Name: Measuring Biomolecular DSC Profiles with Thermolabile Ligands to Rapidly Characterize Folding and Binding Interactions (Video) | JoVE Journal
Uploaded: 2017-11-21T12:30:00.000+00:00
Duration: 9 min 15 s
Description: Learn differential scanning calorimetry for biomolecular folding and binding interactions using thermolabile ligands. This protocol enables rapid extraction of thermodynamic parameters with minimal experiments.

ai_agent_IP

ai_agent

maintenance

instantTrialDurationMinutes

isBiopharma

enableNewMyJoveSectionDesign

educationFeatures

seoMetaApi

ai_copilot_institution_blacklist

ai_chat_institution_blacklist

freeAccessWindow

ssoRoleCapture

scheduledMaintenanceBanner

joveLabsFeatures

disable_autoplay_for_bots

extended_trial_duration

5 minutes

R. W. H. V was supported by the McGill Natural Sciences and Engineering Research Council of Canada (NSERC) Training Program in Bionanomachines. A. K. M. and P. E. J. were supported by NSERC grants 327028-09 (A. K. M) and 238562 (P. E. J.).

1. Sample Preparation
<ol>
	<li>Purify the desired biomolecule13. 
	NOTE: This protocol uses purchased cocaine-binding DNA aptamer MN4 after exchanging against 2 M NaCl three times followed by three rounds of deionized water using a centrifugal filter with a 3 kDa molecular weight cut-off membrane.</li>
	<li>Synthesize and purify, or purchase the desired thermolabile ligand13. 
	NOTE: MN4 binds the thermolabile ligand cocaine. MN4 also binds quinine, which is used as a negative control for ligand thermolability at these experimental temperatures.</li>
	<li>Prepare buffers for dialysis of the purified biomolecule and dissolution of ligands (20 mM sodium phosphate and 140 mM NaCl buffer, pH 7.4, for MN4 and the ligands used here).</li>
	<li>Dialyze the biomolecule against at least 2 L of buffer using dialysis tubing with 0.5 - 1.0 kDa cut-off.</li>
	<li>Filter the final buffer (referred to as working buffer) through a 0.2 &#181;m filter that has been thoroughly equilibrated with buffer.</li>
	<li>Weigh out the desired masses of the ligands and dissolve them in filtered working buffer. If the desired ligand concentrations require masses that are too small to accurately weigh, make a concentrated ligand stock solution (10x for example). 
	NOTE: It is crucial that all DSC experiments utilize the same working buffer for the sample and ligand, i.e., never perform an experiment where the ligand is dissolved in a different batch of working buffer than the biomolecule as this will cause buffer mismatch artifacts in the data.</li>
	<li>Filter the biomolecule stock solution through a 0.2 &#181;m filter that has been thoroughly equilibrated with working buffer.</li>
	<li>Determine the biomolecule concentration by absorbance measurements (260 nm for nucleic acids like MN4 and 280 nm for proteins).</li>
	<li>Store the prepared biomolecule and ligand in a 4 &#176;C refrigerator (suitable for MN4 and the ligands used here), or at -20 or -80 &#176;C if the biomolecule and ligands tolerate freezing and long-term storage is required. Degas the buffer, biomolecule, and ligand solutions in a table top degasser (see Table of Materials) prior to loading into the DSC. 
	NOTE: Degassing helps to prevent bubble formation in the DSC at higher temperatures. Bubbles cause signal artifacts that obscure DSC peak shapes and baselines.</li>
</ol>
2. DSC Preparation
<ol>
	<li>Unscrew the pressure handle from the DSC (see Table of Materials).</li>
	<li>Run silicon tubing from the working buffer and attach it to the front flange (metal opening) of the reference capillary.</li>
	<li>Create a bridge between the reference and sample capillaries by connecting the rear reference flange to the front sample flange.</li>
	<li>Attach a piece of silicon tubing to the rear sample flange that runs to a waste flask with a vacuum line attached.</li>
	<li>Turn on the vacuum line to flush the DSC with 200 mL of working buffer.</li>
	<li>Load the reference capillary of the DSC with working buffer. Attach roughly 3 - 5 cm sections of silicon tubing to the reference capillary flanges.</li>
	<li>Insert a 1 mL pipette tip into the rear flange&#39;s silicon tubing. Draw 0.8 mL of working buffer with a pipette and insert the pipette tip with buffer into the front reference flange&#39;s silicon tubing.</li>
	<li>Gently press the pipette plunger down to pass the working buffer through the front silicon tubing into the reference capillary and up into the rear flange&#39;s attached pipette tip. Press down the pipette plunger until the working buffer level reaches just above the front silicon tubing, then release the pipette plunger until the working buffer level reaches just above the rear silicon tubing.
