Ressauts hydrauliques
English
Share
Overview
Source : Alexander S Rattner et Mahdi Nabil ; Département de génie mécanique et nucléaire, la Pennsylvania State University, University Park, PA
Lorsque le liquide coule le long d’un canal ouvert à grande vitesse, le débit peut devenir instable et légères perturbations peuvent causer l’extrados liquide de passer brutalement à un niveau supérieur (Fig. 1 a). Cette forte augmentation du niveau de liquide est appelée un ressaut hydraulique. L’augmentation du niveau de liquide provoque une réduction de la vitesse de débit moyen. Ainsi, potentiellement destructeur fluide l’énergie cinétique est dissipée en chaleur. Ressauts hydrauliques sont délibérément conçus dans des œuvres de grande eau, comme les évacuateurs de crues barrage, pour éviter d’endommager et réduire l’érosion qui pourrait être causée par des flux de déplacement rapides. Ressauts hydrauliques aussi naturellement des rivières et des ruisseaux et peuvent être observés dans des conditions domestiques, tels que l’écoulement radial de l’eau d’un robinet sur un évier (Fig. 1 b).
Dans ce projet, on construira une installation expérimentale de l’écoulement. Une vanne sera installé, qui est une porte verticale qui peut être montée ou descendue pour contrôler le débit d’eau d’un réservoir en amont d’un évacuateur de crues en aval. On mesurera le débit nécessaire pour produire des ressauts hydrauliques à la sortie de la porte. Ces résultats seront comparés avec les valeurs théoriques fondées sur des analyses de masse et l’impulsion.
Figure 1 : a. Hydraulic jump se produisant en aval du déversoir en raison d’une légère perturbation à un débit instable de grande vitesse. b. exemple d’un ressaut hydraulique en écoulement radial d’eau d’un robinet domestique.
Principles
Flux de larges canaux ouverts, liquide est seulement limité par une frontière solide inférieure et sa surface supérieure est exposé à l’atmosphère. Une analyse de contrôle volume est possible sur une section d’un écoulement à surface libre pour équilibrer l’entrée et la sortie de transport de masse et de quantité de mouvement (voir fig.2). Si les vitesses sont supposées uniformes à l’entrée et la sortie du volume control (V1 et V2 respectivement) avec profondeurs liquides Hcorrespondant1 et H2, puis sur une masse constante flow solde réduit à :
(1)
Le x-analyse dynamique direction de ce volume de contrôle des soldes des forces de pression hydrostatique (en raison de la profondeur fluide) avec l’entrée et la sortie impulsion débits (Eqn. 2). Les forces de pression agir vers l’intérieur des deux côtés du volume control et correspondent à la densité du liquide (densité liquide fois accélération gravitationnelle : ρg), multiplié par la hauteur moyenne de liquide de chaque côté (H12, H 22), multiplier la hauteur sur laquelle la pression agit sur chaque côté (H1, H2). Cela se traduit par l’expression quadratique sur le côté gauche de Eqn. 2. Les débits de quantité de mouvement par le biais de chaque côté (Eqn. 2, côté droit) sont égaux aux taux de débit massique du liquide dans le volume de contrôle (en : 
, out : 
) multiplié par les vitesses de fluide (V1, V2).
(2)
Eqn. 1 peuvent être substituées dans Eqn. 2 pour éliminer V2. Le nombre de Froude (
) peut également être substitué, qui représente la force relative de la quantité de mouvement fluide afflux aux forces hydrostatiques. L’expression qui en résulte peut être notée :
(3)
Cette équation cubique a trois solutions. L’un est H1 = H2, qui donne le comportement normal des canaux ouverts (profondeur d’aspiration = profondeur de sortie). Une deuxième solution donne un niveau négatif de liquid, qui est non-physiques et peut être éliminé. Le reste de la solution permet une augmentation de la profondeur (ressaut hydraulique) ou une diminution de la profondeur (dépression hydraulique), selon l’entrée du nombre de Froude. Si l’entrée du nombre de Froude (Fr1) est supérieure à un, le flux est appelé supercritique (instable) et a haute énergie mécanique (énergie potentielle de cinétique + gravitationnelle). Dans ce cas, un ressaut hydraulique peut se former spontanément ou en raison des perturbations à l’écoulement. Le ressaut hydraulique dissipe l’énergie mécanique en chaleur, réduisant considérablement l’énergie cinétique et en augmentant légèrement l’énergie potentielle de l’écoulement. La hauteur de sortie qui en résulte est donnée par Eqn. 4 (une solution à l’équation. 3). Une dépression hydraulique ne peut se produire si Fr1 > 1 parce qu’il augmenterait l’énergie mécanique du débit, violer la seconde loi de la thermodynamique.
(4)
La force des ressauts hydrauliques augmente avec entrée nombre de Froude. Fr1 augmente, augmente l’amplitude de H2/h1 et une plus grande partie de l’énergie cinétique d’admission est dissipée en chaleur [1].
