Fuente: Laboratorio de Alan Lester – Universidad de Colorado Boulder
Mapas geológicos primero fueron hechas y utilizadas en Europa, en el mediados-finalessiglo 18 . Desde entonces, ellos han sido una parte importante de las investigaciones geológicas del mundo que se esfuerzan por entender las distribuciones de la roca en la superficie de la tierra, en el subsuelo y su modificación a través del tiempo. Un moderno mapa geológico es una representación de datos de rocas y estructuras rocosas en una vista en planta de dos dimensiones. La base para mapas más geológicos es un mapa topográfico, en que color las variaciones han sido colocadas para representar unidades de roca específicos. Los límites entre las unidades de roca se llaman contactos. Además de las líneas de contacto, mapas geológicos contienen símbolos que representan características clave, como la inmersión y la huelga de las unidades de roca, anticlinales y sinclinales y las huellas de las superficies de falla.
Aunque la vista del mapa bidimensional es útil, una de las tareas clave de un geólogo es inferir el tipo y la orientación de las rocas en el subsuelo. Esto se hace mediante reglas geológicas, inferencias y proyecciones hacia abajo de la superficie. El resultado es una sección geológica, una vista que esencialmente proporciona una imagen de corte, igual que uno vería en una pared del cañón o en una revegetación.
Este segmento hipotético en la tierra, proporcionando una tercera dimensión (profundidad), es la clave a un host de aplicaciones geológicas. Secciones transversales se utilizan para evaluar los modelos temporales de formación de la roca a través del tiempo. En otras palabras, el objetivo es recrear una secuencia paso a paso de que las rocas y estructuras llegaron primeras, último y en el medio. También están acostumbrados a específicos modos de deformación – de determinar si las rocas han sido sometidos a tensiones de compresión, extensión u otras.
Geológicos de las secciones transversales ayudan a identificar las regiones del movimiento de las aguas subterráneas, evaluar sitios potenciales para los depósitos minerales económicos y localizar reservorios de petróleo y gas.
For this demonstration, a portion of the Carter Lake, Colorado, USGS 7.5-minute Quadrangle Map was used. This notation means that 7.5 minutes of longitude and 7.5 minutes of latitude define the E-W and N-S boundaries on the map. On the east side of the cross section line A-A’, the rock layers dip to the west; in contrast, on the west side, the layers dip to the east. It can be inferred that these layers meet in the subsurface to form a bowl-shaped fold-structure, known as syncline. Ultimately, all folds (whether down-warps, such as synclines, or up-warps, such as anticlines) are a product of compression-style deformation. When rocks have been squeezed, they show plastic deformation features (folding), especially if deformation has occurred relatively rapidly, with high-confining pressures and elevated temperatures in Earth’s upper crust. In contrast, rapid application of stress, low-confining pressure, and low temperatures are more likely to produce brittle deformation, known as faulting.
Cross-sections provide a means to analyze and assess the subsurface orientation of rock units. Geologists use the relative dating rules of cross-cutting and superposition to determine the timing of deposition and deformation. For example, when one layer sits above another, it can be inferred that the top layer is most likely younger than the layer below. Furthermore, if a fault cuts across a particular rock unit, then the fault is most likely younger than the rock unit it offsets.
Some specific applications include the determination of geologic history, groundwater flow analysis, mineral deposits, and oil and gas reservoirs. Relative dating techniques permit an assessment of a sequence of geologic events, including deposition, intrusion, and deformation (folds and faults). Geologists seek to understand the earth in not only the three spatial dimensions, but also within the context of a temporal dimension- the idea being to reconstruct geological change through time.
Cross sections are a key to evaluating fluid flow in the subsurface. Understanding the orientation of flow-enhancing layers (aquifers) versus flow-preventing layers (aquicludes) is the key to evaluating the motion of groundwater. This also provides an application for determining where wells are best to be drilled. It allows for analysis of aqueous pollutant movement and possible mitigation strategies. In general, rock types that contain considerable pore space (e.g. sandstone or highly fractured igneous/metamorphic rocks) will be aquifers. In contrast, rock types that contain limited pore space (or pores that lack inter-connectivity) will more likely be aquicludes.
Most economic mineral deposits (e.g., Au, Ag, Cu, Mo, etc.) are associated with igneous rocks. If igneous rocks outcrop on the surface, and their surface contacts can be assessed, then one can determine where possible ores can be found in the subsurface. Most oil and gas reservoirs are associated with sedimentary rocks, because these are the rock types that contain hydrocarbon sources (decayed organics, both terrestrial and marine). Here, cross section analysis is absolutely critical to determining where fold or fault traps are likely to exist, and if they contain petroleum resources. For example, up-warps (anticlines) are a classic location for oil and gas drilling. This is because mobile hydrocarbons tend to flow upward, within permeable layers, until they reach the peak (or axis) of an anticline. If the permeable layer is capped by an impermeable layer, then a hydrocarbon reservoir accumulates and pools at the apex of the fold.
Geologic cross-sections can assess temporal models of rock formation through time.