	<ol>
		<li>Repeat passing the working buffer back and forth to purge the volume in the reference capillary of bubbles. 
		NOTE: Usually, 10 passes of the solution back and forth are sufficient to clear any bubbles.</li>
	</ol>
	</li>
	<li>Cap the rear pipette tip with the thumb and gently pull up on the rear pipette tip and front pipette to remove them from the reference flanges with the silicon tubing attached.</li>
	<li>Load the sample capillary with working buffer as in steps 2.6 - 2.9. Place a black plastic cap on the rear reference and sample flanges, leaving the front flanges uncovered.</li>
	<li>Attach the pressure handle.</li>
	<li>Open the DSC software (see Table of Materials) and pressurize the instrument by clicking the red up arrow at the top of the interface once the power reading has stabilized; the DSC power is indicated in a box at the top right of the interface along with the instrument temperature and pressure reading. 
	NOTE: Monitor the power reading as the DSC pressurizes. Changes in power of more than ~ 10 &#181;W indicate bubble formation in the capillaries, which can cause artifacts in the data. The solutions must be removed and degassed further before continuing.</li>
	<li>Equilibrate the DSC with working buffer by performing a forward and reverse scan. In the &#34;Experimental Method&#34; tab on the left side of the screen, ensure that the &#34;Scanning&#34; option is selected to run the DSC in temperature scanning mode. 
	NOTE: Experimental parameters are the temperature scanning range, scan rate, low and high temperature equilibration time, and number of scans.
	<ol>
		<li>In the &#34;Temperature Parameters&#34; inset under the &#34;Experimental Method&#34; tab, click the button for &#34;Heating&#34;. Enter 1 and 100 &#176;C for the lower and upper experimental temperatures, 1 &#176;C/min for the scan rate, and 60 s for the equilibration period.</li>
		<li>Click the &#34;Add Series&#34; button under the input field for the equilibration period. Enter 2 into the &#34;Steps to add&#34; field in the popup window (for one heating and one cooling scan) and check the &#34;Alternate Heating/Cooling&#34; box. Click &#34;OK&#34;; the added scans appear in the lower portion of the interface. Check that the parameters for each scan are as desired.</li>
		<li>Start the experiment by clicking the green &#34;play&#34; button at the top of the interface. Navigate to the desired folder and input a file name for saving the experiment in the popup window. View the experiment progress by clicking the &#34;Data&#34; tab to the right of the &#34;Experiment Method&#34; tab.</li>
	</ol>
	</li>
</ol>
3. Collecting Thermolabile Ligand DSC Datasets
NOTE: The minimal procedure consists of five experiments: buffer reference experiments with and without ligand (used for baseline subtraction, see Discussion), sample experiments with the free biomolecule, the ligand-bound biomolecule, and the ligand-bound biomolecule with a longer high temperature equilibration period.
<ol>
	<li>Run reference experiments for baseline subtraction of the sample data. Reload the DSC with working buffer in both capillaries and collect multiple forward and reverse scans over a suitable temperature range at 1 &#176;C min-1 with an upper (high temperature) equilibration time of 120 s.
	<ol>
		<li>Delete the previous buffer equilibration scans from the lower portion of the interface by highlighting each individually and clicking the red X to the middle right of the interface. Add the new scans by clicking the &#34;Add Series&#34; button, entering 20 in the field for &#34;Steps to add&#34;, and checking the &#34;Alternate Heating/Cooling&#34; box. Click OK and run the experiment by clicking the green play button as above.</li>
		<li>Repeat steps 3.1 - 3.1.1 with working buffer containing the desired concentration of ligand in both capillaries to obtain the reference experiments for the ligand (collect two separate experiments using 120 s and 600 s high temperature equilibration times respectively, to be used in acquiring the rate constant for thermolabile ligand conversion). 
		NOTE: The scan rate used here ensures that the biomolecule in subsequent experiments is at thermal equilibrium in the forward and reverse scans (see Discussion). Scan rates &#60; 0.1 - 0.2 &#176;C min-1 lead to noisy thermograms and are not applicable in DSC experiments. The temperatures should extend from well below the melting temperature of the free biomolecule to well above the melting temperature of ligand-saturated biomolecule (~ 20 - 80 &#176;C for MN4). Verify reproducibility of the scans (for example, 10 forward and 10 reverse scans for 20 total is sufficient).</li>