Figure 2 : Régler le volume d’une section d’un écoulement contenant un ressaut hydraulique. Entrée et masse et quantité de mouvement par unité de largeur, les débits sont indiqués. Hydrostatique force par unité de largeur indiquées dans le diagramme plus bas.
Procedure
Results
Upstream Froude numbers (Fr1) and measured and theoretical downstream depths are summarized in Table 1. The measured threshold inlet flow rate for formation of a hydraulic jump corresponds to Fr1 = 0.9 ± 0.3, which matches the theoretical value of 1. At supercritical flow rates (Fr1 > 1) predicted downstream depths match theoretical values (Eqn. 4) within experimental uncertainty.
Table 1 – Measured upstream Froude numbers (Fr1) and downstream liquid depths for H1 = 5 ± 1 mm
| Liquid Flow Rate
( |
Upstream Froude Number (Fr1) | Measured Downstream Depth (H2) | Predicted Downstream Depth (H2) | Notes |
| 6.0 ± 0.5 | 0.9 ± 0.3 | 5 ± 1 | 5 ± 1 | Threshold Froude number for hydraulic jump |
| 11.0 ± 0.5 | 1.7 ± 0.5 | 11 ± 1 | 10 ± 2 | |
| 12.0 ± 0.5 | 1.9 ± 0.6 | 12 ± 1 | 11 ± 2 | |
| 13.5 ± 0.5 | 2.1 ± 0.6 | 14 ± 1 | 13 ± 2 |
Photographs of the hydraulic jumps from the above cases are presented in Fig. 4. No jump is observed for 
= 6.0 l min-1 (Fr1 = 0.9). Jumps are observed for the two other cases with Fr1 > 1. A stronger, higher amplitude, jump is observed at the higher flow rate supercritical case.
Figure 4: Photograph of hydraulic jumps, showing critical condition (no jump, Fr1 = 0.9) and jumps at Fr1 = 1.9, 2.1.
Applications and Summary
This experiment demonstrated the phenomena of hydraulic jumps that form at supercritical conditions (Fr > 1) in open channel flows. An experimental facility was constructed to observe hydraulic jump phenomena at varying flow rates. Downstream liquid depths were measured and matched with theoretical predictions.
In this experiment, the maximum reported inlet Froude number was 2.1. The pump was rated to deliver significantly higher flow rates, but resistance in the flow meter limited measurable flow rates to ~14 l min-1. In future experiments, a pump with a greater head rating or a lower pressure drop flow meter may enable a broader range of studied conditions.
Hydraulic jumps are often engineered into hydraulic systems to dissipate fluid mechanical energy into heat. This reduces the potential for damage by high velocity liquid jetting from spillways. At high channel flow velocities, sediment can be lifted up from streambeds and fluidized. By reducing flow velocities, hydraulic jumps also reduce the potential for erosion and scouring around pilings. In water treatment plants, hydraulic jumps are sometimes used to induce mixing and aerate flow. The mixing performance and gas entrainment from hydraulic jumps can be observed qualitatively in this experiment.
For all of these applications, momentum analyses across hydraulic jumps, as discussed here, are key tools for predicting hydraulic system behavior. Similarly, scale model experiments such as those demonstrated in this project, can guide the design of open-channel flow geometries and hydraulic equipment for large-scale engineering applications.
References
- Cimbala, Y.A. Cengel, Fluid Mechanics Fundamentals and Applications, 3rd edition, McGraw-Hill, New York, NY, 2014.
Transcript
A hydraulic jump is a phenomenon that occurs in fast-moving open flows when the flow becomes unstable. When a jump occurs, the height of the liquid surface increases abruptly resulting in an increased depth and decreased average flow velocity downstream. An important side effect of this phenomenon is that much of the kinetic energy in the upstream flow is dissipated as heat. Although hydraulic jumps often arise naturally, such as in rivers or the flow into a household sink, they are also purposely engineered into large waterworks to minimize erosion, or increase mixing. This video will illustrate the principles behind hydraulic jumps in a straight channel and then demonstrate the phenomenon experimentally using a small-scale open channel flow facility. After analyzing the results, some applications of hydraulic jumps will be discussed.