Using geologic maps, cross-sections can be generated which predict the strata of the rocks sub-surface, and estimate the rock shape above ground prior to erosion.
The resulting cross-section is a cutaway image much like those seen in canyon walls or road cuts. While geologists may be able to infer such features from a plan-view geologic map, the addition of a cross-section provides a third dimension of information that can greatly enhance the ability to evaluate folds and faults.
This video will illustrate the process of creating a geologic cross section, and highlight some of the extensive uses of this geological tool.
The first step in creating a geologic map is to take a topographic map and onto this color-code the regions containing different rock types. In the field, geologists observe mineralogic and textural features, which are then used to identify distinct rock types and rock units. The lines between each rock unit section are the contacts. Within each rock type, strike and dip data will be added to illustrate the surface outcrop orientation of the rock strata.
These strike and dip data indicate fold-type deformations that generate up-warped strata, analogous to an upside down bowl, which are referred to as anticlines. The folds that involve down-warped strata are synclines. In contrast, faults are a result of brittle deformation, whereby rocks break instead of bending along a distinct surface-of-rupture. This surface is the “fault-plane.”
Taken together, rock type, position, and orientation, are used to create a geologic cross-section. The first step is to create a topographic profile, which shows the elevation and contour of the target region. The geologic data is then added to this profile. This cross-section can now be used to infer the subterranean structure. For example, beds dipping away from a central axis are indicative of anticlines, whereas beds that dip towards would indicate synclines.
Further, geologic cross sections are used to reconstruct folds and faults that may be cryptic, due to the effects of erosion on the surface features. This is achieved by extrapolating the existing surface and subsurface data upwards above the existing plane.
Now that we are familiar with the principles behind the construction of a geologic cross section, let’s take a look at how this is carried out on an example map.
To construct a geologic cross-section, first take a geologic map of the target survey area. Begin by choosing two points that define a cross section profile of interest. Label these points as A and A’. These should be selected so that a line between them will be approximately perpendicular to the strike directions of the intervening rock units. Connect these points, and create a topographical profile, without vertical exaggeration, based on the contours that intersect the line. Next, take a strip of paper and align it along the A-A’ line, and carefully mark the contacts between the different rock units.
At each contact, the dip information of the adjoining layers is used to project the boundary into the subsurface. Note that in the projection to the subsurface, we use an average dip across the fold. This maintains constant bed thickness in the projection.
Using a protractor, measure the angle of the dip according to the original map, and extend the rock layers in straight lines below the surface. Projecting this information at each contact point will give a rough predicted cross-sectional view of the rock strata beneath the surface. Next, look for patterns in the rock projections that may indicate folds of the same type of rock strata. If these predicted strata lines appear to meet, this indicates folding of the same substrate, and they should be joined in a smooth projection based on the dip magnitudes given at the surface.
Finally, extend the rocks layers into the above ground region. This shows the inferred presence of rocks and geologic structure prior to erosion.
The map used for this demonstration shows a portion of the MASONVILLE, COLORADO, 7.5 minute quadrangle, USGS geologic map. The rock layers and contacts have been transferred to the geologic profile, and projections made into the subsurface and surface. In the case of one of the units, the Dakota group, labeled KD and highlighted in green, we see the layers dipping on one side of what is referred to as the anticline, to the east, and to the west on the opposite side. Overall, the projections suggest an anticline-syncline combination, and the crest of the anticline is recorded on the original map itself as a dashed line, with the trough (pronounce “trof”) of the syncline indicated to the west by a different dashed line. This combination results in a bowed down set of rock formations, and a bowed up formation, produced by past compressional stresses on the rock strata. The Dakota group, which follows this anticline-syncline pattern, is a unit of importance as it represents a sandstone, which will contain water or oil, which may be of interest for mining.
Geologic cross-sections are useful tools for a number of types of geological investigation. Some of these applications are explored here.
Analyzing sequences of deposition, intrusion, deformation, or erosion over time can inform not only the spatial dimensions of the rock, but also the temporal dimension. Using this information, it is also possible to simulate and anticipate future changes in the Earth’s structure, such as the erosion of softer substances, leaving harder rock exposed.
Most economically important mineral deposits; including gold, silver, copper, and molybdenum; are associated with igneous rocks. If such rocks are found on the surface during a geological survey, and their surface contacts can be assessed, it is possible to use a geologic cross section to extrapolate where possible ores can be found in the subsurface.
Geologic cross-sections are key to evaluating fluid flow in the subsurface. Understanding the orientation of flow-enhancing layers, or aquifers, versus flow preventing layers, or aquicludes, allows geologists to predict the motion of groundwater, and potentially determine suitable areas for drilling of wells. In general, rock types containing considerable pore space, like sandstone, will be aquifers, and those with denser structure and little pore space, like slate, will act as aquicludes. Crucially, this information also allows for analysis of aqueous pollutant movement, and development of possible mitigation strategies in such events.
You’ve just watched JoVE’s introduction to geologic cross-sections. You should now understand how to create a geologic profile from a geologic map, and the uses and applications of these geologic cross-sections.
Thanks for watching!