		<li>If using multiple ligands (such as cocaine and quinine), flush the DSC with 200 mL of working buffer (repeat from&#160;step 2.5) between runs in order to remove ligand from the capillaries and prevent cross-contamination. 
		NOTE: It is helpful to perform a replicate experiment on the free biomolecule after a ligand-bound run in order to check if the previous ligand adsorbs strongly to the capillary walls and is not adequately removed with buffer flushing. If the thermograms for the free biomolecule appear to be shifted to a larger magnitude and higher denaturation temperature after the ligand-bound experiment, it is likely that the previous ligand is still present in the calorimeter after flushing. Remove the adsorbed ligand by incubating the capillaries with 20% Contrad-70 for 1 h at 60 &#176;C with the plastic caps and pressure handle off. In the DSC software, change the experimental mode to &#34;Isothermal&#34; under the Experimental Method tab. Choose 3,600 s for the duration and 60 &#176;C for the isothermal temperature, with zero entered for the equilibration time. Click &#34;Add to Experimental Method&#34;. The isothermal experiment appears in the lower part of the screen. After completion, flush the instrument with 2 L deionized water and repeat from step 2.5.</li>
	</ol>
	</li>
	<li>Run sample experiments using the same DSC loading procedure and experimental parameters as the reference scans. For the free biomolecule data set, ensure that the reference capillary contains the working buffer while the sample capillary contains the free biomolecule at the desired concentration in working buffer.
	<ol>
		<li>For the ligand-bound experiments, ensure that the ligand is in the working buffer in the reference capillary, and the biomolecule plus ligand are in working buffer in the sample capillary. Flush the system between additions of different ligands as in step 2.5.</li>
	</ol>
	</li>
	<li>Perform one additional experiment with the biomolecule bound to the thermolabile ligand where the high temperature equilibration period is increased to 600 s and all other experimental parameters are the same as step 3.2.1. 
	NOTE: The duration of the high temperature equilibration period for the second ligand-bound experiment is simply chosen to ensure that the ligand is more rapidly depleted than the short equilibration time experiment. If the ligand-bound peaks from the first experiment decay slowly as a function of scan number (e.g., the differences in successive peak maxima are &#8804; 0.5 &#176;C), estimate 10- to 20-fold increases in the high temperature equilibration period in order to adequately deplete the ligand during the second experiment. The accurate calculation of the rate constant for ligand conversion requires that the second experiment has swifter depletion of the ligand relative to the first. The ligand concentrations extracted from the global analysis of the two experiments will be similar and therefore unusable if the ligand depletion is not sufficiently accelerated in the second experiment.</li>
</ol>
4. Data Processing
<ol>
	<li>Open the DSC experiment files in the DSC data analysis software (see Table of Materials) and export the raw power data as spreadsheets.</li>
	<li>Import the spreadsheets containing the raw power data into software for data fitting.</li>
	<li>Baseline subtract the sample data by subtracting the buffer power data from the free and ligand-bound biomolecule experiments. 
	NOTE: For the thermolabile ligand experiment, the concentration of initial ligand is decreasing with each scan. Therefore, it is ideal to subtract the buffer scan 1 from sample scan 1, and so on. We have found that the buffer scans with cocaine do not change appreciably as the ligand conversion proceeds and therefore a single thermolabile ligand buffer scan can be used to subtract all of the thermolabile ligand-bound data.</li>
	<li>Convert the baseline-subtracted sample power data to heat capacity. 
	NOTE: The conversion requires the biomolecule&#39;s partial specific volume, which can be estimated14,15,16. The equation for converting power to heat capacity has been described previously17.</li>
</ol>
5. Data Analysis
<ol>
	<li>Globally fit the short equilibration time thermolabile ligand-bound heat capacity dataset with a single set of baseline, ligand concentration, folding, and ligand binding parameters as described previously4.</li>
	<li>Repeat the global fit for the long equilibration time dataset in order to calculate the rate constant for thermolabile ligand conversion as described previously4.</li>
</ol>

