JoVE Journal
Engineering
Single-Digit Nanometer Electron-Beam Lithography with an Aberration-Corrected Scanning Transmission Electron Microscope
1Center for Functional Nanomaterials, Brookhaven National Laboratory
Engineering
One-Step Approach to Fabricating Polydimethylsiloxane Microfluidic Channels of Different Geometric Sections by Sequential Wet Etching Processes
1Research Center for Applied Sciences, Academia Sinica, 2Department of Civil Engineering, Tamkang University, 3College of Engineering, Chang Gung University
Engineering
Multiscale Structures Aggregated by Imprinted Nanofibers for Functional Surfaces
1Department of Mechanical Engineering, Changwon National University, 2Department of Mechanical Engineering, Massachusetts Institute of Technology, 3Printed Electronics Research Team, Korea Institute of Machinery and Materials
Engineering
Determining Tribocorrosion Rate and Wear-Corrosion Synergy of Bulk and Thin Film Aluminum Alloys
1Department of Mechanical Engineering, University of South Florida, 2Department of Materials Science and Engineering, Virginia Polytechnic Institute and State University, 3Department of Civil and Environmental Engineering, University of South Florida
Engineering
Fabrication of Refractive-index-matched Devices for Biomedical Microfluidics
1Department of Chemical Engineering, University of Utah, 2Huntsman Cancer Institute, University of Utah
Engineering
Generation and Control of Electrohydrodynamic Flows in Aqueous Electrolyte Solutions
1Department of Mechanical Science and Bioengineering, Graduate School of Engineering Science, Osaka University, 2Division of Mechanical Science and Technology, Faculty of Science and Technology, GUNMA University
Engineering
A Standard and Reliable Method to Fabricate Two-Dimensional Nanoelectronics
1Department of Physics, National Taiwan Normal University, 2National Applied Research Laboratories (NARL), National Nano Device Laboratories (NDL)
Engineering
Force-Clamp Rheometry for Characterizing Protein-based Hydrogels
1Department of Physics, University of Wisconsin-Milwaukee
Engineering
Microparticle Manipulation by Standing Surface Acoustic Waves with Dual-frequency Excitations
1School of Mechanical and Aerospace Engineering, Nanyang Technological University
Engineering
Three-Dimensional Ultrasonic Needle Tip Tracking with a Fiber-Optic Ultrasound Receiver
1Wellcome/EPSRC Centre for Interventional and Surgical Sciences, University College London, 2Department of Medical Physics and Biomedical Engineering, University College London, 3Department of Anaesthesia, University College Hospital, 4St Bartholomew's Hospital and Queen Mary University of London, 5Institute for Women's Health, University College London, 6Centre for Medical Imaging Computing, University College London, 7GePaSud, University of French Polynesia, 8Department of Development and Regeneration, KU Leuven (Katholieke Universiteit), 9NIHR University College London Hospitals Biomedical Research Centre
Engineering
Film Control to Study Contributions of Waves to Droplet Impact Dynamics on Thin Flowing Liquid Films
1Department of Chemical Engineering, Imperial College London
Engineering
Fabrication of Soft Pneumatic Network Actuators with Oblique Chambers
1State Key Laboratory of Mechanical System and Vibration, Shanghai Jiao Tong University, 2Robotics Institute, School of Mechanical Engineering, Shanghai Jiao Tong University, 3University of Michigan-Shanghai Jiao Tong University Joint Institute, Shanghai Jiao Tong University
Engineering
Measuring Magnetically-Tuned Ferroelectric Polarization in Liquid Crystals
1Division of Materials Physics, Graduate School of Engineering Science, Osaka University, 2Division of Chemical Engineering, Graduate School of Engineering Science, Osaka University, 3Department of Advance Materials Science, University of Tokyo
Engineering
A 3D-printed Chamber for Organic Optoelectronic Device Degradation Testing
1Department of Engineering Physics, McMaster University, 2Department of Physics, Engineering Physics and Astronomy, Queen's University
Engineering
Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System
1Department of Mechanical and Aerospace Engineering, Case Western Reserve University
Engineering
A Soft Tooling Process Chain for Injection Molding of a 3D Component with Micro Pillars
1Department of Mechanical Engineering, Technical University of Denmark
Engineering
Measurement of Dynamic Force Acted on Water Strider Leg Jumping Upward by the PVDF Film Sensor
1State Key Laboratory of Precision Measuring Technology and Instruments, Tianjin University
Engineering
Determination of the Excitation and Coupling Rates Between Light Emitters and Surface Plasmon Polaritons
1State Key Laboratory of Optoelectronic Materials and Technologies and Guangdong Province Key Laboratory of Display Material and Technology, School of Physics and Engineering, Sun Yat-sen University, 2Department of Physics, The Chinese University of Hong Kong
Engineering
Surgical Techniques for Catheter Placement and 5/6 Nephrectomy in Murine Models of Peritoneal Dialysis
1Molecular Biology Research Centre Severo Ochoa, Spanish National Research Council, 2IdiPAZ Research Institute, La Paz University Hospital, 3Princesa Research Institute, La Princesa University Hospital
Engineering
An Efficient Method for Selective Desalination of Radioactive Iodine Anions by Using Gold Nanoparticles-Embedded Membrane Filter
1Advanced Radiation Technology Institute, Korea Atomic Energy Research Institute, 2Department of Chemistry, Kyungpook National University, 3Department of Radiation Biotechnology and Applied Radioisotope Science, University of Science and Technology
Engineering
Generation of Size-controlled Poly (ethylene Glycol) Diacrylate Droplets via Semi-3-Dimensional Flow Focusing Microfluidic Devices
1Graduate School at Shenzhen, Tsinghua University, 2The State Key Laboratory of Precision Measurement Technology and Instruments, Tsinghua University
Engineering
Fabrication of Magnetic Nanostructures on Silicon Nitride Membranes for Magnetic Vortex Studies Using Transmission Microscopy Techniques
1CEITEC BUT, Brno University of Technology
Engineering
Construction and Operation of a Light-driven Gold Nanorod Rotary Motor System
1Department of Physics, Chalmers University of Technology
Engineering
