Membrane Transport Processes Analyzed by a Highly Parallel Nanopore Chip System at Single Protein Resolution

Summary

The presented protocol describes the analysis of membrane protein mediated transport on the single transporter level using pore-spanning solvent-free lipid bilayers. This is achieved by the creation of bulk produced nanopore array chips, combined with highly parallel data acquisition and analysis, enabling the future establishment of membrane protein effector screenings.

Abstract

Membrane protein transport on the single protein level still evades detailed analysis, if the substrate translocated is non-electrogenic. Considerable efforts have been made in this field, but techniques enabling automated high-throughput transport analysis in combination with solvent-free lipid bilayer techniques required for the analysis of membrane transporters are rare. This class of transporters however is crucial in cell homeostasis and therefore a key target in drug development and methodologies to gain new insights desperately needed.

The here presented manuscript describes the establishment and handling of a novel biochip for the analysis of membrane protein mediated transport processes at single transporter resolution. The biochip is composed of microcavities enclosed by nanopores that is highly parallel in its design and can be produced in industrial grade and quantity. Protein-harboring liposomes can directly be applied to the chip surface forming self-assembled pore-spanning lipid bilayers using SSM-techniques (solid supported lipid membranes). Pore-spanning parts of the membrane are freestanding, providing the interface for substrate translocation into or out of the cavity space, which can be followed by multi-spectral fluorescent readout in real-time. The establishment of standard operating procedures (SOPs) allows the straightforward establishment of protein-harboring lipid bilayers on the chip surface of virtually every membrane protein that can be reconstituted functionally. The sole prerequisite is the establishment of a fluorescent read-out system for non-electrogenic transport substrates.

High-content screening applications are accomplishable by the use of automated inverted fluorescent microscopes recording multiple chips in parallel. Large data sets can be analyzed using the freely available custom-designed analysis software. Three-color multi spectral fluorescent read-out furthermore allows for unbiased data discrimination into different event classes, eliminating false positive results.

The chip technology is currently based on SiO₂ surfaces, but further functionalization using gold-coated chip surfaces is also possible.

Introduction

The analysis of membrane proteins has become of increasing interest for basic and pharmaceutical research in the past 20 years. The development of novel drugs depends on the identification and detailed characterization of new targets, currently being one of the limiting factors. The fact that about 60% of all drug targets are membrane proteins¹, makes the development of techniques to elucidate their function most important.

In the past, techniques for the study of electrogenic channels and transporters have been developed in multitude^2-4. Non-electrogenic substrates in contrary present a more challenging task. They are however of special interest as prime drug targets, as they control the flux of solutes and nutrients across the cell membrane and function as key receptors in signaling cascades⁵.

Considerable effort has been put into the development of techniques to study the function of membrane transport proteins^6,7. Systems using solid-supported membranes have emerged as most promising tools in this field^8-10, including solid supported lipid bilayers, tethered bilayers^11,12, microblack lipid membranes^13,14 and native vesicle arrays^15,16 to name a few. Some of them are even available as commercial setups^17,18. Some examples have been published combining the ability to study single membrane proteins in a highly parallel manner^14,19, a prerequisite for screening applications. However, these methods rarely bridge from basic research to the industrial environment. The difficulties often lie in the ability of the system to be automatable, the cost-intensive production and/or laborious preparation. An approach overcoming all the above mentioned obstacles is the final aim.

The technique presented here was developed to study membrane channels and transporters in vitro in a controlled environment on the single protein level^20-22. Reconstitution of purified membrane proteins into LUVs is much more established than comparable approaches for GUVs^23-26 or black lipid membranes²⁷. They can directly be applied to the chip surface, where bilayer formation is taking place via a self-assembly process. The glass-bottom design of the nanoporous chip (Fig. 1) allows for air microscopy, which permits the straightforward automation of the system. In combination with a motorized stage multiple chips can be measured at the same time, with each field of view containing thousands of sealed cavities for analysis.

Figure 1. Design of multiplexed nanopore biochips. A) A silicon-on-insulator (SOI) wafer is structured by reactive-ion etching. Approximately 1,150 individual chips are fabricated from each wafer with identical properties and quality. B) Each chip comprises 250,000 individual microcavities with nano apertures. Scale bar: 200 µm. C) Each cavity is addressable via multi-spectral fluorescence read-out. An intransparent top layer blocks the fluorescent signals from the buffer reservoir, making the biochip compatible with inverted fluorescence microscopes. D) Atomic force microscopy (AFM) imaging reveals evenly arranged pore openings and surface roughness of the silicon dioxide layer of 3.6 nm (n = 40) optimal for vesicle fusion. Scale bar: 5 µm. E) Scanning electron microscopy (SEM) image shows a cross-section through the nanopore allowing access to the femtoliter cavities inside the silicon chip. This figure was reused with permission from ²¹. Please click here to view a larger version of this figure.