<ol><li>Bruylants, G., Wouters, J., Michaux, C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Differential+scanning+calorimetry+in+life+science%3A+thermodynamics%2C+stability%2C+molecular+recognition+and+application+in+drug+design%5BTitle%5D)+AND+%22Curr+Med+Chem%22%5BJournal%5D)">Differential scanning calorimetry in life science: thermodynamics, stability, molecular recognition and application in drug design.</a> Curr Med Chem. 12 (17), 2011-2020 (2005).</li>
<li>Privalov, P. L., Dragan, A. I. <a target="_blank" href="https://www.researchgate.net/profile/Anatoliy_Dragan/publication/7002826_Microcalorimetry_of_biological_macromolecules/links/0912f507f62e09cd1b000000.pdf">Microcalorimetry of biological macromolecules.</a> Biophys Chem. 126 (1-3), 16-24 (2007).</li>
<li>Brandts, J. F., Lin, L. N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Study+of+strong+to+ultratight+protein+interactions+using+differential+scanning+calorimetry%5BTitle%5D)+AND+%22Biochemistry%22%5BJournal%5D)">Study of strong to ultratight protein interactions using differential scanning calorimetry.</a> Biochemistry. 29 (29), 6927-6940 (1990).</li>
<li>Harkness, R. W., Slavkovic, S., Johnson, P. E., Mittermaier, A. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Rapid+characterization+of+folding+and+binding+interactions+with+thermolabile+ligands+by+DSC%5BTitle%5D)+AND+%22Chem+Commun%22%5BJournal%5D)">Rapid characterization of folding and binding interactions with thermolabile ligands by DSC.</a> Chem Commun. 52 (92), 13471-13474 (2016).</li>
<li>Garbett, N. C., Chaires, J. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Thermodynamic+studies+for+drug+design+and+screening%5BTitle%5D)+AND+%22Expert+Opin+Drug+Dis%22%5BJournal%5D)">Thermodynamic studies for drug design and screening.</a> Expert Opin Drug Dis. 7 (4), 299-314 (2012).</li>
<li>Holdgate, G. A., Ward, W. H. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Measurements+of+binding+thermodynamics+in+drug+discovery%5BTitle%5D)+AND+%22Drug+Discov+Today%22%5BJournal%5D)">Measurements of binding thermodynamics in drug discovery.</a> Drug Discov Today. 10 (22), 1543-1550 (2005).</li>
<li>Plotnikov, V., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((An+autosampling+differential+scanning+calorimeter+instrument+for+studying+molecular+interactions%5BTitle%5D)+AND+%22Assay+Drug+Dev+Technol%22%5BJournal%5D)">An autosampling differential scanning calorimeter instrument for studying molecular interactions.</a> Assay Drug Dev Technol. 1 (1), 83-90 (2002).</li>
<li>Schon, A., Lam, S. Y., Freire, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Thermodynamics-based+drug+design%3A+strategies+for+inhibiting+protein-protein+interactions%5BTitle%5D)+AND+%22Future+Med+Chem%22%5BJournal%5D)">Thermodynamics-based drug design: strategies for inhibiting protein-protein interactions.</a> Future Med Chem. 3 (9), 1129-1137 (2011).</li>
<li>Periánez Parraga, L., G-L, A., Gamón Runnenberg, I., Seco Melantuche, R., Delgado Sánchez, O., Puigventós Latorre, F. <a target="_blank" href="http://www.sciencedirect.com/science/article/pii/S2173508511000141">Thermolabile Drugs. Operating Procedure In the Event of Cold Chain Failure.</a> Farmacia Hospitalaria. 35 (4), 1-28 (2011).</li>
<li>Murray, J. B., Alshora, H. I. <a target="_blank" href="http://onlinelibrary.wiley.com/doi/10.1111/j.1365-2710.1978.tb00096.x/full">Stability of Cocaine in Aqueous-Solution.</a> J Clin Pharmacy. 3 (1), 1-6 (1978).</li>
<li>Waterman, K. C., et al. <a target="_blank" href="https://www.ncbi.nlm.nih.gov/pubmed/12066569">Hydrolysis in pharmaceutical formulations.</a> Pharm. Dev. Technol. 7 (2), 113-146 (2002).</li>
<li>Mergny, J. L., Lacroix, L. <a target="_blank" href="https://www.ncbi.nlm.nih.gov/pubmed/15025917">Analysis of thermal melting curves.</a> Oligonucleotides. 13 (6), 515-537 (2003).</li>
<li>Neves, M. A., Reinstein, O., Johnson, P. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Defining+a+stem+length-dependent+binding+mechanism+for+the+cocaine-binding+aptamer.+A+combined+NMR+and+calorimetry+study%5BTitle%5D)+AND+%22Biochemistry%22%5BJournal%5D)">Defining a stem length-dependent binding mechanism for the cocaine-binding aptamer. A combined NMR and calorimetry study.</a> Biochemistry. 49 (39), 8478-8487 (2010).</li>
<li>Bonifacio, G. F., Brown, T., Conn, G. L., Lane, A. N. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Comparison+of+the+electrophoretic+and+hydrodynamic+properties+of+DNA+and+RNA+oligonucleotide+duplexes%5BTitle%5D)+AND+%22Biophys+J%22%5BJournal%5D)">Comparison of the electrophoretic and hydrodynamic properties of DNA and RNA oligonucleotide duplexes.</a> Biophys J. 73 (3), 1532-1538 (1997).</li>
<li>Hinz, H. -J. Chapter 3. <a target="_blank" href="http://scholar.google.com/scholar?hl=en&safe=off&q=author%3aDurchschlag%2C+H+%22Thermodynamic+Data+for+Biochemistry+and+Biotechnology%22">Thermodynamic Data for Biochemistry and Biotechnology</a>. , Springer. Berlin Heidelberg. 45-128 (1986).</li>
<li>Hellman, L. M., Rodgers, D. W., Fried, M. G. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Phenomenological+partial-specific+volumes+for+G-quadruplex+DNAs%5BTitle%5D)+AND+%22Eur+Biophys+J+Biophy%22%5BJournal%5D)">Phenomenological partial-specific volumes for G-quadruplex DNAs.</a> Eur Biophys J Biophy. 39 (3), 389-396 (2010).</li>
<li>Farber, P., Darmawan, H., Sprules, T., Mittermaier, A. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Analyzing+Protein+Folding+Cooperativity+by+Differential+Scanning+Calorimetry+and+NMR+Spectroscopy%5BTitle%5D)+AND+%22J+Am+Chem+Soc%22%5BJournal%5D)">Analyzing Protein Folding Cooperativity by Differential Scanning Calorimetry and NMR Spectroscopy.</a> J Am Chem Soc. 132 (17), 6214-6222 (2010).</li>
<li>Reinstein, O., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Quinine+binding+by+the+cocaine-binding+aptamer.+Thermodynamic+and+hydrodynamic+analysis+of+high-affinity+binding+of+an+off-target+ligand%5BTitle%5D)+AND+%22Biochemistry%22%5BJournal%5D)">Quinine binding by the cocaine-binding aptamer. Thermodynamic and hydrodynamic analysis of high-affinity binding of an off-target ligand.</a> Biochemistry. 52 (48), 8652-8662 (2013).</li>
<li>Tellinghuisen, J. <a target="_blank" href="https://web.stanford.edu/~kimth/www-mit/8.13/error_propagation.pdf">Statistical error propagation.</a> J Phys Chem. A. 105 (15), 3917-3921 (2001).</li>
<li>Drobnak, I., Vesnaver, G., Lah, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/pubmed?term=((Model-based+thermodynamic+analysis+of+reversible+unfolding+processes%5BTitle%5D)+AND+%22J+Phys+Chem+B%22%5BJournal%5D)">Model-based thermodynamic analysis of reversible unfolding processes.</a> J Phys Chem B. 114 (26), 8713-8722 (2010).</li>
</ol>