Consider the flow in a wide, straight section of an open channel where a hydraulic jump occurs and construct a control volume on a sluice around the jump. If the flow velocity is uniform at the inlet and outlet, conservation of mass yields a simple relation between upstream and downstream fluid depths. Depth multiplied by velocity is constant. A second relation can be found by considering conservation of momentum. Mass transported across the input and output carries momentum with it equal to the corresponding mass flux multiplied by the flow velocity. Hydrostatic forces on the surface of the control volume also contribute to the momentum balance and must be included. These forces are equal to the average pressure on the surface multiplied by the area. At this point, it is useful to introduce the Froude number, a dimensionless quantity named after the English engineer and hydrodynamicist, William Froude. The Froude number characterizes the relative strength of fluid momentum to hydrostatic forces. Now, if the momentum relation is rewritten in terms of the Froude number, with the output velocity eliminated by substitution using the mass relation, the result is a cubic equation in terms of the ratio of downstream and upstream depths. This equation can be simplified by factoring out the trivial solution where the upstream and downstream depths are equal. The two remaining solutions are easily found using the quadratic equation, but the negative solution can be eliminated since it is non-physical. The remaining solution corresponds to an increase in depth, a hydraulic jump, or a decrease in depth, a hydraulic depression, based on the value of the upstream Froude number. If the upstream Froude number is greater than one, the flow has a high mechanical energy and is supercritical or unstable. A hydraulic depression cannot form in this regime because it would increase mechanical energy and violate the second law of thermodynamics. On the other hand, a hydraulic jump can form, either spontaneously or due to some disturbance in the flow. An input Froude number of one represents the minimum threshold for the onset of a hydraulic jump. Hydraulic jumps dissipate mechanical energy into heat, and significantly reduce the kinetic energy, while slightly increasing the potential energy of the flow. As the Froude number increases, so does the ratio of downstream to upstream depths and the amount of kinetic energy dissipated as heat. Now that we understand the principles behind hydraulic jumps, let’s examine them experimentally.
First, fabricate the open channel flow facility as described in the text. The facility has an upper and lower reservoir connected by an open channel. Water pumped from the lower reservoir is deposited in the upper reservoir with the flow rate controlled and measured by a valve and flow meter in line with the pump. Steel wool in the upper reservoir helps to evenly distribute the water across the width of the section, and the adjustable sluice gate controls the fluid depth as it enters the channel. After flowing through the channel, the fluid is deposited back into the lower reservoir. When the flow facility is assembled, set it up on a bench and remove any nearby electronic devices. Plug the pump into a GFCI outlet to minimize the risk of electrical shock, and then fill the lower reservoir with water. You are now ready to perform the experiment.
Adjust the sluice gate to approximately five millimeters. Measure the final height of the gap underneath the sluice gate using a ruler, and record this distance as the upstream flow depth, H1. When you are finished, turn on the pump and use the valve to maximize the flow rate without exceeding the scale on the flow meter. Use the ruler again to measure the fluid depth after the hydraulic jump. Record the flow rate, along with this second distance which is the downstream flow depth, H2. Before continuing, observe the shape of the hydraulic jump. You should notice larger, more abrupt transitions for higher flow rates, and smaller, more gradual transitions for lower flow rates. Now, repeat your measurements and observations for successively lower flow rates. Try to determine the minimum threshold flow rate for the formation of a hydraulic jump. Once you have found the threshold flow rate, you are ready to analyze the results.
For each volumetric flow rate, you should have a measurement of the downstream fluid depth. The upstream depth is the same for all cases. Complete the following calculations for each measurement and propagate uncertainties along the way. First, determine the inlet flow velocity. Divide the volumetric flow rate by the channel width and upstream depth. Next, evaluate the upstream Froude number using the definition given before, and substituting in the acceleration due to gravity, as well as the upstream height and velocity. Now, use the Froude number and the non-trivial solution for the jump height to calculate the theoretical downstream depth. Compare the theoretical prediction with the measured downstream depth. At supercritical flow rates, the predictions match the measured depths within experimental uncertainty. Look at your results for the threshold flow rate. Within experimental uncertainty, the Froude number is one, as we anticipated from the theoretical analysis. The rate of mechanical energy loss through the hydraulic jump can also be calculated from these data. First, calculate the mechanical energy of the fluid flowing into the jump, which is the sum of kinetic and potential energy flow rates at the inlet. Now, determine the output energy rate in the same way, but with values at the outlet. The rate of mechanical energy dissipation to heat is the difference between the input and output rates. In this experiment, the energy loss rate can reach about 40% of the inlet energy, or higher. These results highlight the effectiveness of momentum analyses and scale model experiments for understanding and predicting the behavior of hydraulic systems. Now let’s look at some other ways hydraulic jumps are utilized.
Hydraulic jumps are an important natural phenomenon with many engineering applications. Hydraulic jumps are often engineered into hydraulic systems to dissipate fluid mechanical energy into heat. This reduces the potential for damage by high velocity liquid jetting from spillways. At high channel flow velocities, sediment can be lifted up from streambeds and fluidized. By reducing flow velocities, hydraulic jumps also reduce the potential for erosion and scouring around pilings. In water treatment plants, hydraulic jumps are sometimes used to induce mixing and aerate flow. The mixing performance and gas entrainment from hydraulic jumps can be observed qualitatively in this experiment.
You’ve just watched JoVE’s introduction to hydraulic jumps. You should now understand how to use a control volume approach to predict the flow behavior, and how to measure this behavior using an open channel flow facility. You’ve also seen some practical uses for engineering hydraulic jumps in real applications. Thanks for watching.