All data analysis is performed using freeware to guarantee unrestricted access for end users. Time series are analyzed using free image processing software and a custom build curve analysis software enabling batch processing and straightforward correlation of large datasets with multiple fluorescent channels and thousands of curves.

The model protein used in this protocol is the mechanosensitive channel of large conductance (MscL) channel protein derived from E. coli. It functions as a valve to release osmotic shock in nature, but was modified in such a way that rationally designed synthetic functionalities can covalently be attached to the channels constriction side. Via charge-repulsion of the covalently bound activator (MTSET) the channel is triggered to open, creating a nano-valve. Small molecules like ions, water, small proteins, but also small fluorophores can permeate through the channel. Here, the protein is used as a model to demonstrate the ability of the system to detect protein-mediated translocation.

Protocol

1. Preparation of Large Unilamellar Vesicles (LUVs)

1. Clean a round bottom flask (10 ml volume) with nitrogen gas to remove any dust particles. Rinse the round bottom flask with ethanol.
   Note: Residual ethanol can be tolerated and does not disturb subsequent steps.
2. Wash a 1 ml glass syringe 4x with chloroform, to remove any contamination. Add 4 ml SoyPC20 (25 mg/ml in chloroform) to the round bottom flask and dope the lipid solution with an additional DOPE^ATTO390 to a final concentration of 0.1 mol%.
   Note: Instead of DOPE^ATTO390 other fluorophore-labeled lipids or lipophilic dyes can also be used, depending on available excitation sources.
3. Connect the round bottom flask to a rotary evaporator. Dry the lipid film for 40 min at 300 mbar, 30 °C water bath temperature and maximal rotation speed, to form a homogenous lipid film on the glass wall of the flask.
4. Transfer the flask to a high vacuum pump and dry the lipid film for additional 30 min at room temperature.
5. Add 5 ml buffer (20 mM Tris, 150 mM NaCl, pH 8.0; sterile filtered) and 8 glass beads (2.7-mm diameter, ethanol washed and dried) to the flask. Connect the flask to the rotary evaporator and rotate without vacuum at 50 °C at maximum speed.
   Note: Glass beads mechanically displace the lipid film from the glass wall, leading to (multilamellar) vesicle formation. After 45 min rotation the solution appears milky and no residual lipid film should be visible at the flask walls. Instead of glass beads other methods like sonicating the flask in a water bath sonifier, vortexing the flask or the gentle rehydration method are also applicable.
6. Transfer the flask under inert gas (argon) to an ultrasonic bath and sonicate for 4 min at room temperature.
   Note: The ultrasound shockwaves disrupt the liposomes, making them unilamellar.
7. Split the LUV solution into 1 ml aliquots.
8. Perform 5 freeze/thaw cycles by freezing the LUV solution in liquid nitrogen, followed by thawing at 40 °C in a water bath.
   Note: This leads to rupture and spontaneous rearrangement of individual liposomes with each other, leading to size increase.
9. At the last freezing step store all samples at -80 °C.
   Note: The LUVs will be stable for at least 6 months.

2. Protein Reconstitution

1. Thaw 1 ml LUV aliquot on ice. Directly before reconstitution, extrude liposomes 17x through a 400 nm polycarbonate filter membrane using a mini extruder.
   Note: Lipid aggregates will be removed and the final homogenous size distribution is reached.
2. Destabilize LUVs by addition of 4% Triton X-100 (v/v) to a final concentration of 0.25% (v/v) and incubate for 5 min at 50 °C.
   Note: The amount of liposomes used in this step depends on the mass of the purified MscL^G22C used (see step 2.3). Purify MscL^G22C (derived from E. coli) as described in detail in ²⁸.
3. Mix purified MscL^G22C and detergent-saturated liposomes at 1:20 (w/w) ratio and incubate for additional 30 min at 50 °C.
4. For detergent removal add bio-beads in Tris buffer (20 mM Tris, 150 mM NaCl, pH 8.0; sterile filtered) to the protein/liposome solution, with 16 mg (wet weight) bio-beads per µl detergent used to destabilize liposomes in step 2.2.
5. Perform detergent removal overnight (16 hr) at 4 °C on a rotating plate.
   Note: The constant mixing of the solution ensures optimal detergent removal.
6. After detergent removal store proteoliposomes at 4 °C and use for experiments on the same day.

