output to that battery voltage. By selecting different battery voltages for D1 and D2, designers can independently control the positive and negative clipping thresholds of the output waveform.
Q7: How does a clipper circuit differ from other wave-shaping applications?
A clipper circuit specifically removes or limits signal portions that exceed preset voltage thresholds, creating a flattened waveform. Unlike rectifier circuits that convert AC to DC, or a clamper circuit that shifts waveform levels, clippers preserve the waveform shape while constraining its amplitude. This makes them ideal for protecting circuits from overvoltage and controlling signal peaks in communication systems.