The authors declare no conflicts of interest.

Modifications and troubleshooting
The details of the global fitting analysis used in Figure 1 and Figure 2 have been described previously4. Here, we outline practical aspects of performing and analyzing DSC binding experiments with thermolabile ligands. Note that a DSC baseline obtained for the thermolabile ligand alone is subtracted from the ligand + biomolecule dataset, effectively cancelling ou...

Differential scanning calorimetry (DSC) is a powerful method for quantitating biomolecular binding and folding interactions1,2,3. The strengths of DSC include its ability to elucidate binding and folding mechanisms, and to yield the corresponding thermodynamic parameters2,3. Furthermore, DSC can be performed in solution under near-physiological conditions and does not require labeling of the biomolecule or ligand, e.g., with fluorophores, spin-labels or nuclear isotopes4. The instrument scans in temperature, measuring the amount of heat required to denature the biomolecule in the presence and absence of ligand. The resulting thermograms are used to extract the thermodynamic parameters governing the ligand binding and folding processes. The information provided by DSC or other thermodynamic techniques is critical to guiding the design of drugs targeting biomolecules1,5,6,7,8. However, the repeated scanning to high temperatures (~ 60 - 100 &#176;C) can be problematic. For example, many pharmaceutically important compounds undergo rearrangement or decomposition upon sustained exposure to high temperatures9,10,11, i.e., they are thermolabile. Examination of binding interactions by DSC typically requires multiple forward and reverse scans in order to verify the reproducibility of the thermogram for thermodynamic analyses12. Thermal conversion of an initial ligand to a secondary form with altered binding characteristics leads to pronounced differences in the shape and position of successive thermograms, since the concentration of the initial ligand decreases with each scan while the thermal conversion products accumulate. These datasets are not amenable to traditional analyses.
We have recently developed a global fitting method for thermolabile ligand DSC datasets that yields the complete set of thermodynamic parameters governing the biomolecular folding and binding interactions from a single ligand-bound experiment referenced to the requisite thermogram for the free biomolecule4. The analysis reduces the experimental time and sample required by ~ 10-fold compared to standard DSC approaches. We have accounted for ligand thermal conversion by assuming this happens during the high temperature portion of each scan where the thermogram does not depend on ligand concentration. Therefore, the ligand concentration is a constant within the portion of the thermogram that is used to extract thermodynamic parameters. We additionally demonstrated how the rate constant for ligand thermal conversion can be obtained by performing one supplementary experiment with a longer high temperature equilibration period. For systems where ligand thermal conversion is less temperature-dependent (i.e., occurring appreciably at all temperatures), the analysis can be modified to include variable ligand concentrations. Here we demonstrate this procedure for the DNA aptamer MN4 in the presence of the thermolabile ligand cocaine, which rapidly converts to benzoylecgonine at high temperatures (&#62;60 &#176;C). Quinine is used as a negative control for ligand thermolability since it does not undergo conversion at these experimental temperatures and also binds to MN4. We describe the acquisition of thermolabile ligand DSC datasets and their analysis yielding thermodynamic and kinetic parameters of the folding, binding, and ligand conversion processes.