3. Activity Assay

1. During protein reconstitution take a 100 µl aliquot of detergent-destabilized proteoliposome solution after finishing step 2.3.
2. Add 1 volume of calcein (30 mM) to the protein-liposome solution and incubate additional 5 min at 50 °C.
3. Remove detergent from the solution as described in step 2.4 - 2.6.
4. After detergent removal equilibrate a size-exclusion column (20 ml bed volume or more) with Tris buffer (3x the bed volume).
   Note: Proteoliposome separation can be performed at room temperature, however keeping the sample constantly at 4 °C is advised to ensure best protein activity after fractionation.
5. Separate proteoliposomes from free calcein by applying the entire aliquot (200 µl) to the size exclusion column. Allow the mixture to soak into the column, followed by elution of the proteoliposomes from the column via continuous buffer application on top using gravity flow. Observe the calcein containing proteoliposomes as a discrete orange band in the elution front. Collect fractions of 500 µl respectively.
   Note: Free calcein dye will elute after the proteoliposome fraction with complete separation.
6. Pipette 80 µl of each fraction onto a micro-well plate for fluorescent read-out and identify the fraction containing the highest amount of calcein containing proteoliposomes via fluorescence emission. Detect fluorescence at 520 nm with excitation at 490 nm. Use the proteoliposome fraction with the highest signal for the following activity assay.
7. Mix 20 µl of the proteoliposome-containing fraction with 980 µl Tris buffer in a 1 ml fluorescence cuvette.
8. Measure fluorescence emission at 520 nm (excitation 490 nm) using a spectrofluorometer. Record for 1 min and then add 25 µl of MTSET ([2-(trimethylammonium)ethyl]methanethiosulfonate) from a stock solution (160 mM) and mix well. Keep on recording during mixing. Always prepare the stock solution fresh directly before use.
   Note: Once solved in buffer MTSET hydrolyzes within 30 min and will be non-reactive. MTSET can be weighed and kept as dry powder aliquot at -20 °C until use.
   Note: Once activated the MscL^G22C channel opens and releases the entrapped calcein, leading to a local concentration decrease of the calcein when effluxing the proteoliposomes and subsequent dequenching of the dye, resulting in an increase of the fluorescence emission.
9. After the fluorescence emission has reached a stable plateau again, solubilize the liposomes by addition of 50 µl Triton X-100 (4% v/v).
   Note: Ideally no further fluorescence increase can be observed, implying active protein in every liposome.

4. Size Distribution Measurement of LUVs Using Nano-particle Tracking

1. Note that only minimal samples of the liposome or proteoliposome solution are necessary for size distribution analysis using the nanoparticle tracker. Dilute a liposome solution of 5 mg/ml lipid concentration 1:5,000 (v/v) in buffer (20 mM Tris, 150 mM NaCl, pH 8.0; sterile filtered) for analysis to a final volume of 1 ml. Filter all buffers used for dilution and prior LUV preparation and reconstitution using a 0.2 µm membrane to remove any suspended particles like dust that would disturb size distribution measurements.
2. Wash the flow-chamber with ultra-pure water.
3. Use the surface markers to focus on the light beam. Inject approximately 300 µl of the diluted liposome sample and immediately close the exit valve to stop the flow inside the flow chamber, without introducing any air bubbles.
4. Adjust focus and camera shutter/gain settings to ensure adequate scattering signal of the sample for detection.
   Note: 20 - 80 signals should be clearly visible in the field of view. Prevent overcrowding (> 80 signals) as the software will not be able to track individual signals when overlapping.
5. Go to the "Capture" screen. Adjust the temperature control to 25 °C and the capture duration to 90 sec using the software controls. Press "Record" to start recording a time series.
   Note: Upon completion of the time series a new window opens.
6. Save the time series in the given format (*.avi). For practical reasons during batch analysis save all files in a single folder.
7. Open the exit valve and inject another 300 µl into the flow chamber. Close the valve and repeat steps 4.3 - 4.6 twice.
8. After completing all sample runs wash the flow chamber with 5 ml ultra-pure water. Go to the "Pre-Process" screen. Set the calibration parameters temperature = 25 °C and viscosity = 0.91 for the Tris buffer used in this protocol.
9. Open the batch process window and load the recorded time series (Advanced/Batch Process/Set File 1-3). Press "GO" to start the size distribution analysis.
   Note: the analytical software automatically tracks the single particles and calculates their diameter based on their movement behavior using the parameters set in step 4.8.
   Note: The resulting size distribution analysis saves automatically into the same folder as the time series files.
10. Additionally create a report file to summarize the results (Export/Create Report PDF).

