A subscription to JoVE is required to view this content.  Sign in or start your free trial.
Electrical Safety
  • 00:04Overview
  • 01:12Before Powering Up
  • 02:16Avoiding Electrical Shock
  • 02:59In Case of an Emergency
  • 04:29Summary

電気的安全性

English

Share

Overview

ロバート ・ m ・ Rioux ・ Suprita Jharimune、ペンシルバニア州立大学、大学公園、PA

研究室では、現在の多くの危険の間で電気的危険性である操作の最も一般的な我々 は、実験室のほとんどを認識しなければならないの使用する機器が電気を必要とします。不適切な取り扱いや電気機器の操作は傷害また更に死の潜在的なリスクと感電する可能性があります。(以来、多くの可燃性物質は、電化機器近くに保存可能性があります)、電気火花は火災または爆発する可能性があります。したがって、電気安全と緊急対処に関する知識は、研究者のために不可欠です。注意事項は、感電や電気火災や爆発を避けるために研究室で作業するときに使用できます。

Principles

Procedure

1 です。 電気危険に備えて 研究所電気コントロール パネルの場所に精通していると緊急の場合電源をシャット ダウンする方法を知っています。研究室でブレーカーを探し、回路に接続されている電化機器を識別します。すべて遮断する必要があります適切に分類されるが、研究領域や特定の機器を識別する関連付けられている。 タイプと電気火災の場合の消火器の場所に精…

Applications and Summary

Electrical devices are everywhere in the laboratory. It is essential to follow electrical safety principles to prevent electrical shock, electrical fire, or explosion. Be prepared about what steps should be taken in the case of emergency. Identify and mark the location of fire extinguishers in the laboratory. Be sure to use an extinguisher meant for a Class C fire. Always remember to get to personal safety first and then shut down the power to any malfunctioning electrical devices if it can be done in a safe manner.

References

  1. Electrical Safety in the Lab, 2009, Lab Manager. at http://www.labmanager.com/lab-health-and-safety/2009/11/electrical-safety-in-the-lab?fw1pk=2#.V7DGYT4rJcw
  2. Electrical Safety in the Laboratory, Environmental Health & Center, the University of Iowa. at https://ehs.research.uiowa.edu/electrical-safety-laboratory
  3. Portable Fire Extinguishers: Fire Extinguisher Use at https://www.osha.gov/SLTC/etools/evacuation/portable_use.html

Transcript

Safe handling of electrical equipment is as important as the handling of chemical materials, however, the hazardous nature of electrical devices is often overlooked.

Improper operation of electrically-powered devices may potentially lead to injury or death by electric shock. Additionally, electrical sparks in the laboratory may lead to fire or explosions, especially when highly flammable or potentially explosive chemicals are placed in close proximity.

Prevention of electrical accidents involves inspection of electrical wiring, keeping power cords at distances safe from water or chemicals, and situational awareness.

This video will illustrate the necessary precautions to take before using electrically-powered devices, and the procedures used to prevent or handle shock-related accidents and electrical fires.

Before powering up any electrical device, make sure the power cord is in good condition. Do not use the device with a frayed cord or exposed wires.

Make sure the device is on a sturdy surface free from clutter or debris to prevent it from falling. Additionally, keep flammable and corrosive chemicals at a safe distance from electrical outlets.

Familiarize yourself with the emergency electrical shut off and the circuit breaker box in the event that a device needs to be shut down. Properly label the circuits to which each electrical outlet is connected.

Inspect all laboratory electrical equipment on a regular basis by checking for the wiring conditions. In case of damaged wire or defective device have the parts replaced by experienced personnel immediately.

To prevent electrical shock, keep plugged-in devices away from any water-filled sinks or tubs, and avoid touching them with wet hands.

Additionally, use only electrically-powered devices equipped with a grounding plug. Avoid forcing a plug into an ill-fitting socket, and replace any damaged sockets or plugs.

Always use surge protectors to protect electrical devices from voltage spikes, and never use extension cords for permanent laboratory equipment.

Electrical fires may be caused by contact with flammable chemicals, but also by overloaded circuits. Use no more than two electrical devices per outlet, or use surge protectors to prevent overload. Additionally, keep electrical devices away from open flames to avoid melting of the wire.

Always know the location of the fire extinguisher. In case of a small electrical fire, use a CO2 extinguisher or sand.

If a fire extinguisher needs to be used follow the PASS rule. Pull the pin first. Then take the nozzle and aim towards the base of the fire and squeeze the trigger. Slowly sweep the nozzle from side to side to cover the burning area.

In case of a large fire, sound the fire alarm, leave the area immediately, and call 911.

If a lab worker has been electrically shocked, ensure that the power is off, and call 911. Do not touch the victim with bare skin to avoid acting as a conduit for the electricity to reach ground. Always use non-conductive materials such as wood, glass or rubber to help the electrically shocked person.

You’ve just watched JoVE’s introduction to electrical safety. You should now understand safeguards against electrical safety hazards, how to be prepared in the event of an accident, what to do to prevent an electric shock and electrical fires. Thanks for watching!

Tags

Cite This
JoVE Science Education Database. JoVE Science Education. Electrical Safety. JoVE, Cambridge, MA, (2023).