Vacuum Assisted Resin Infusion
Vacuum Assisted Resin Infusion - Related Videos
06:20
Proper Operation of Vacuum Based Equipment
0 Views •
2023
Source: Robert M. Rioux, Ajay Sathe & Zhifeng Chen, Pennsylvania State University, University Park, PA Vacuum is required for a number of laboratory procedures. This is most routinely achieved in the laboratory by the use of vacuum pumps. In addition to working at low pressures, vacuum pumps can also be used to enable rapid changing of the atmospheres in a reactor or flask by evacuation and backfilling.
15:33
Microwave-assisted Functionalization of Poly(ethylene glycol) and On-resin Peptides for Use in Chain Polymerizations and Hydrogel Formation
0 Views •
Cited by 32 •
2013
This video will illustrate a rapid, efficient method to methacrylate poly(ethylene glycol), enabling chain polymerizations and hydrogel synthesis. It will demonstrate how to similarly introduce methacrylamide functionalities into peptides, detail common analytical methods to assess functionalization efficiency, provide suggestions for troubleshooting and advanced modifications, and demonstrate typical hydrogel characterization techniques.
02:44
Endovascular Treatment of Acute Ischemic Stroke Using the Stent Retriever-Assisted Vacuum-Locked Extraction Technique
0 Views •
2025
Source: Schregel, K., et al. Optimized Management of Endovascular Treatment for Acute Ischemic Stroke. J. Vis. Exp. (2018).This video demonstrates the endovascular treatment of acute ischemic stroke using the stent retriever-assisted vacuum-locked extraction technique. A guiding sheath is introduced through the femoral artery to reach the clot. A catheter with a stent retriever secures and extracts the clot. Vascular imaging is done to confirm successful reperfusion.
02:38
Anion Exchange Resin–Based Detection of Viruses from Bioaerosols
0 Views •
2026
Source: Schaeffer, J. W., Chandler, et al. Detection of Viruses from Bioaerosols Using Anion Exchange Resin. J. Vis. Exp. (2018).This video demonstrates the detection of viruses from bioaerosols using an anion exchange resin. A liquid impinger containing the resin is used to capture viruses from the air. The resin is collected and treated with a virus lysis buffer containing carrier RNA. The lysate is transferred to a microcentrifuge tube for viral RNA isolation, followed by qRT-PCR to amplify...
02:16
Microfluidic-Based Microinjectrode System for Combined Drug Infusion and Electrophysiology
0 Views •
2025
Source: Vanegas, M. I., et al. Microinjectrode System for Combined Drug Infusion and Electrophysiology. J. Vis. Exp. (2019)This video demonstrates a microelectrode-based microfluidic device that delivers drug solution through a capillary tube, using an oil-based marker solution for precise volume tracking and enabling simultaneous neural recording and drug infusion.
FAQs
The sealed vacuum bag creates a pressure difference that drives liquid resin through the interconnected pores of the dry fiber preform. Resin flow must remain sufficient to reach the intended regions and wet the fibers before curing begins. If flow is poorly controlled, incomplete impregnation can reduce structural consistency and affect the finished component’s performance.
Fiber placement determines where reinforcement contributes strength, while porosity provides pathways for resin movement through the preform. A well-arranged dry reinforcement helps the resin distribute throughout the intended structure and supports uniform wetting. In bioengineering components, controlling these features helps balance low weight with the strength required for prosthetic or orthotic use.
Curing conditions determine how the resin-impregnated material develops into a rigid composite. The process must allow the resin to solidify after it has adequately wetted the fibers, preserving the intended fiber arrangement and component shape. Consistent curing supports repeatable structures, whereas poorly controlled conditions can undermine manufacturing consistency and the resulting component’s reliability.
A typical workflow places dry fiber reinforcement in the desired arrangement, encloses it within a sealed vacuum bag, introduces liquid resin using the applied vacuum pressure, and allows the impregnated material to cure. The sequence links material preparation, bag sealing, resin movement, and solidification. Each stage affects whether the final composite forms as intended.
Resin flow, fiber placement, and curing conditions are central variables because they govern how completely the reinforcement becomes impregnated and how uniformly the structure solidifies. Monitoring these factors can limit defects associated with uneven wetting or inconsistent formation. Better control also reduces excess material and improves manufacturing efficiency without abandoning the lightweight composite design.
In bioengineering, the method supports fabrication of prosthetic limbs, orthotic devices, and other biomedical components that require high strength with low weight. Its value comes from combining fiber reinforcement with controlled resin processing to create rigid structures while limiting unnecessary material. These characteristics make the approach relevant when component mass and structural performance both matter.