<table><tbody><tr><td>Sodium chloride</td><td>Chem Impex</td><td>#00829</td><td></td></tr><tr><td>Sodium phosphate monobasic dihydrate</td><td>Sigma Aldrich</td><td>71502</td><td></td></tr><tr><td>Sodium phosphate dibasic</td><td>Sigma Aldrich</td><td>S9763</td><td></td></tr><tr><td>Deioinized water for molecular biology</td><td>Millipore</td><td>H20MB1001</td><td></td></tr><tr><td>0.2 micron sterile syringe filters</td><td>VWR</td><td>CA28145-477</td><td></td></tr><tr><td>3 kDa centrifugal filters</td><td>Millipore</td><td>UFC900324</td><td></td></tr><tr><td>Dialysis tubing 0.5-1.0 kDa cutoff</td><td>Spectrum Laboratories</td><td>131048</td><td></td></tr><tr><td>Silicon tubing</td><td>VWR</td><td>89068-474</td><td></td></tr><tr><td>Plastic DSC flange caps</td><td>TA Instruments</td><td>6111</td><td></td></tr><tr><td>DNA aptamer MN4</td><td>Integrated DNA Technologies</td><td>https://www.idtdna.com/site/order/menu</td><td></td></tr><tr><td>Cocaine</td><td>Sigma Aldrich</td><td>C008</td><td></td></tr><tr><td>Quinine</td><td>Sigma Aldrich</td><td>22620</td><td></td></tr><tr><td>NanoDSC-III microcalorimeter</td><td>TA Instruments</td><td>http://www.tainstruments.com/nanodsc/</td><td></td></tr><tr><td>DSCRun software</td><td>TA Instruments</td><td>http://www.tainstruments.com/support/software-downloads-support/instruments-by-software/</td><td></td></tr><tr><td>NanoAnalyze software</td><td>TA Instruments</td><td>http://www.tainstruments.com/support/software-downloads-support/instruments-by-software/</td><td></td></tr><tr><td>Contrad-70</td><td>VWR</td><td>89233-152</td><td></td></tr></tbody></table>

measuring biomolecular dsc profiles with thermolabile ligands to rapidly characterize folding and binding interactions

Measuring Biomolecular DSC Profiles with Thermolabile Ligands to Rapidly Characterize Folding and Binding Interactions

Differential scanning calorimetry (DSC) is a powerful technique for quantifying thermodynamic parameters governing biomolecular folding and binding interactions. This information is critical in the design of new pharmaceutical compounds. However, many pharmaceutically relevant ligands are chemically unstable at the high temperatures used in DSC analyses. Thus, measuring binding interactions is challenging because the concentrations of ligands and thermally-converted products are constantly changing within the calorimeter cell. Here, we present a protocol using thermolabile ligands and DSC for rapidly obtaining thermodynamic and kinetic information on the folding, binding, and ligand conversion processes. We have applied our method to the DNA aptamer MN4 that binds to the thermolabile ligand cocaine. Using a new global fitting analysis that accounts for thermolabile ligand conversion, the complete set of folding and binding parameters are obtained from a pair of DSC experiments. In addition, we show that the rate constant for thermolabile ligand conversion may be obtained with only one supplementary DSC dataset. The guidelines for identifying and analyzing data from several more complicated scenarios are presented, including irreversible aggregation of the biomolecule, slow folding, slow binding, and rapid depletion of the thermolabile ligand.

Representative data for the thermolabile ligand DSC are shown in Figure 1. The position and height of the thermolabile ligand-bound peak successively shifts down towards that of the unbound biomolecule as the thermolabile ligand is depleted with each scan (Figure 1a). The free denaturation profile is used as a reference for the endpoint of thermolabile ligand conversion (Figure 1b). Data for MN4 boun...

We present a protocol for rapid characterization of biomolecular folding and binding interactions with thermolabile ligands using differential scanning calorimetry.

Differential scanning calorimetry (DSC) is a powerful technique for quantifying thermodynamic parameters governing biomolecular folding and binding ...