5. Chip Holder Preparation

1. Weigh 1.0 g of MDX4 medical grade elastomer base and 0.1 g MDX4 curing agent into a 50 ml reaction tube. Blend both thoroughly with a glass bar.
2. Put the tube into a desiccator for 1 hr to degas the adhesive. Afterwards use it within 30 min for chip gluing, as the adhesive will harden and be too hard to work with.
3. During elastomer degassing (step 5.1) clean an objective glass slide thoroughly with chloroform to remove any contaminations before chip bonding. Rinse the slide with 5 ml of chloroform using a glass syringe. Collect the chloroform in an underneath positioned beaker. After washing let the slide dry.
   Note: Perform this step under a fume hood. Alternative to chloroform, other organic solvents like acetone can also be used.
4. Deposit a small amount of the adhesive bonding material onto the cover glass using a pipette tip (crystal tips for 10 µl pipettes). Remember that the chips have to fit into the 8-chamber slide holder later on and have to be placed on the slide accordingly.
5. Carefully remove one chip at a time from the wafer board using fine tip tweezers and deposit the chip on the drop of adhesive on the cover glass. Ensure that the coated side of the chip faces upwards.
6. Gently push the chip onto the cover glass with the back of a blunt PE tweezers. To ensure that the glue is dispensed evenly underneath the chip, carefully slide the chip forth and back. CRITICAL STEP: Ensure that no air bubbles are trapped underneath the chip, as it will disturb optical imaging of the chip cavities later on. Also ensure that no adhesive material contaminates the chip surface.
7. Desiccate the finished cover glass for 2 hr at 65 °C in a cabinet dryer.
   Note: Chips are still coated with a protective layer originating from their fabrication that needs to be removed.
8. To remove the protective layer, perform a sequential solvent washing step. During the curing of chips, preheat a water bath to 54 °C.
9. Place 3 glass beakers into the water bath, two of them filled with isopropanol and one filled with acetone.
10. Insert the chip cover glass into a slide holder and submerge it into the first isopropanol filled dish for 10 min. Afterwards transfer it to the acetone filled dish, incubate again for 10 min before transferring it for the final washing step to the second isopropanol dish and incubate another 10 min.
11. Remove the slide holder from the dish and carefully wash it extensively with ultrapure water, followed by drying the chips with a gentle stream of nitrogen gas.
12. Take-off the lamination sheet from the 8-well sticky-slide and put it backwards on the bench. Carefully pick up the cover slide and gently press onto the sticky-slide with the chips facing the wells. Let the finished chip holder rest for a couple of minutes before use.

6. Assay Preparation

Note: Nanopore chips glued to a cover glass and separated by an 8-well sticky-slide possess the benefit, that multiple chips can be addressed in a single experimental run, with chips being completely separated from each other.

1. After chip holder preparation, rinse each chip with pure ethanol and blow dry with nitrogen gas, to remove any contaminations like dust.
2. Clean the chip surface with air, oxygen or nitrogen plasma. Depending on the type of plasma cleaning time-periods vary: perform oxygen plasma treatment for 1 min, air and nitrogen plasma for 5 min at 0.3 mbar at 80% power setting (RF power medium or high).
3. After plasma cleaning incubate chips in pure ethanol for 10-15 min to ensure cavity wetting.
4. Stepwise exchange ethanol for buffer by adding 400 µl of Tris buffer (20 mM Tris, 150 mM NaCl, pH 8.0; sterile filtered), followed by mixing of the solution without introducing air bubbles and subsequent removal of 400 µl. Repeat this procedure 12 times, to ensure ethanol removal.
   Note: Ethanol would be harmful for liposomes and suspended lipid bilayers.
5. Dope Tris buffer (20 mM Tris, 150 mM NaCl, pH 8.0; sterile filtered) with 5 mM CaCl₂ and 1 µM Oy647 dye. Completely remove the washing buffer from the chip and immediately add the doped buffer to the chip. Note: Chips will be covered with a thin buffer film after wash buffer removal, so the chip is not in direct contact with air, ensuring a constant wetting of the cavities and the chip surface.
6. Add 1 mg/ml LUVs or proteo-LUVs in Tris buffer (20 mM Tris, 150 mM NaCl, pH 8.0; sterile filtered) to each well.
   Note: The final volume in each well is 300 µl. Consider subsequent additions of the control dye and the chemical modifier MTSET during doped Tris buffer addition.
7. For pore-spanning lipid bilayer formation on the chip surface incubate the chip for 1 hr at room temperature with the liposome solution. Afterwards wash each chip with 4x 400 µl of Ca²⁺-free Tris buffer.
8. Add the control dye to each well, with a final concentration of 5 µM. The chips are now ready for the translocation assay.

