Improving the Application of High Molecular Weight Biotinylated Dextran Amine for Thalamocortical Projection Tracing in the Rat

The overall goal of this video is to demonstrate a refined protocol for the application of high molecular weight BDA for studying the optimal neural labeling in the central nervous system. This measure can help answer key questions in the neural networking field. By visualizing the frame structure of neural labeling through neural circuits.

The main advantage of this technique is that it provides the opportunity to start a local neural circuits and their chemical characteristics. Prepare one microliter microsyringe, equipped with a glass micropipet, and test it by drawing up liquid paraffin. After anesthetizing the rat using an approved protocol, confirm deep anesthesia by the absence of reaction to a tail pinch.

Then shave the top of the animal's head with an electric razor and scrub the surgical site with 10%povidone iodine, followed by 70%ethanol. Secure the rat into the stereotaxic device by inserting blunt ear bars into the ears and placing the rat's upper incisors into the mouth holder. Apply an ophthalmic ointment on the eyes.

Use sterile surgical gloves and drapes to maintain sterile conditions. Clean the head skin of the surgical site again using 70%ethanol. After making a sagittal incision in the skin with a scalpel, along the sagittal suture, use sterile cotton-tipped applicators to scrape the muscle and periosteum away from the skull.

Using pre-defined coordinates from an atlas, determine the location for the craniotomy. Perform a craniotomy using a burr drill with a round tip bit to drill to about a one millimeter depth until the meninges are visible. Excise the dura mater using micro forceps to expose the cerebral cortex over the injection site.

Expel the liquid paraffin from the microsyringe and then draw up 10%BDA solution. Mount the syringe into the microinjection apparatus and connect the micropump. Under a stereomicroscope, manipulate the microinjection apparatus.

Insert the filled glass micropipet into the VPM through the cortical surface of the brain, to a depth of 5.8 millimeters. Then, use the micropump to pressure-inject 100 nanoliters of 10%BDA into the VPM, over a period of three minutes. After five minutes, slowly withdraw the pipet.

Suture the wound with sterile thread, then place the rat in a warm recovery area, until it regains consciousness and is fully recovered. After euthanizing the rat, use scissors and forceps to open the thoracic cavity of the rat and access the heart. Insert an intravenous catheter into the left ventricle, toward the aorta, and then open the right auricle.

First, perfuse with 0.9%saline at physiological temperature, for about one to two minutes, until the blood exiting from the heart is clear. And then continue with 250 to 300 milliliters of 4%paraformaldehyde, in 0.1 molar phosphate buffer. Post-fix the dissected brain in 4%paraformaldehyde for two hours at room temperature.

Then transfer the brain to 30%sucrose in 0.1 molar PBS and cryoprotect for three days at four degrees Celsius. After three days, when the brain has sunk in the solution, divide the brain into three blocks in the coronal direction with the aid of a brain matrix. The central block contains the ventral posteromedial nucleus of thalamus in the primary somatosensory cortex.

Mount the central block of the brain on the freezing stage of the sliding microtome for sectioning in the coronal plane and section at 40 microns when frozen. Collect the sections in a six-well dish, containing 0.1 molar PBS. Begin staining by rinsing the sections in 0.1 molar PBS for about one minute with rocking.

Then transfer the sections to a mixed solution of streptavidin-AF594 in AF500/525 green fluorescent Nissl stain in 0.1 molar PBS containing 0.3%Triton X-100, and incubate for two hours at room temperature. After staining, wash the sections three times in 0.1 molar PB with rocking. Mount the sections on the microscope slides using standard histochemical techniques.

Air dry the sections for about an hour. Apply 50%glycerin in distilled water to the thorescent sections and cover slip before imaging the slides. This representative photomicrograph shows the injection site of BDA in red of the ventral posteromedial nucleus of thalamus on the background of green Nissl staining.

Thorescent BDA-labeling is shown here, including thalamyl corticol axons in layer four and cortical thalamic neurons in layers five and six. For comparison, this photomicrograph demonstrates that conventional BDA-labeling with a standard avidin-biotin peroxidase procedure reveals a similar pattern of neural labeling to thorescent BDA-labeling. This higher magnification view of a thorescent BDA-labeled section shows the anterogradely labeled axonal arbors in detail, in red.

The retrogradely labeled neuronal cell body, dendrites and dendritic spines are shown in detail here. Once mastered, craniotomy and stereotaxic injection can be done in 20 to 30 minutes, if it's performed properly. After watching this video, you should have a good understanding of how to apply high molecular weight BDA to revive neuronal connections and detailed structure of neural labeling.