The overall goal of this methodology is to extract the thermodynamic parameters governing biomolecular folding and binding interactions by differential scanning calorimetry, or DSC, using a thermolabile ligand in as little as two experiments. This method can help answer key questions in the biocalorimetry and drug design fields such as what are the relative magnitudes of the thermodynamic parameters governing interactions between biomolecules and tight binding inhibitors? The main advantage of this technique is that a full ligand titration is performed in a single experiment permitting rapid extraction of thermodynamic parameters from the global fitting analysis.To begin, prepare buffers for dialysis of the purified biomolecule into solution of ligands. Dialyze the biomolecule against at least one liter of buffer using dialysis tubing with 0.5 to 1.7 kilodalton cutoff. The most important step in obtaining high-quality DSC data is the dialysis of the biomolecule ligand against the desired buffer.This ensures that there are no buffer mismatched artifacts present in the DSC data. Filter the final buffer which is referred to as the working buffer through a 0.2-micron filter that has been thoroughly equilibrated with buffer. Weigh out the desired masses of the ligands and dissolve them in filtered working buffer.If the desired ligand concentrations require masses that are too small to accurately weigh, make a concentrated ligand stock solution. Filter the biomolecule stock solution through a 0.2-micron filter that has been thoroughly equilibrated with working buffer. Then, determine the biomolecule concentration by absorbance measurements.Store the prepared biomolecule and ligand in a four degrees Celsius refrigerator or at minus 20 or minus 80 degrees Celsius if the biomolecule and ligands tolerate freezing and long-term storage is required. Degas the buffer by a molecule and ligand solutions in a tabletop degasser prior to loading into the differential scanning calorimeter, or DSC. Unscrew the pressure handle from the DSC.Then, run silicon tubing from the working buffer and attach it to the front flange of the reference capillary. Create a bridge between the reference and sample capillaries by connecting the rear reference flange to the front simple flange. Next, attach a piece of silicon tubing to the rear sample flange that runs to a waste flask with a vacuum line attached.Turn on the vacuum line to flush the DSC with 200 milliliters of working buffer. Begin by attaching roughly three to five-centimeter sections of silicon tubing to the reference capillary flanges. Next, insert a one-milliliter pipette tip into the silicon tubing of the rear flange.Draw 0.8 milliliters of working buffer with a pipette and insert the pipette tip with buffer into the silicon tubing of the front reference flange. Gently press the pipette plunger down to pass the working buffer through the front silicon tubing into the reference capillary and up into the attached pipette tip of the rear flange. Press the pipette plunger down until the working buffer level reaches just above the front silicon tubing, then release the pipette plunger until the working buffer level reaches just above the rear silicon tubing.Continue passing the working buffer back and forth in the reference capillary to purge the volume of bubbles. Next, cap the rear pipette tip with a forefinger and gently pull up on the rear pipette tip and front pipette to remove them from the reference flanges with the silicon tubing attached. Load the sample capillary with working buffer as before.Place a black plastic cap on the rear reference sample flanges leaving the front flanges uncovered. Attach the pressure handle to the DSC and then open the DSC software and pressurize the instrument by clicking the red up arrow at the top of the interface once the power reading has stabilized. The DSC power is indicated in a box at the top right of the interface along with the instrument temperature and pressure reading.Equilibrate the DSC with working buffer by performing a forward and reverse scan in the experimental method tab on the left side of the screen. Ensure that the scanning option is selected to run the DSC and temperature scanning mode. In the temperature parameters inset under the experimental method tab, click the button for heating.Enter one and 100 degrees Celsius for the lower and upper experimental temperatures, one degree Celsius per minute for the scan rate and 60 seconds for the equilibration period. Click the AddSeries button under the input field for the equilibration period. Enter two into the steps to add field in the popup window and check the Alternate Heating/Cooling box.Click OK.The added scans appear in the lower portion of the interface. Check that the parameters for each scan are as desired. Start the experiment by clicking the green play button at the top of the interface.Navigate to the desired window and input a file name for saving the experiment in the popup window. View the experiment progress by clicking the data tab to the right of the experiment method tab. Run reference experiments for a baseline subtraction of the sample data by reloading the DSC with working buffer in both capillaries.Collect multiple forward and reverse scans over a suitable temperature range at one degree Celsius per minute with an up equilibration time of 120 seconds. Delete the previous buffer equilibration scans from the lower portion of the interface by highlighting each individually and clicking the red X to the middle right of the interface. Add the new scans by clicking the AddSeries button entering 20 in the field for steps to add and checking the Alternate Heating/Cooling box.Then, click OK and run the experiment by clicking the green play button as before. Repeat these steps with working buffer containing the desired concentration of ligand in both capillaries to obtain the reference experiments for the ligand. Collect two separate experiments to be used in acquiring the rate constant for thermolabile conversion.For the free biomolecule data set, ensure that the reference capillary contains the working buffer while the sample capillary contains the free biomolecule at the desired concentration in working buffer. Next, run the sample experiments using the same DSC loading procedure and experimental parameters used in the reference scans. For the ligand-bound experiments, ensure that the ligand is in the working buffer and the reference capillary and the biomolecule plus ligand are in the working buffer in the sample capillary.Flush the system between additions of different ligands as before. Perform one additional experiment with the biomolecule bound to the thermolabile ligand where the high-temperature equilibration period is increased to 600 seconds and all other experimental parameters are the same as before. Proceed to the data processing and analysis as described in the text protocol.The position and height of the thermolabile ligand bound peak successively shifts down towards that of the unbound molecule as the thermolabile ligand is depleted with each scan. The 3D maturation profile is used as a reference for the endpoint of thermolabile ligand conversion. Increasing the high-temperature equilibration period yields more pronounced reductions of the thermolabile ligand concentration with each scan relative to the short equilibration period dataset.Using the optimized global fit concentration parameters from the two datasets, the rate constant for ligand conversion at the high equilibration temperature can be calculated. Once mastered, this technique can be done in 72 hours if performed properly. When attempting this procedure, it is important to remember to degas the biomolecule ligand as well to purge the DSC capillaries of bubbles using the loading pipette to prevent data artifacts.After watching this video and reading the article, you should have a good understanding of how to perform DSC experiments on biomolecules as well as the implementation of global fitting analyses in order to rapidly extract thermodynamic parameters governing folding and binding interactions. Though this method can provide insight into equilibrium folding binding interactions, it can also be applied to other systems such as biomolecules that exhibit slow-folding and/or ligand-binding kinetics.

