Generation of Recombinant Viral Particles Using Embryonic Kidney Cells

In diesem Artikel

Zusammenfassung

Source: Vijayraghavan, S., Kantor, B. A Protocol for the Production of Integrase-deficient Lentiviral Vectors for CRISPR/Cas9-mediated Gene Knockout in Dividing Cells. J. Vis. Exp. (2017).

This video demonstrates the procedure for generating recombinant viral particles by transfecting embryonic kidney cells with plasmids encoding viral proteins and a gene of interest.

Protokoll

Transfecting Human Embryonic Kidney cells (HEK-293T) Using a Calcium Phosphate-based Protocol
1. Transfection reagents
  1. To prepare 2x BES-buffered solution BBS (50 mM BES, 280 mM NaCl, 1.5 mM Na₂HPO₄), combine 16.36 g of NaCl, 10.65 g of BES (N, N-bis (2-hydroxyethyl)-2-amino-ethanesulfonic acid), and 0.21 g of Na₂HPO₄. Add double-distilled H₂O (dd-H₂O) up to 900 mL. Dissolve, titrate to pH 6.95 with 1M NaOH, and bring volume to 1 L. Filter via a 0.22 µM filter unit. Store at -20 °C.
  2. Prepare 1M CaCl₂. Filter solution via a 0.22 µM filter. Store at 4 °C.
Observe the plates that were seeded a day prior. Cells are ready for transfection once they reach 70 - 80% confluency.
Aspirate old media from the plates and gently add freshly-prepared media without serum.
Prepare the plasmid mix by aliquoting the four plasmids into a 15-mL conical tube. For a single 15-cm dish preparation, use 37.5 µg of the CRISPR/Cas9-transfer vector (pBK198 or pBK189), 25 µg of pBK43 (psPAX2-D64E), 12.5 µg pMD2.G, and 6.25 µg of pREV (Figure 1c).
Add 312.5 µL 1M CaCl₂ to the plasmid mix. To this, add up to 1.25 mL of sterile dd-H₂O.
Slowly (drop-wise) add 1.25 mL of 2x BBS solution while vortexing the mix. Incubate for 30 min at room temperature.
Add the transfection mixture dropwise to each 15-cm plate (2.5 mL per plate). Swirl the plates gently and incubate at 37 °C with 5% CO₂ for 2 - 3 h. Thereafter, add 2.5 mL (10%) serum per plate and continue incubating overnight (12 - 18 h).
NOTE: Some labs use 3% CO₂ incubators to stabilize media pH. However, we do not observe any difference in transfection efficiency between 3% and 5% CO₂. Also, the size of CaPO₄ precipitates is crucial for transfection efficiency; the transfection mix has to be clear prior to its addition onto the cells. If the mix becomes cloudy during incubation, prepare fresh 2x BBS (pH = 6.95).

2. Day After Transfection

Observe the cells to ensure that they are nearing 100% confluency at this point with little to no cell death. Replace media by adding 25 mL of fresh DMEM + 10% serum to each plate. Continue incubating at 37 °C with 5% CO₂ for an additional 48 h.

Zugriff eingeschränkt. Bitte melden Sie sich an oder starten Sie eine Testversion, um diesen Inhalt anzuzeigen.

Ergebnisse

Figure 1: IDLV packaging. (a) Schematic of the wild-type integrase protein (b) The modified plasmid was derived from psPAX2. Representative agarose gel image of clones screened for mutated integrase clones...