5.8
If the quality of water available for preparing concrete is uncertain, its suitability is determined by comparing the setting time of cement and the compressive strength of mortar cubes made with the test water against those made with de-ionized or distilled water.
If the values obtained for setting time and compressive strength are within the permissible limits mentioned in the standards, the test water can be used to prepare concrete.
If brackish water is the only available option for mixing concrete, verifying that the concentration of chlorides, sulfates, and alkalis present in it are within the allowable limits prescribed in the standards is crucial in preserving concrete quality.
In case seawater is used for mixing concrete, the compressive strength of the concrete prepared with seawater and freshwater is tested, and the results are compared to ensure that the long-term stability is not reduced by more than 15 percent.
The possibility of water used for curing to cause staining on concrete surfaces can be determined by conducting performance tests that simulate wetting and evaporation on concrete surfaces.
כאשר איכות המים להכנת בטון אינה ודאית, בודקים את השפעתם על זמן ההתייצבות של המלט וחוזק הלחיצה של הטיט באמצעות השוואה לערכים שנקבעו עם מים מיוננים או מזוקקים. תקן ASTM C1602 האמריקאי דורש שזמני ההתייצבות יהיו בטווח של 90 דקות ביחס לדגימה הבקרה, תקן בריטי BS 3146:1980 מתיר סטייה של 30 דקות בזמן ההתייצבות ההתחלתי, בעוד התקן האירופאי BS EN 1008 קובע שזמן ההתייצבות ההתחלתי לא יהיה פחות משעה וזמן ההתייצבות הסופי לא יעלה על 12 שעות, עם סטייה של עד 25 אחוזים מהתוצאות שהושגו עם מים מזוקקים. קוביות טיט שהוכנו עם המים הנבדקים חייבות להגיע לפחות ל-90 אחוזים מחוזק הלחיצה של קוביות טיט שהוכנו עם מים מזוקקים.
בדיקות לזיהומים, כגון כלורידים, סולפטים, מוצקים כלליים, בסיסיות וכדומה, הן קריטיות, שכן הריכוזים שלהם חייבים להיות בטווחי הגבולות שנקבעו כדי להבטיח את איכות הבטון. כאשר נעשה שימוש במי ים, חוזק הלחיצה לטווח הארוך של הבטון חייב להיות נמוך לכל היותר ב־15 אחוזים לעומת בטון שהוכן עם מים מתוקים. בנוסף, מבוצעים מבחני ביצועים המדמים הרטבה וייבוש טבעיים כדי לבדוק אפשרות להכתמה, מהלך הכרחי כדי לוודא את התאמת המים לאשפרת הבטון מבלי לפגוע במראהו החיצוני.
If the quality of water available for preparing concrete is uncertain, its suitability is determined by comparing the setting time of cement and the compressive strength of mortar cubes made with the test water against those made with de-ionized or distilled water.
If the values obtained for setting time and compressive strength are within the permissible limits mentioned in the standards, the test water can be used to prepare concrete.
If brackish water is the only available option for mixing concrete, verifying that the concentration of chlorides, sulfates, and alkalis present in it are within the allowable limits prescribed in the standards is crucial in preserving concrete quality.
In case seawater is used for mixing concrete, the compressive strength of the concrete prepared with seawater and freshwater is tested, and the results are compared to ensure that the long-term stability is not reduced by more than 15 percent.
The possibility of water used for curing to cause staining on concrete surfaces can be determined by conducting performance tests that simulate wetting and evaporation on concrete surfaces.
From Chapter 5:
Now Playing
Aggregates and Water
683 Views
Aggregates and Water
589 Views
Aggregates and Water
918 Views
Aggregates and Water
2.7K Views
Aggregates and Water
2.2K Views
Aggregates and Water
2.0K Views
Aggregates and Water
1.9K Views
Aggregates and Water
804 Views
Aggregates and Water
1.1K Views
Aggregates and Water
1.9K Views
Aggregates and Water
1.8K Views
Aggregates and Water
1.1K Views
Aggregates and Water
1.2K Views
Aggregates and Water
1.8K Views
Aggregates and Water
1.1K Views
See More