measuring-biomolecular-dsc-profiles-with-thermolabile-ligands-to

Research

JoVE Journal

Biochemistry

A general protocol for the use of isothermal titration calorimetry to monitor the binding thermodynamics for biological systems with moderate binding affinities is presented.

Isothermal Titration Calorimetry for Measuring Macromolecule-Ligand Affinity

This video demonstrates differential scanning calorimetry — a technique to study the interaction between a biomolecule and a ligand. The binding of a DNA aptamer and a thermolabile ligand is studied by applying repeated heating and cooling cycles to the sample and obtaining scans for thermodynamic analysis.

Differential Scanning Calorimetry to Study DNA Aptamer-Thermolabile Ligand Interaction

Microscale thermophoresis (MST) can be widely used for determination of binding affinity without purification of the target protein from cell lysates. The protocol involves overexpression of the GFP-fused protein, cell lysis in non-denaturing conditions, and detection of MST signal in the presence of varying concentrations of the ligand.

Protein Purification-free Method of Binding Affinity Determination by Microscale Thermophoresis

Differential scanning fluorimetry is a widely used method for screening libraries of small molecules for interactions with proteins. Here, we present a straightforward method to extend these analyses to provide an estimate of the dissociation constant between a small molecule and its protein partner.

Determination of Protein-ligand Interactions Using Differential Scanning Fluorimetry

Differential scanning calorimetry measures the thermal transition temperature(s) and total heat energy required to denature a protein. Results obtained are used to assess the thermal stability of protein antigens in vaccine formulations.

Differential Scanning Calorimetry &#8212; A Method for Assessing the Thermal Stability and Conformation of Protein Antigen

Here, we present a protocol for the production and purification of proteins that are labeled with stable isotopes, and subsequent characterization of protein-protein interactions using Nuclear Magnetic Resonance (NMR) spectroscopy and MicroScale Thermophoresis (MST) experiments.

Measuring Interactions of Globular and Filamentous Proteins by Nuclear Magnetic Resonance Spectroscopy (NMR) and Microscale Thermophoresis (MST)

Microscale thermophoresis obtains binding constants quickly at low material cost. Either labeled or label free microscale thermophoresis is commercially available; however, label free thermophoresis is not capable of the diversity of interaction measurements that can be performed using fluorescent labels. We provide a protocol for labeled thermophoresis measurements.

Use of Microscale Thermophoresis to Measure Protein-Lipid Interactions

Monitoring changes in the melting temperature of a target protein (i.e., thermal shift assay, TSA) is an efficient method for screening fragment libraries of a few hundred compounds. We present a TSA protocol implementing robotics-assisted nano-Differential Scanning Fluorimetry (nano-DSF) for monitoring intrinsic tryptophan fluorescence and light back-scattering for fragment screening.

Nano-Differential Scanning Fluorimetry for Screening in Fragment-based Lead Discovery

This protocol describes a unique method for detecting the binding between compounds and protein molecules, offering the advantages of minimal protein sample loss and high data accuracy.

Detection of CD40 Protein-Umbelliferone Interaction via Differential Scanning Fluorescence

Here, we present the thermal shift assay, a high-throughput, fluorescence-based technique used to investigate the binding of small molecules to proteins of interest.

Utilizing Thermal Shift Assay to Probe Substrate Binding to Selenoprotein O

Learn differential scanning calorimetry for biomolecular folding and binding interactions using thermolabile ligands. This protocol enables rapid extraction of thermodynamic parameters with minimal experiments.

Measuring Biomolecular DSC Profiles with Thermolabile Ligands to Rapidly Characterize Folding and Binding Interactions

Explore More Videos