7. Assay Setup

1. Mount the chip holder to the epifluorescence microscope (20X air objective, long working distance). Focus on the rim of the nanopore chip to more easily find the focal plane of the micro-cavities. Once the cavities are in focus scan the nanopore array for a region that displays highest sealing ratio.
   Note: Every inverted epifluorescence microscope can be used to perform chip assays. Depending on the objective magnification (20X - 60X) the number of assayed cavities will vary, with up to 9,000 cavities in a single field of view using 20X magnification. Air objectives with a long working distance are preferable. The use of inverted confocal laser scanning microscopes (CLSM) is also possible, but image acquisition might be the limiting factor due to the limited depth of focus.
2. Optimize the chip illumination.
   Note: Ensure that both dye channels do not exceed the maximum grey scale value, as changes cannot be observed. For export experiments adjust illumination of the translocated dye to 90% of maximum signal capacity. Adjust the control dye in open cavities to 80-90% of maximum signal capacity to clearly detect any leaky membrane sealing.
3. Once all channels are adjusted start the time series. Take images every 10-20 sec for 90 min.
   Note: This is adequate to likewise follow specific and unspecific efflux events.
4. Initialize efflux of the fluorescent substrate by the addition of cysteine-specific, positively charged compound MTSET to a final concentration of 3 mM. Allow at least 5 min of experiment runtime before MTSET addition to be able to later on establish a stable fluorescent signal baseline prior to channel opening. Always prepare MTSET solution fresh directly before usage.

8. Data Analysis

1. Open the time series image stack with a standard version of ImageJ (File/Import/Image Sequence).
2. If fluorescent channels are stacked, split the channels in individual stacks for each channel (Image/Stacks/Stack to Images).
3. Duplicate the first image of the translocation substrate channel for ROI (regions of interest) identification (Image/Duplicate).
4. Convert the image to a binary image (Image/Adjust/Threshold). Ensure that the algorithm used depicts signals for all sealed cavities without overlapping pixilation.
5. Automatically define regions of interest with the particle analyzer tool (Analyze/Analyze Particle). Define a minimum particle size defined, to avoid particle noise. Check the options "exclude on edges" and "include holes". Ensure that resulting ROIs reflect the microcavity array pattern. Interjacent ROIs are artifacts, therefore remove them. Save the ROI list.
   Note: Measurement parameter has to be set to "area" before particle analysis (Analyze/Set Measurements/Area)
6. Open the Time Series Analyzer plug-in (http://rsb.info.nih.gov/ij/plugins/time-series.html), which resizes all ROIs automatically to the same size. Re-size all existing ROIs to a width/height of 6x6 pixels and oval shape (Timer Series Analyzer/AutoROIProperties). Check the option "Resize existing ROIS". Save the resulting resized ROI list.
7. Open the ROI manager (Analyze/Tools/ROI Manager) and load the resized ROI list for each channel of the time series (ROI Manger/More/Open). ROIs will be superposed. To analyze the signal change for each ROI start the Multi Measure tool (ROI Manager/More/Multi Measure), select "Measure all slices" and "One row per slice" and start the multi measure.
   Note: Measurement parameter has to be set to "mean gray value" for this step (Analyze/Set Measurements/Mean gray value)
8. Save the resulting table, giving the mean grey value for each ROI in *.txt or *.xls format.
9. Import the ROI analysis of each imaging channel into NanoCalcFX via the "Import File" option. Set "Use first line for naming series". Set the step size between images according to the time series image acquisition periods and choose the corresponding column and decimal separator.
10. Use the "multiple sheet" option to automatically correlate the graphs of the individual fluorescent channels.
    Note: The events can now be analyzed and classified using the information given by the 3-color spectral information.
11. Fit selected curves using the build-in fit function (fit option).
    Note: The implemented efflux and influx equation is suitable for all monoexponential diffusion-driven events and fit boundaries can be set. Resulting rate constants can be plotted using the histogram tool or exported for further data refinement.

