Pump Probe Spectroscopy
Pump Probe Spectroscopy - Related Videos
10:53
Scanning-probe Single-electron Capacitance Spectroscopy
0 Views •
2013
Scanning-probe single-electron capacitance spectroscopy facilitates the study of single-electron motion in localized subsurface regions. A sensitive charge-detection circuit is incorporated into a cryogenic scanning probe microscope to investigate small systems of dopant atoms beneath the surface of semiconductor samples.
09:21
Mössbauer Spectroscopy
0 Views •
2023
Source: Joshua Wofford, Tamara M. Powers, Department of Chemistry, Texas A&M University Mössbauer spectroscopy is a bulk characterization technique that examines the nuclear excitation of an atom by gamma rays in the solid state. The resulting Mössbauer spectrum provides information about the oxidation state, spin state, and electronic environment around the target atom, which, in combination, gives evidence about the electronic structure and ligand arrangement (geometry) of the molecule.
10:59
Determination of Lipid Raft Partitioning of Fluorescently-tagged Probes in Living Cells by Fluorescence Correlation Spectroscopy (FCS)
0 Views •
Cited by 9 •
2012
A technique to probe the lipid raft partitioning of fluorescent proteins at the plasma membrane of living cells is described. It takes advantage of the disparity in diffusion times of proteins located inside or outside of lipid rafts. Acquisition can be performed dynamically in control conditions or after drug addition.
08:11
Infrared Spectroscopy
0 Views •
2023
Source: Vy M. Dong and Zhiwei Chen, Department of Chemistry, University of California, Irvine, CA This experiment will demonstrate the use of infrared (IR) spectroscopy (also known as vibrational spectroscopy) to elucidate the identity of an unknown compound by identifying the functional group(s) present. IR spectra will be obtained on an IR spectrometer using the attenuated total reflection (ATR) sampling technique with a neat sample of the unknown.
08:10
Molecular Spring Constant Analysis by Biomembrane Force Probe Spectroscopy
0 Views •
Cited by 6 •
2021
A biomembrane force probe (BFP) is an in situ dynamic force spectroscopy (DFS) technique. BFP can be used to measure the spring constant of molecular interactions on living cells. This protocol presents spring constant analysis for molecular bonds detected by BFP.
FAQs
The pump and probe pulses serve different analytical roles. The pump places the material in an excited state, while the delayed probe samples how that state changes without being the excitation itself. Comparing the probe response with the material’s initial optical behavior reveals transient effects associated with carrier relaxation, energy transfer, and recombination. This separation enables time-resolved analysis.
Changing the delay between pulses converts the measurement into a timeline of excitation dynamics. Very short delays can capture early changes, whereas longer delays follow slower behavior, extending from femtoseconds to nanoseconds. The resulting time dependence helps distinguish rapid carrier relaxation from later energy-transfer or recombination processes, linking observed signals to material operation.
Pump Probe Spectroscopy can monitor changes in transmission, reflection, or absorption, and the selected observable determines how the excited material is evaluated optically. A transient change in one of these quantities indicates that excitation has altered the sample’s optical response. Measuring these responses over delay provides complementary evidence about how the excited state evolves.
Controlled excitation is important because the measured response must be related to a known optical disturbance. The pump establishes the starting condition for the transient experiment, and the probe tracks the resulting evolution. In engineering studies, this controlled relationship allows transient behavior to be compared with functional performance in semiconductors, photovoltaic materials, nanostructures, and photonic devices.
A typical measurement begins by directing a controlled pump pulse at the sample, then sending a probe pulse after a chosen delay. The experiment records the probe-related change in transmission, reflection, or absorption as the delay is varied. Researchers then examine the resulting time-dependent response to identify relaxation, transfer, and recombination behavior.
The measured transient response connects excited-state behavior with engineering-relevant performance. The timing and evolution of optical changes can show how carriers relax, how energy moves through a material, or how recombination proceeds. These observations help researchers evaluate whether a semiconductor or photovoltaic material can support the desired optical or optoelectronic function.
In photovoltaic materials, the technique helps relate excited-state dynamics to behavior that supports energy technologies. In photonic devices and nanostructures, it reveals transient optical properties that may affect device speed or operation. Engineers use these links to guide designs for faster optoelectronic components, more efficient energy technologies, and materials with tailored optical properties.