Concentration Dependence

Source: Smaa Koraym at Johns Hopkins University, MD, USA

1. Preparation of SolutionsExpand

   Here, we show the preparation of solutions for 10 students working in pairs, with some excess. Please adjust quantities as needed.

   • Put on a lab coat, splash-proof safety glasses, and nitrile gloves. Obtain a waste container for aqueous sodium thiosulfate in advance. Note: HCl is toxic and highly corrosive, and sodium thiosulfate is an irritant, so the solutions for this lab must be prepared in a fume hood.
   • Prepare 750 mL of 0.2 M sodium thiosulfate. Weigh 37.227 g of sodium thiosulfate pentahydrate (Na₂S₂O₃·5H₂O) on a top-loading balance and pour it into a 1-L Erlenmeyer or volumetric flask through a powder funnel.
   • Rinse with water to transfer residual material into the flask. Then, use a graduated cylinder to measure out and add 600 mL of deionized water to the flask.
   • Place a magnetic stir bar in the flask and stir the solution on a large stir plate until the solution appears homogeneous.
   • Use a graduated cylinder to add another 150 mL of deionized water to the flask and continue stirring.
   • While the solution stirs, label a 750-mL bottle as ‘0.2 M sodium thiosulfate’.
   • Once the solution again appears homogeneous, turn off the stir motor. Retrieve the stir bar and transfer the solution to the bottle. Cap the bottle and store it in a central fume hood.
   • Prepare 350 mL of 6 M HCl. Measure 174 mL of 12.1 M HCl using a graduated cylinder and pour it into a 500-mL Erlenmeyer flask via a funnel.
   • Use a different graduated cylinder to measure 176 mL of deionized water and slowly add the water to the flask. Place another large magnetic stir bar in the flask and stir the solution until it appears homogeneous.
   • While the mixture stirs, label a 500-mL bottle as ‘6 M HCl’. Once the solution appears well mixed, turn off the stir motor and retrieve the stir bar.
   • Carefully pour the 6 M HCl solution into the bottle via a funnel, cap the bottle, and store it in the instructor's hood. Put away the concentrated HCl and the sodium thiosulfate.
   • Neutralize any acid waste and clean your glassware according to your lab's standard policies.
2. Preparation of the LaboratoryExpand
   • Fill a 250-mL wash bottle with deionized water and place it near the sodium thiosulfate waste container.
   • Laser print X's on paper and apply one 'X' label to the lower half of a test tube for each group. Tape the labels so that the ‘X’ is facing inward.
   • Set out the following glassware and equipment at each fume hood (we suggest that students work in pairs):

     1Stir plate with support stand

     1Medium 3-prong clamp (or test-tube clamp)

     1Thermometer clamp

     1Labeled test tube

     1Small magnetic stir bar

     150-mL beaker

     1100-mL beaker

     1600-mL beaker

     250-mm watch glasses

     110-mL graduated cylinder

     120-mL volumetric flask

     110-mL volumetric pipette

     15-mL volumetric pipette

     1Volumetric pipette dispenser

     1Test tube brush

     1Glass thermometer

     1Timer or stopwatch

     1Pair of long forceps

     1Roll of lab tape with pen

     1Package of pH paper

     1Pair of scissors

   • Put a roll of plastic paraffin film and a pair of scissors in a central location. Distribute baking soda and disposable plastic pipettes so that all students have access to them.
   • Just before the lab, place the bottle of 6 M HCl in the central fume hood. Note: Sulfur dioxide gas will still be evolving from the collected product mixtures at the end of the lab. The students will leave the neutralized waste in the fume hoods overnight.
   • The next day, at least 12 hours later, flush the liquid from the waste down the drain and put the solid sulfur and baking soda in the lab trash.