Results

Pore-spanning membranes can easily be created on the nanostructured chip surface in a self-assembled manner. However the underlying process is still delicate and influenced by many parameters like liposome size, monodispersity of the liposome population, lamellarity, lipid- and salt-concentration and chemical surface properties. Most of these parameters have been carefully characterized and standardized in the above protocol. Other parameters however should be checked during every new pre...

Discussion

The technique presented here allows a highly parallel analysis of membrane protein transport. Reconstituted membrane protein systems can directly be applied to the biochip, making the adaption of theoretically every membrane transporter or channel possible. Transport analysis is only limited by the establishment of a fluorescent read-out system, either via direct fluorescence change (translocation of fluorophores or fluorescently labeled substrates) or indirect fluorescence change (pH-sensitive dyes, secondary enzymatic ...

Materials

List of materials used in this article

Name	Company	Catalog Number	Comments
Reagent
[2-(Trimethylammonium)ethyl] methanethiosulfonate	Toronto Research Chemicals Inc.	T792900	MTSET; hydrolized by water. Keep as dry pouder aliquot at -80 °C. Use immediately (30 minutes) after solubilization in buffer.
1 ml gas-tight syringe	Hamilton	#1001
10 ml round flask	Schott Duran
2.7 mm glas beads	Roth	N032.1
2-Propanole	Roth	9866.5
30 cm Luer-Lock Extension Tube	Sarstedt	744304
Acetone	Roth	5025.5
Bio-Beads SM-2 Adsorbent	Bio-Rad	152-3920	need to be activated before first use
CaCl2 Dihydrat	Roth	HN04.3
Calcein	Sigma	C0875	store dark at -20 °C
Chloroform reagent grade	VWR Chemicals	22711324
DOPEATTO390	ATTO-TEC	AD 390-165	store dark at -20 °C
Ethanol absolute	Sigma-Aldrich	32205
Injekt Single-use syringe	Braun	460 60 51V
Injekt-F single-use syringe	Braun	91 66 017V
Keck clips	Schott	KC29
L-α-Phosphatidylcholine, 20% (Soy)	Avanti Polar Lipids	5416016	store under inert gas at -20 °C
NaCl 99.5% p.a.	Roth	3957.2
Nanopore E100 wafer/chips	Micromotive (Mainz/Germany)		available on request
Nucleopore Track-Etch Membrane 0.4 µm	Whatman	800282
Oregon Green Dextran 488 (70 kDa)	life Technologies	D-7173	store dark at -20 °C
Oy647	Luminartis (Münster/Germany)	OY-647-T-1mg	store dark at -20 °C
Rotilabo-syringe filtration, unsterile, pore-size 0.22 µm	Roth	P 818.1
Sephadex G-50	Sigma-Aldrich	G5080	column material for size exclusion chromatography
Silastic MDX4-4210	Dow Corning		curing agent for chip fixation onto cover glass support
sticky-Slide 8-well	ibidi	80828	multi-well chamber for the mounting onto glass slides (chip holder)
Three-way stopcock blue	Sarstedt	744410001
Tris Pufferan 99.9% Ultra Quality	Roth	5429.2
Triton-X 100	Roth	6683.1
Whatman 0.2 µm cellulose nitrate membrane filter	Roth	NH69.1
Name	Company	Catalog Number	Comments
Equipment
Büchi 461 water bath	Büchi
Büchi Rotavapor RE 111	Büchi
Cary Eclipse Fluorescence Spectrophtometer	Varian
LiposoFast Mini Extruder	Avestin
Membrane pump	Vaccubrand	15430
Nanosight Nanoparticle Tracking Microscope	Malvern / Nanosight	LM 14C
NyONE microscope	Synentec		available on request
Pump control	Vaccubrand	CVC 2II
Sonicator bath Sonorex RK100H	Brandelin electronic	31200001107477
Vaccum pump RC5	Vaccubrand	1805400204
Water bath W13	Haake	002-9910
Plasma Cleaner PDC-37G	Harrick Plasma	PDC-37G
Name	Company	Catalog Number	Comments
Software
ImageJ	Open Source	http://imagej.nih.gov/ij/	scientific image processing software
NanoCalcFX	Freeware	http://sourceforge.net/projects/nanocalc/	data analysis/evaluation software for massive transport kinetic datasets
NTA 2.3 Analytical Software	Nanosight		data acquisition and analysis software for nanoparticle tracking microscope
NTA 2.3 Temperature Comms	Nanosight		temperature controle software for nanoparticle tracking microscope